• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.9-15
• /
• 2018

The turbochargers, which are used widely in diesel and gasoline engines, are an effective device to reduce fuel consumption and emissions. On the other hand, turbo-lag is one of the main problems of a turbocharger. Bearing friction losses is a major cause of turbo lag and is particularly intense in the lower speed range of the engine. Current turbochargers are mostly equipped with floating bearings: two journal bearings and one thrust bearing. This study focused on the bearing friction at the lower speed range and the experimental equipment was established with a drive-motor, load-cell, magnetic coupling, and oil control system. Finally, the friction losses of turbochargers were measured considering the influence of the rotating speed from 30,000rpm to 90,000rpm, oil temperature from $50^{\circ}C$ to $100^{\circ}C$, and oil supply pressure of 3bar and 4bar. The friction power losses were increased exponentially to 1.6 when the turbocharger speed was increased. Friction torques decreased with increasing oil temperature and increased with increasing oil pressure. Therefore, the oil temperature and pressure must be maintained at appropriate levels.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.9-14
• /
• 1991

디젤 기관의 출력 성능을 향상시키기 위하여 실린더 내로 흡입되는 공기를 적극적인 방법으로 밀도가 높은 공기로 압입시키는 과급기는 디젤기관의 종합 성능을 결정하는 중요한 인자가 되고 있다. 이와 같은 관점에서 터보 과급기의 성능을 규명하고 과급기의 특성에 관한 사항을 열역학적 해석과 압축기 및 터빈의 성능 특성을 살펴보기로 한다. 여기서는 주로 과급기의 성능 특성을 중심으로 다루기로 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.3
• /
• pp.33-41
• /
• 1995

본 연구는 터보 과급기 부착 디젤 기관의 급가속 운전시 기관과 과급기의 과도 응답 성능을 규명하고 이를 개선하기 위한 실험을 수행하였다. 과도 응답 성능 구명은 일정한 회전 속도로 정상 운전중인 기관의 연료 펌프 랙을 10%에서 40%까지 일정 시간동안 급가속하였을 경우에 대하여 수행하였으며, 이때의 과급기 응답 지연 현상을 개선하기 위한 실험은 급가속과 동시에 압축기 출구의 흡기메니폴드 내에 일정한 압력의 공기를 추가 분사하는 방법을 이용하였다. 그리고 공기 분사 압력, 공기분사 기간, 가속률, 가속 시간 등이 압축기 출구의 압력과 온도, 터빈 입구의 압력과 온도, 실린더 압력, 기관과 과급기 회전 속도 등의 응답 성능에 미치는 영향을 가속전 정상 상태의 기관 회전 속도와 적용부하의 변화에 따라 시간의 함수로 나타내었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.585-591
• /
• 2017

Turbocharging is widely used in diesel and gasoline engines as an effective way to reduce fuel consumption. But turbochargers have turbo-lag due to mechanical friction losses. Bearing friction losses are a major cause of mechanical friction losses and are particularly intensified in the lower speed range of the engine. Current turbochargers mostly use oil bearings (two journal bearings and one thrust bearing). In this study, we focus on the bearing friction in the lower speed range. Experimental equipment was made using a drive motor, load cell, magnetic coupling, and oil control system. We measured the friction losses of the turbocharger while considering the influence of the rotation speed, oil temperature, and pressure. The friction power losses increased exponentially when the turbocharger speed increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.86-93
• /
• 1999

Turbocharger has been used to increase the performance of diesel engine, especially ship engine , for years. Recently, the turbocharger is being adopted not only for an agricultural engine but also for an automobile engine. To improve the performance of diesel engine , the problem of the reduction of A/F ratio in high speed should be solved. Turbocharger is well known for its cost effectiveness, reliability and duration . In this study, an experiment was conducted to verify simulation program . The results for natural aspiration engine and turbocharged engine were compared. In order to estimate the characteristics of exhaust gas, D-13 mode was selected. Power, torque and BSFC of turbocharged engine were increased than those of natural aspiration engine by about 48%, 46% and 5%, respectively . The components in exhaust gas except NOx from turbocharger engine were less than the amount set up for 2000-year regulation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.723-729
• /
• 2019

Turbochargers are an effective device to reduce the fuel consumption. In this study, the mass flow rate of pulsating flow in the twin-scroll turbocharger for the gasoline engine of passenger vehicles was measured. Pulsating flow was achieved using a pulse generator and the mass flow rate of the unsteady pulsating flow was analyzed by comparing it with those of the steady flow. The pulse generator consisted of a rotating upper plate and a fixed lower plate. To measure the mass flow rate of unsteady flow, the orifice flow meter equipped with the difference pressure transducer was used. To analyze the low speed performance of the turbocharger, the measurement was carried out in the speed of turbocharger from 60,000rpm to 100,000rpm. The mass flow parameters of the unsteady pulsating flow showed a large difference compared to those of the steady flow. Those of the unsteady flow showed the hysteresis loop surrounding the mass flow parameters of the steady flow and the maximum variation of the mass flow parameters were 5.0 times those of the steady flow. This phenomenon is the result of the filling and emptying the turbine volute space due to pulsating flow.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.765-770
• /
• 2020

The turbochargers used widely in diesel and gasoline engines are effective devices to reduce fuel consumption and emissions. In this study, the isentropic turbine efficiency of the steady flow in a twin-scroll turbocharger for the passenger vehicle gasoline engine was analyzed. The cold gas test bench was designed and made. The pressure and temperature of the inlet and exit of the turbine were measured at 60,000, 70,000, 90,000, and 100,000rpm under the steady-state flow. The isentropic turbine efficiency was calculated. The efficiency was the range of 0.53 to 0.57. The BSR and expansion ratio were changed from 0.71 to 0.84 and from 1.24 to 1.72, respectively. The isentropic turbine efficiency decreased with increasing BSR and expansion ratio. The operation of only scroll A or B was compared with that of the twin-scroll turbine. The isentropic efficiency of using only scroll B was higher than those of only scroll A at 60,000rpm. The isentropic efficiency of using only scroll A was higher than those of only scroll B at 100,000rpm. Therefore, the twin-scroll turbine used in this study is operating effectively in the wide speed range.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.90-98
• /
• 2002

The effects of swirl and combustion parameters on the performance and emission in a turbo-charged D.I. diesel engine of the displacement 9.4L were studied experimentally in this paper. Generally the swirl in the combustion process of diesel engine promotes mixing of the injection fuel and the intake air. It is a major factor to improve the engine performance because the fuel consumption and NO$_{x}$ is trade-off according to the high temperature and high pressure of combustion gas in a turbocharged D.I. diesel engine, it's necessary to thinking over the intake and exhaust system, the design of combustion bowl and so on. In order to choose a turbocharger of appropriate capacity. As a result of steady flow test, when the swirl ratio is increased, the mean flow coefficient is decreased, whereas the gulf factor is increased. Also, through engine test its can be expected to meet performance and emissions by optimizing the main parameter's; the swirl ratio is 2.43, injection timing is BTDC 13$^{\circ}$ CA, compression ratio is 16, combustion bowl is re-entrant 5$^{\circ}$, nozzle hole diameter is $\Phi$0.28*6, turbocharger is GT40 model which are compressor A/R 0.58 and turbine A/R 1.19.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1575-1582
• /
• 1992

This study describes the response performances of actual engine speed, turbocharger speed, air mass flow rate through engine, boost pressure ratio, exhaust temperature and combustion efficiency for a six-cylinder four-stroke turbocharged diesel engine during the change in operating conditions by using the computer simulation with test bed. In order to obtain the transient conditions, a suddenly large load was applied to the simulation engine with the several kinds of inertia moment in turbocharger and engine, and engine set speed. From the results of this study, the following conclusions were summarized The inferior response performances was mainly caused by turbocharger lag, and air mass flow rate and boost pressure ratio were closely related to the turbocharger speed. A reduced moment of turbocharger inertia resulted in less transient speed drop and much faster recovery to the steady state of the engine. The increase of moment of engine inertia reduced cyclic variation of engine speed. When a large load was applied to the engine at high speed, the engine could be fastly recovered. However, when the same load was applied to the engine at low speed, the engine was stalled.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.386-391
• /
• 2021

Turbocharging is becoming a key technology for both diesel and gasoline engines. Regarding gasoline engines, turbocharging can help reduce carbon dioxide (CO2) emissions when used in conjunction with other technologies. This paper presents measurements of the turbine efficiency of pulsating flow in a twin-scroll turbocharger for gasoline engines. A cold gas test bench with a pulse generator was manufactured. The turbine efficiencies were calculated using the measured data of the instantaneous pressure and temperature of the inlet and exit of the turbine. The measurements were carried out at turbine speeds from 60,000 to 100,000 rpm under a pulsating flow of 25.0 Hz and 33.0 Hz. The turbine efficiencies ranged from 0.517 to 0.544. At the pulse frequency, 33.3 Hz, the variations in efficiency were 7.7% and 2.6% at turbine speeds of 60,000 rpm and 100,000 rpm, respectively. The turbine efficiency of the pulsating flow compared to those of steady flow was 7.0% and 3.0% lower at a turbine speed of 60,000 rpm and 100,000 rpm, respectively. The pulsating flow deteriorated the turbine efficiency, but the effects of pulsating flow decreased with increasing turbine speed.