• Journal of the Korean Ceramic Society
• /
• v.38 no.1
• /
• pp.52-55
• /
• 2001

Polyacrylonitrile(PAN)-based 탄소섬유와 epoxy resin matrix 내에 장착된 PAN-based 탄소섬유의 전기저항을 탄소섬유와 파괴될 때까지 인장강도를 증가시키며 측정하였다. 탄소섬유가 끊어져 측정 계기가 open-circuit을 나타내기 전까지 탄소섬유의 전기저항 값은 strain이 증가할수록 증가하였으며, epoxy resin은 탄소섬유의 저항값 측정에 거의 영향을 미치지 않았다. 탄소섬유의 저항값 변화는 strain에 대해 정확도 1% 이내로 예측(calibrate)할 수 있었으며 재현성 또한 우수하였다. 따라서 탄소섬유는 재료의 기계적 강도를 증가시키기 위해 사용될 수 있을 뿐만 아니라 구조재료의 파괴를 예측할 수 있는 스마트 센서로서도 사용할 수 있다는 가능성을 확인하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.293-294
• /
• 2012

탄소섬유 복합재의 기계적 강도를 높이기 위하여 탄소섬유상에 ZnO 나노구조체를 도금하는 연구를 수행하였다. 전기도금을 이용하여 정전위법으로 탄소섬유상에 ZnO 나노구조체를 도금시킨 후 에폭시 YD-128과 경화제 KBH1089를 이용하여 탄소섬유 복합재를 제작하였다. 제작된 탄소섬유 복합재는 실험규격 ASTM D2344를 준수하였으며 ILSS(Interaminar Shear Strength)시험으로 강도를 측정하였다. 본 연구결과 탄소섬유에 인가되는 coulomb양을 조절함으로서 ZnO 나노구조체 형상을 제어할 수 있었으며, 일반탄소섬유 복합재와 ZnO 나노구조체가 도금된 탄소섬유 복합재의 강도를 비교하였을 때 ZnO 나노구조체가 도금 된 탄소섬유 복합재에서 더 높은 강도 값을 얻을 수 있었다.

• Composites Research
• /
• v.28 no.5
• /
• pp.254-259
• /
• 2015

Carbon fiber/aluminum (CF/Al) composites were successfully fabricated without pressure casting using wettability modification of carbon fiber. The wettability of liquid aluminum on carbon fibers was enhanced through electroless plating of copper on carbon fibers. Liquid aluminum was well infiltrated into carbon fiber bundles with Cu coating layer due to low wetting angle, and a lot of pores that existed in CF/Al composite without Cu coating on CF were greatly removed. However, a few tiny pores existed in carbon fiber bundles, which is due to not bad wettability between CF and Al but shrinkage cavity that was generated during cooling of CF/Al composite. The tiny pores could be effectively removed by a subsequent rolling.

• Journal of the Korean Ceramic Society
• /
• v.37 no.9
• /
• pp.921-926
• /
• 2000

에틸렌과 프로판가스로부터 Ni 및 Ni-Cu의 합금촉매를 사용하는 화학증착반응에 의해 제조한 나노탄소섬유에 충전재로 하고, 환경 친화적인 폴리비닐알코올을 매트릭스로 이용하여 복합재를 제조하여 전자파 차폐효능을 조사해 보았다. 전자파 차폐용 충전재의 중요한 물성치인 전기전도도는 나노탄소섬유의 반응조건에 따라 매우 민감하게 변했는데, 전체적으로 10000 psi 압력에서 4.2~29 S/cm 사이에 분포하였고 합금촉매보다도 순수한 Ni로 제조된 나노탄소섬유의 전기전도도 값이 높았다. 한편, 나노탄소섬유/폴리비닐알코올 복합재의 전기전도도는 Ni:Cu(7:3) 합금촉매에서 제조된 나노탄소섬유를 충전시켰을 때, 가장 높게 얻어져서 충전재의 전기전도도 외에도 비표면적이 중요한 변수임을 알 수 있었다. PVA 양에 대한 나노탄소섬유의 함량이 증가할수록 나노탄소섬유 복합재의 전기전도도는 기하급수적으로 증가했고, 110$0^{\circ}C$에서 1시간 동안 나노탄소섬유의 열처리를 통하여 복합재의 전기전도도는 5~7배 증가하였으며, 전자파 차폐율은 2~3 dB 정도 향상시킬 수 있었다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2A
• /
• pp.289-295
• /
• 2008

The purpose of this study was to examine the flexural behavior of reinforced concrete beams strengthened with CFRP strips. A total of 12 rectangular beams were tested. Test variables in this study were the shapes, bonded length and the number of longitudinal layers of CFRP strips. From the experimental study, flexural capacity of the beams strengthened with CFRP strips significantly increased compared to the reinforced concrete beam without a CFRP strip. Maximum increase of ultimate strength was found about 120% more than the control beam. In this test, most of the strengthened beams failed suddenly due to the debonding of CFRP strips. It is also observed that the debonding of the strip was initiated in the flexural zone of the beam and propagated rapidly to the end of the beam. The ultimate tensile strains of CFRP strips in this test were occurred at the level of 36% of rupture tensile strength of the CFRP strip, and an analytical approach to compute the flexural strength of reinforced beams strengthened with CFRP strips based on the effective stresses was conducted.

• Composites Research
• /
• v.31 no.6
• /
• pp.299-303
• /
• 2018

In order to improve the interfacial bonding force and reaction polymerization degree of the carbon fiber reinforced nylon 6 composite material, the surface of the existing epoxy-sizing carbon fiber was desized to remove the epoxy and treated with urethane, nylon and phenoxy sizing agent, was observed. The interfacial bond strength of the resized carbon fiber was confirmed by IFSS (Interfacial Shear Strength) and the fracture surface was observed by scanning electron microscope. The results showed that the interfacial bonding strength of the carbon fiber treated with nylon and phenoxy sizing agents was higher than that of urethane - based sizing. It has been found that the urethane - type resizing carbon fiber has lower interfacial bonding strength than the conventional epoxy - sizing carbon fiber. This result shows that the interfacial bonding between carbon fiber and nylon 6 is improved by removing low activity and smoothness of existing carbon fiber.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.6 s.22
• /
• pp.212-217
• /
• 2004

Carbon fiber reinforced plastic(CFRP) plate Is one of the alterative materials for soengthening of reinforced and prestressed connote members due to excellent strength and light weight In this paper, the behavior of beams strengthened with CFRP plate and CFS(Carbon fiber sheet) is observed and analyzed from the test results. Especially specimens with thick plate is tested when large moment and large shear lone appear in same position. The main failure mode is a peeling-off of the CFRP plate near the loading points due to flexural-shear crack, Because of this failure mode, failure load is not linearly proportional to the thickness of CFRP plates. When beam is wrapped with CFS around oかy loading point it does not influence on the failure loads. Depending on the loading pattern, it is necessary to consider different design criteria for reinforced concrete members with external reinforcement. When line moment and large shear force appear in same location, maximum thickness may limit to 0.6mm and ratio between moment of strengthened beam and moment of unstrengthened beam is proposed 1.5-2.0. In order to use the plate of thicker than 6mm, CFS may be extended to the location which moment of strengthened beam is 1.5 times than moment of unstrengthened beam.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.176-181
• /
• 1990

For the purpose of the improvement of interfacial shear strength in carbon fiber/aluminum matrix composite material, polyacrylonitrile-based carbon fibers were surface treated by hydrogen sulfide gas continuously between 400 and $600^{\circ}C$. Surface treated carbon fibers were analysed by scanning electron microscope. The existence of sulfur compound on treated carbon fiber surfaces was confirmed, and carbon and oxygen contents of the fiber surfaces were examined by X-ray photoelectron spectroscopy. Optimum treating temperature for the adsorption of sulfur on the carbon fiber surface was $500^{\circ}C$. Sulfur compounds on the carbon fiber surfaces form the structures of disulfide, $(S)_n$ and thiophene. The decrease in the tensile strength of the carbon fibers was observed less than about 5%.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.337-345
• /
• 2009

The purpose of this study is to investigate the shear strengthening effectiveness of the beams strengthened with near surface mounted (NSM) and external bonded (EB) CFRP strips. A total of nine concrete beams were made and tested. From this study, it was found that the shear stiffness and strength of the beams strengthened with NSM and EB strips were significantly improved compared to the control beam. Failure of the beam strengthened with NSM and EB strips was initiated by shear cracks, propagated diagonally to the adjacent epoxy grooves without crossing the epoxy and finally sudden diagonal crack connecting the point of application of load and flexural crack was occurred. For the beam strengthened combined with NSM and EB CFRP strips, the tensile strains in the NSM CFRP strips were observed in the range of 0.35% to 0.45% and strains with EB strips were measured about 0.3%.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.75-75
• /
• 2012

탄소섬유는 전구체의 종류에 따라 PAN계, 피치계 그리고 레이온계로 나뉘며 최종 탄소섬유의 특성에도 차이가 있는 것으로 알려져 있다. 최근에는 PAN계 탄소섬유가 세계 시장의 대부분을 차지하고 있으며, PAN계 탄소섬유의 초경량, 고강도, 고탄성, 내약품성 그리고 열안정성 등의 우수한 특성으로 최첨단 고기능성 제품의 복합재로 많이 이용되고 있다. 그러나 탄소섬유가 가지고 있는 높은 열전도성은 적용에 따라 단점으로 작용될 수도 있다. 예를 들면, 로켓 엔진의 노즐이나 원자로의 구조물 그리고 극한조건용 구조재료 등, 고강도 단열특성을 요하는 최첨단 복합재로 응용 범위를 넓히는데 한계로 작용한다. 레이온은 최초의 탄소섬유 전구체였으나 공정상 경제성이 떨어지는 이유로, 지금은 고탄성을 요구하는 특수 목적으로만 소량 생산되고 있다. 레이온의 주원료는 셀룰로오스이며 셀룰로오스는 지구상에서 가장 흔한 재료이므로 오늘날 셀룰로오스를 보강재로 이용하려는 연구가 활발히 진행되고 있다. 본 연구에서는 탄소섬유의 열전도도를 낮추기 위한 방법으로 안정화셀룰로오스를 첨가한 PAN용액을 출발물질로 탄소섬유를 제조하고 특성 연구를 진행하였다. PAN용액에 셀룰로오스의 분산성을 향상시키기 위해 셀룰로오스를 열처리하였다. 이 과정에서 얻어진 안정화 셀룰로오스의 수율을 높이기 위해 셀룰로오스를 난연 처리하였으며, 그 결과 안정화셀룰로오스의 수율을 향상시킬 수 있었다. 안정화셀룰로오스를 첨가시킨 PAN계 탄소섬유의 물리적, 기계적 그리고 열적 특성을 SEM, XRD, 만능 인장시험기, TGA 그리고 Laser Flash Method 등을 통해 주요 특성 및 변화를 관찰한 결과, 순수한 PAN계 탄소섬유의 특성과 유사한 결과를 얻었다. 향후 몇 가지 공정상의 문제점을 개선한다면 흥미로운 결과를 기대할 수 있을 것으로 본다.