• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.123-127
• /
• 2005

Surface refraction and crosswell seismic survey conducted as a part of geoscientific studies applied in an area of ground water reservoir shows that, 1) the average velocity with respect to depth is about 250 m/s for the surface layer (<4m), 2,500 m/s for the weathered formation, and greater than 3,500 m/s for the bed rocks, 2) the depth to the bedrock derived from the seismic studies and the sonic log (17m) is somewhat different from the depth obtained from the core study (25m).

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.291-296
• /
• 2006

The aspect of wave propagation around cavity was investigated for the exact inversion of crosshole tomography data in order to understand the possibility of the existence of underground cavity. We found that the adequate frequency range for the tunnel investigation was about 2kHz to 5kHz, and the grid space was set up to 1/10 length of wavelength. The propagation of the seismic wave near the cavity may go through or detour the cavity according to the seismic velocity of inside of cavity. The detouring wave propagates with the seismic velocity of mother rock in spite of the velocity of inside of cavity. The smaller the velocity difference between the mother rock and cavity, the more frequent penetration of the seismic wave through the cavity was appeared.

• Geophysics and Geophysical Exploration
• /
• v.17 no.4
• /
• pp.231-241
• /
• 2014

Recently, single channel seismic survey for engineering purpose have been used widely taking advantage of simple processing. However it is very difficult to obtain high fidelity subsurface image by single channel seismic due to insufficient fold coverage. Recently, seismic waveform inversion in multi channel seismic survey is utilized for accurate subsurface imaging even in complex terrains. In this paper, we propose the seismic waveform inversion algorithm for velocity model building using a single channel seismic data. We utilize the Gauss-Newton method and assume that subsurface model is 1-Dimensional. Seismic source estimation technique is used and offset effect is also corrected by removing delay time by offset. Proposed algorithm is verified by applying modified Marmousi2 model, and applied to field data set obtained in port of Busan.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2004.06a
• /
• pp.88-93
• /
• 2004

본 논문에서는 현장에서 획득한 2차원 탄성파 탐사 자료를 처리하는 시스템을 제안한다. 일반적으로 탐사 자료는 매우 방대하여 효율적인 자료 처리 및 관리 시스템은 필수적이라고 할 수 있다. 본 논문에서는 모듈의 처리 과정에서 QC(Quality of Control)를 쉽게 하기 위해 윈도우 기반 GUI 환경을 제공할 뿐만 아니라, 모듈의 처리 흐름과 파라미터를 저장할 수 있는 템플릿 개념을 소개한다. 또한 객체 지향 개념을 도입하여 모듈들의 삽입, 삭제가 용이한 장점을 가지고 있다. 개발 환경은 MFC를 바탕으로 Windows 운영체제에서 개발되었다. 본 논문에서 개발된 시스템은 탄성파를 이용한 지반 조사에 효율적으로 사용될 수 있다고 사료된다.

• Geophysics and Geophysical Exploration
• /
• v.5 no.3
• /
• pp.145-149
• /
• 2002

The static correction, which is classified into refraction based static correction and reflection based residual static correction, removes distortions caused by irregularities of thickness or velocity in near-surface. Generally, refraction statics is a time consuming process because of high dependence on the interpreter's analysis. Therefore, for huge 3D seismic data, automatic static correction which minimizes the interpreter's analysis is required. In this research, we introduce an efficient method of refraction static correction for land 3D seismic survey.

• Geophysics and Geophysical Exploration
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2010

Seismic reflection surveying is one of the most widely used and effective techniques for coal seam structure delineation and risk mitigation for underground longwall mining. However, the ability of the method can be compromised by the presence of volcanic cover. This problem arises within parts of the Bowen and Sydney Basins of Australia and seismic surveying can be unsuccessful. As a consequence, such areas are less attractive for coal mining. Techniques to improve the success of seismic surveying over basalt flows are needed. In this paper, we use elastic wave-equation-based forward modelling techniques to investigate the effects and characteristics of seismic wave propagation under different settings involving changes in basalt properties, its thickness, lateral extent, relative position to the shot position and various forms of inhomogeneity. The modelling results suggests that: 1) basalts with high impedance contrasts and multiple flows generate strong multiples and weak reflectors; 2) thin basalts have less effect than thick basalts; 3) partial basalt cover has less effect than full basalt cover; 4) low frequency seismic waves (especially at large offsets) have better penetration through the basalt than high frequency waves; and 5) the deeper the coal seams are below basalts of limited extent, the less influence the basalts will have on the wave propagation. In addition to providing insights into the issues that arise when seismic surveying under basalts, these observations suggest that careful management of seismic noise and the acquisition of long-offset seismic data with low-frequency geophones have the potential to improve the seismic results.

• Tunnel and Underground Space
• /
• v.27 no.4
• /
• pp.230-242
• /
• 2017

Seismic velocities measured from in-situ tests (n=177) and through rock core samples (n=1,035) are reviewed in light of construction standards, widely used standards as a first-hand approximation of rock classification solely based on seismic velocities. In-situ down hole tests and refraction survey for soft rocks showed seismic velocities of 1,400~2,900 m/s which is faster than those specified in construction standards. For moderate~ hard rocks, in-situ down hole tests and refraction survey showed 2,300~3,800 m/s which roughly corresponds with the range specified in the construction standards. A similar trend is also observed for seismic velocities measured from rock core samples. The observed differences between construction standards and seismic velocities can be explained in two ways. If construction standards are correct the observed differences may be explained with seismic velocities affected by underlying fast velocities and also possibly with selection of intact cores for velocity measurement. Alternatively, construction standards may have intrinsic problems, namely artificial discrete boundaries between soft rocks and moderate rocks, application of foreign standards without consideration of geologic setting and lack of independent verification steps. Therefore, we suggest a carefully designed verification studies from a test site. We also suggest that care must be exercised when applying construction standards for the interpretation and accessment of rock mass properties.

• Geophysics and Geophysical Exploration
• /
• v.12 no.2
• /
• pp.173-182
• /
• 2009

In April 2008, KIGAM carried out an ocean-bottom seismometer (OBS) survey in the central Ulleung Basin where strong bottom simulating reflectors (BSRs) were revealed from previous surveys and some gas-hydrate samples were retrieved by direct sampling. The purpose of this survey is to estimate the velocity structure near the BSR in the gas hydrate prospect area using wide-angle seismic data recorded on the ocean-bottom seismometers. Along with the OBS survey, a 2-D seismic survey was performed whereby stratigraphic and preliminary velocity information was obtained. Two methods were applied to wide-angle data for estimating P wave velocity; one is velocity analysis in the $\tau$-p domain and the other is seismic traveltime inversion. A 1-D interval velocity profile was obtained by the first method, which was refined to layered velocity structure by the latter method. A layer stripping method was adopted for modeling and inversion. All velocity profiles at each OBS site clearly show velocity reversal at BSR depths due to the presence of gas hydrates. In addition, we could confirm high velocity in the column/chimney structure.

• Geophysics and Geophysical Exploration
• /
• v.27 no.2
• /
• pp.91-107
• /
• 2024

Single-channel seismic exploration has proven effective in delineating subsurface geological structures using small-scale survey systems. The seismic data acquired through zero- or near-offset methods directly capture subsurface features along the vertical axis, facilitating the construction of corresponding seismic sections. However, substantial noise in single-channel seismic data hampers precise interpretation because of the low signal-to-noise ratio. This study introduces a novel approach that integrate noise reduction and signal enhancement via matrix rank optimization to address this issue. Unlike conventional rank-reduction methods, which retain selected singular values to mitigate random noise, our method optimizes the entire singular value spectrum, thus effectively tackling both random and erratic noises commonly found in environments with low signal-to-noise ratio. Additionally, to enhance the horizontal continuity of seismic events and mitigate signal loss during noise reduction, we introduced an adaptive weighting factor computed from the eigenimage of the seismic section. To access the robustness of the proposed method, we conducted numerical experiments using single-channel Sparker seismic data from the Chukchi Plateau in the Arctic Ocean. The results demonstrated that the seismic sections had significantly improved signal-to-noise ratios and minimal signal loss. These advancements hold promise for enhancing single-channel and high-resolution seismic surveys and aiding in the identification of marine development and submarine geological hazards in domestic coastal areas.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.524-527
• /
• 2007

남극 반도 북부해역은 남극대륙 주변부에 존재하는 가스하이드레이트 매장 유망지역중의 하나이다. 남극반도 북부해역내에서 BSR이 가장 뚜렷이 나타나는 남셰틀랜드 군도의 대륙주변부에서 가스하이드레이트 특성 및 분포를 연구하기 위한 탄성파 탐사가 1992년, 2005년도 수행되었다. 이 지역에 나타나는 BSR은 대륙사면에서 광범위하게 발달되어있다. 이 지역 BSR에 대한 AVO 분석결과에 의하면 BSR상부지층은 높은 탄성파 속도를 갖으며 하부지층은 가스를 포함하는 것으로 밝혀졌다. 탄성파 단면에 나타난 BSR의 발견지역을 대상으로 분포도를 작성하였으며, 이 지역에 대한 추가적인 탄성파 탐사 완료 후에는 정확한 매장량과 분포가 밝혀질 것이다.