• 한국재료학회지
• /
• 제10권10호
• /
• pp.703-708
• /
• 2000

최근에 상용차용 디젤 엔진의 성능 향상을 목적으로 엔진 설계가 급격히 변화되면서 캠 팔로우어(cam follower)와 캠(cam) 사이에 작용하는 접동면 하중의 증가로 접동면에서의 마모가 중요한 문제가 되고 있다. 본 연구에서는 기존의 주절체 및 소결합금 캠 팔로우어에 비해 내마모성이 우수한 세라믹 캠 팔로우어를 개발하였다. 잔류 응력을 완화시켜주는 중간층을 사용하지 않고 질화규소($Si_3N_4$) 팁과 중탄소강을 활성납재를 사용하여 직접 접합후 냉각시키는 과정에서 두 모재의 열팽창계수차에 의한 크라우닝(crowning, R) 이 형성되도록 하였다. 접합에 사용한 중탄소강은 열팽창시 이력(hysteresis) 거동을 나타내었으며, $A_{c1}$ 변태점인 $723^{\circ}C$ 이하에서 접합할 경우 원하는 크라우닝이 형성되었다. 접합온도가 $723^{\circ}C$ 이상이 되면 크라우닝 (R) 값이 온도에 따라 지수함수적으로 증가하였으며 이는 중탄소강의 상변태에 의한 열팽창.수축의 이력 특성으로 설명되어질 수 있었다. 규격에 맞는 크라우닝이 형성되는 최적 접합 온도는 $700~720^{\circ}C$의 범위였다. 질화규소와 중탄소강의 직접 접합방법으로 접합과 동시에 크라우닝을 형성시키고 제어함으로써 난가공재인 세라믹을 곡면 가공하지 않고도 적당한 곡률을 갖는 저가의 세라믹 캠 팔로우어를 제조할 수 있었다.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.38-42
• /
• 2009

Gear is an essential component of an automotive. Crowning is used for tooth modification of a gear. The basic concept of gear tooth crowning is to reduce the stress concentration in edge of contact area and appropriate profile modifications can help gears to resist scoring, pitting, and tooth breakage. In this study, a method to determinate spur gear tooth crowning amount to make smooth surface stress and subsurface stress distribution is proposed. This method is based on the contact analysis.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.527-528
• /
• 2008

• 한국소음진동공학회논문집
• /
• 제23권2호
• /
• pp.185-191
• /
• 2013

This paper presents a new method for roller design of IRB(isolation roller bearing) seismic isolation device using experimental evaluation. Three layered plate is adopted for the IRB in which the upper plate is placed on x direction and the lower plate is placed on y direction. The rollers placed in each plate make a plate movement. The roller is then optimally designed using variable geometric conditions. Stress distribution depends on the diameter and length of the roller and hence this is used for the determination of optimal geometry of the roller. In the experimental evaluation, it is observed that stress concentration at the end sides of roller is decreased and geometric coefficients depend on crowning dimension. In addition, in order to determine optimal design parameters of the roller the plastic deformation and friction are experimentally identified.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.162-168
• /
• 2002

This paper shows the failure(wear) phenomena of differential bearings in the transaxle of passenger cars and investigate their characteristics. It was found that the wear mechanism was mild abrasive wear caused by the presence of particles in the gear box. The sides of the outer raceway was more neared than center of it, so it is showed as if the crowning of outer raceway are increased. With close examination of the failed bearing, various countermeasures could be suggested.

• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.40-49
• /
• 2010

Conical involute gears are being used for marine gearboxes, automotive transmissions, and robots, and so on, but not much. As involute profile gear, conical involute gear not only can be engaged with spur and helical gear but also can be used for power transmission of parallel, crossed and skewed axis with small angle. Hence, conical involute gears are likely to develop in future. Through a study on the basic theory of conical involute gear, tooth surface compressive stress analysis was performed by using commercial modeling program, comparing before and after profile modification. As a result, it noticed that tooth profile modification is able to relieve more tooth surface compressive stress than before modification.

• 한국정밀공학회지
• /
• 제17권11호
• /
• pp.199-205
• /
• 2000

The vibration and noise of gears is due to the vibration exciting force caused by the tooth stiffness which changes periodically as the mesh of teeth proceeds and by the transmission error, that is, the rotation delay between driving gear and driven gear caused by manufacturing error and alignment error in assembly and so on. The purpose of this study is to develop how to calculate simultaneously the optimum amounts of tooth profile modification, end relief and crowning by minimizing the vibration exciting force of helical gears. We estimate the vibration exciting force by the mesh analysis of gears. The constraints of this problem consist of contact ratio and strengths of gear teeth such as tooth fillet stress, surface durability and scoring. ADS(Automated Design Synthesis) is used as an optimization tool. And, since the aspect ratio is an important parameter of tooth modification, we investigate the relation between it and the optimum values of tooth modification. The proposed method can calculate the optimum amount of tooth modification automatically and is to be utilized to resolve the problem of vibration of helical gears.