• Journal of Korean Association for Spatial Structures
• /
• v.7 no.4
• /
• pp.89-96
• /
• 2007

The fundamental frequency maximization of beam structures is carried out by using strain energy based topology optimization technique. It mainly uses the modal strain energy distributions induced by the mode shapes of the structures. The modal strain energy to be minimized is employed as the objective function and the initial volume of structures is adopted as the constraint function. The resizing algorithm devised from the optimality criteria method is used to update the hole size of the cell existing in each finite element. The beams with three different boundary conditions are used to investigate the optimum topologies against natural mode shapes. From numerical test, it is found to be that the optimum topologies of the beams produced by the adopted technique have hugh increases in some values of natural frequencies and especially the technique is very effective to maximize the fundamental frequency of the structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.40-45
• /
• 2013

The purpose of this study was to detect the pin hole defect of dental composite restoration using lock-in thermography method. Amplitude and phase images of the composite resin specimens were analyzed according to the lock-in frequency and the diameter of defect area. Through the amplitude image analysis, at lock-in frequency of 0.05 Hz, defect diameters 2-5 mm exhibited the highest amplitude contrast value between defective area and sound area. The lock-in frequency range of 0.3-0.5 Hz provided good phase angle contrast for the defect area. At lock-in frequency range of 0.5 Hz, defect diameter of 5 mm exhibited the highest phase contrast value. It is concluded that the infrared lock-in thermography method verified the effectiveness for detecting the pin hole defect of dental composite restoration.

• Journal of Korean Association for Spatial Structures
• /
• v.5 no.3 s.17
• /
• pp.83-89
• /
• 2005

This paper provides the results of the investigation on the optimum topology of simply supported deep beam structures with multi-point load cases. In this study, the strain energy to be minimized is considered as the objective function and the initial volume of structures is used as the constraint function. The resizing algorithm based on the optimality criteria is adopted to update the hole size existing inside the material. In this study, the sensitivities of topology optimization parameters to the optimum topology of the deep bean structures is investigated and also the effect of filtering process on the optimum topology is thoroughly tested. From numerical tests, the optimum topology of the deep beam is closely related with the optimization parameters used in the iteration and the filtering process play important role in order to find the optimum topology of the deep beam.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.91-97
• /
• 2010

This paper proposes method to evaluate the location and size of the internal defects of metallic specimens by the shearing phase lock-in infrared thermography. Until now, infrared thermography test for metal specimen of STS304 and Cu-Zn were conducted to find the best test conditions. However, In unspecified situation of the form and existence of defects, there was a disadvantage to takes a long time for finding the optimal experimental conditions. The defect detection and evaluation was performed at 60 MHz signal using lock-in and shearing-phase method under limited heating conditions. By shearing-phase distribution method, Defects for the maximum, minimum and zero points were quantitatively detected at the size and location of the subsurface. As results, application of the proposed technique was verified for STS304 and Cu7-Zn3 with artificial defect and factors affected defect evaluation were searched and analyzed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.4
• /
• pp.459-466
• /
• 2020

The sound collected through the multi-rotor unmanned aerial vehicle (UAV) includes the ego noise generated by the motor or propeller, or the wind noise generated during the flight, and thus the quality is greatly impaired. In a multi-rotor UAV environment, both the magnitude and phase of the target sound are greatly corrupted, so it is necessary to enhance the sound in consideration of both the magnitude and phase. However, it is difficult to improve the phase because it does not show the structural characteristics. in this study, we propose a CNN-based complex spectrogram enhancement method that removes noise based on complex spectrogram that can represent both magnitude and phase. Experimental results reveal that the proposed method improves enhancement performance by considering both the magnitude and phase of the complex spectrogram.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.7
• /
• pp.1552-1558
• /
• 2011

In this paper, a dual-loop Integer-N phase-delay locked loop(P DLL) architecture has been proposed using a low power consuming voltage controlled delay line(VCDL). The P DLL can have the LF of one small capacitance instead of the conventional second or third-order LF which occupies a large area. The proposed dual-loop P DLL can have a small gain VCDL by controlling the magnitude of capacitor and charge pump current on the loop of VCDL. The proposed dual-loop P DLL has been designed based on a 1.8V $0.18{\mu}m$ CMOS process and proved by Hspice simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12C
• /
• pp.1149-1155
• /
• 2007

In this paper, we propose a new overlap and add speech synthesis method which demonstrates improved continuity performance. The proposed method uses a weighted phase error function and minimizes the wave discontinuity of the synthesis signal, rather than the phase discontinuity, to estimate the mid-point phase. Experimental results show that the proposed method improves the continuity between the synthesized signals relative to the existing method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.4
• /
• pp.37-44
• /
• 2009

A novel phase-locked loop(PLL) architecture with resistance and capacitance scaling scheme has been proposed. The proposed PLL has three charge pumps. The effective capacitance and resistance of the loop filter can be scaled up/down according to the locking status by controlling the direction and magnitude of each charge pump current. This architecture makes it possible to have a narrow bandwidth and low resistance in the loop filter, which improves phase noise and reference spur characteristics. It has been fabricated with a 3.3V $0.35{\mu}m$ CMOS process. The measured locking time is $25{\mu}s$ with the measured phase noise of -105.37 dBc/Hz @1MHz and the reference spur of -50dBc at 851.2MHz output frequency

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.5
• /
• pp.67-74
• /
• 2007

The unsymmetrically layered artificial material model is consistently introduced to find the optimum topologies of the plate structures. Reissner-Mindlin (RM) plate theory is adopted to formulate the present 9-node plate element considering the first-order shear deformation of the plates. In the topology optimization process, the strain energy to be minimized is employed as the objective function and the initial volume of structures is adopted as the constraint function. In addition, the resizing algorithm based on the optimality criteria is used to update the hole size introduced in the proposed artificial material model. Several numerical examples are rallied out to investigate the performance of the proposed technique. From numerical results, the proposed topology optimization techniques are found to be very effective to produce the optimum topology of plate structures. In particular, the proposed unsymmetric stiffening layer model make it possible to produce more realistic stiffener design of the plate structures.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1172-1180
• /
• 1998

Elastic wave scattering from an acoustically rigid or soft object is studied and compared with the acoustic wave scattering. The behavior of phases as well as magnitudes of partial waves and their total summation of scattered wave are numerically analyzed and discussed. The effect of mode conversion, which occurs between longitudinal and transversal waves in elastic wave scattering. on the magnitudes and phases of scattered waves is identified.