• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.21-26
• /
• 1999

In this study, to assess chip breaking characteristics of cold-drawn free machining steels, a newly developed non-dimensional parameter, chip breaking index, C/sub B/ has been adopted. And for comparison with free machining steels, chip breaking characteristics of conventional carbon steels were investigated. Properly controlled chips were produced with the C/sub B/ value of 0.05∼0.2, regardless of steel types. In case of cold-drawn free machining steels, however, cycle times of chip breaking are relatively shorter than those of conventional steels. And properly controlled chips were obtained from wider range of feed rate.

• 한국생산제조학회지
• /
• 제8권4호
• /
• pp.45-51
• /
• 1999

In this study to assess chip breaking characteristics of cold-drawn free machining steels a newly developed non-dimensional parameter chip breaking index CB has been adopted. And for comparison with free machining steels chip breaking characteristics of conventional carbon steels were investigated. Properly controlled chips were produced with the CB value of 0.05-0.2 regardless of steel types. In case of cold-drawn free machining steels however cycle times of chip breaking are relatively shorter than those of conventional steels. And properly controlled chips were obtained from wider range of feed rate.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.198-203
• /
• 1999

In this study, chip-tool friction and shear characteristics of cold drawn free machining steels in turning were assessed. To do this, a newly developed equivalent oblique cutting model was adopted. And for comparison with those of free machining steels, chip-tool friction and shear characteristics of conventional carbon steels were also investigated. The Pb-S free machining steel shows superior machinability to others. In case of the Bi-S free machining steel, the shear stress and the specific friction energy are relatively lower than those of conventional carbon steels, but its shear strain is relatively high, so it does not show any remarkable improvement of machinability.

• 한국기계가공학회지
• /
• 제4권2호
• /
• pp.3-9
• /
• 2005

In this study, the chip breaking characteristics of S, PbS and BiS free machining steels have been assessed. PbS free machining steel shows the lowest value of chip thickness ($t_c$) under the same cutting conditions. SM10C steel has the largest value of the chip cross-section area ratio ($R_{CA}$). As the feed rate becomes larger the chip breaking cycle time ($T_B$) decreases and the chip breaking index ($C_B$) increases. The properly controlled-C type chip has been obtained with the value of $C_B$ between 0.05 and 0.2. Free machining steel, PbS produces the properly controlled-C type chip in a wider feed rate range than other steels.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.48-54
• /
• 2000

In this study the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison those of the cold drawn Pb-S free machining steel the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation chip cross-section area ratio is introduced. The chip cross-section area ratio is defined as chip cross-section area is divided by undeformed chip cross-section area. The variational patters of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress however seems to be dependent on the carbon content of the materials. The cold drawn Bi-S and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of free machining inclusions such as MnS Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.351-356
• /
• 1999

In this study, the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison, those of the cold drawn Pb-S free machining steel, the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation, the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation, 'chip cross-section area ratio' is introduced. The chip cross-section area. The variational patterns of cross-section area is divided by undeformed chip cross-section area. The variational patterns of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress, however, seems to be dependent on the carbon content of the materials. The cold drawn BiS and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of non-metallic inclusions such as MnS, Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• 대한기계학회논문집
• /
• 제9권6호
• /
• pp.757-766
• /
• 1985

본 연구에서는 기계공업 분야에서 많이 이용되는 구조용 합금강인 Cr-Mo강 (SCM4)과 쾌삭강(SUM31, SUM24L)과의 이종강봉 마찰용접에서 소성변형중에 발생된 초 기 AE량과 용접 품질(강도)제어 사이에 역시 정량적 상관성이 성립함을 용접 회전수, 용접에너지, 용접 업셋 및 용접 시간 등을 매개 변수로 하여 실험과 계산을 통해 입증 하고, 이를 상관식의 95% 신뢰성을 확인한 후, 본 연구의 최종 목적으로서, 마찰용접 평가의 자동화가 이루어지게 하였다.