• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.69-75
• /
• 2008

Shear tests were carried out on interface between two concrete eco-blocks which comprise segmental retaining wall. Three interface conditions were considered : 1) direct contact of two blocks, 2) placing rubber pad between two blocks, 3) placing rubber pad and shear key between two blocks. According to shear tests, shear load-shear displacement relationship which was obtained from direct contact of two blocks was similar to elastic-perfectly plastic behavior. Ductile behavior of shear load-shear displacement relationship was observed for the interface condition of placing rubber pad. Apparent minimum shear capacities and apparent friction angles for the interface conditions of direct contact of two blocks, placing rubber pad between two blocks, placing rubber pad and shear key were 1.7 kN/m, $27.6^{\circ}$ and 4.2 kN/m, $26.2^{\circ}$ and 20.9 kN/m, $26.0^{\circ}$ respectively.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.21-28
• /
• 2006

This paper presents both experimental and analytical studies for the development of an ECC(Engineered Cementitious Composites) using ground granulated blast furnace slag(slag). This material has been focused on achieving moderately high composite strength while maintaining high ductility, represented by strain-hardening behavior in uniaxial tension. In the material development, micromechanics was adopted to properly select optimized range of the composition based on steady-state cracking theory and experimental studies on matrix, and interfacial properties. A single fiber pullout test and a wedge splitting test were employed to measure the bond properties of the fiber in a matrix and the fracture toughness of mortar matrix. The addition of the slag resulted in slight increases in the frictional bond strength and the fracture toughness. Subsequent direct tensile tests demonstrate that the fiber reinforced mortar exhibited high ductile uniaxial tension behavior with a maximum strain capacity of 3.6%. Both ductility and tensile strength(~5.3 MPa) of the composite produced with slag were measured to be significantly higher than those of the composite without slag. The slag particles contribute to improving matrix strength and fiber dispersion, which is incorporated with enhanced workability attributed to the oxidized grain surface. This result suggests that, within the limited slag dosage employed in the present study, the contribution of slag particles to the workability overwhelms the side-effect of decreased potential of saturated multiple cracking.

• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.127-136
• /
• 2015

To evaluate the effects of limestone powder and silica fume on the properties of high-strength high-volume ground granulated blast-furnace slag (GGBFS) blended cement concrete, this study investigated the rheology, strength development, hydration and pozzolanic reaction characteristics, porosity and pore size distribution of high-strength mortars with the water-to-binder ratio of 20, 50 to 80% GGBFS, up to 20% limestone powder, and up to 10% silica fume. According to test results, compared with the Portland cement mixture, the high-volume GGBFS mixture had much higher flow due to the low surface friction of GGBFS particles and higher strength in the early age due to the accelerated cement hydration by increase of free water; however, because of too low water-to-binder ratio and cement content, and lack of calcium hydroxide content, the pozzolanic reactio cannot be activated and the long-term strength development was limited. Limestone powder did not affect the flowability, and also accelerate the early cement hydration. However, because its effect on the acceleration of cement hydration is not greater than that of GGBFS, and it does not have hydraulic reactivity unlikely to GGBFS, compressive strength was reduced proportional to the replacement ratio of limestone powder. Also, silica fume and very fine GGBFS lowered flow and strength by absorbing more free water required for cement hydration. Capillary porosities of GGBFS blended mortars were smaller than that of OPC mortar, but the effect of limestone powder on porosity was not noticeable, and silica fume increased porosity due to low degree of hydration. Nevertheless, it is confirmed that the addition of GGBFS and silica fume increases fine pores.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.169-177
• /
• 2016

Sliding slab track system, which consists of low friction sliding layer between track slab and bridge deck, is recently devised to reduce track-bridge interaction effect of continuously welded rail(CWR) without applying special devices such as rail expansion joint(REJ). In this study, a series of track-bridge interaction analyses of a long-span bridge with sliding slab track and REJ are performed respectively and the results are compared. The bridge model includes PSC box girder bridge with 9 continuous spans, and steel-concrete composite girder bridge with 2 continuous spans. The total length of the bridge model is 1,205m, and the maximum spacing between the two fixed supports is 825m. Analyses results showed that the sliding slab track system is highly effective on interaction reduction since lower rail additional axial stress is resulted than REJ application. Additionally, horizontal reaction forces in fixed supports were also reduced compared to the results of REJ application. However, higher slab axial forces were developed in the sliding slab track due to the temperature load. Therefore, track slab section of the sliding slab track system should be carefully designed against slab axial forces.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.87-98
• /
• 1990

The present Study dealt with the earthquake-resistant design of cantilever retaining walls supporting cohesionless soils. With design examples of three different types of cantilever retaining walls, the factors of safety against sliding were computed at various values of horizontal acceleration coefficient and compared with each other. The horizontal inertia effect due to the weights of concrete wall itself and a portion of backfill was taken into account in the analyses, and also Mononobe-Okabe pseudo-static solution method was modified to deal with various states different from limiting equilibrium state. From the analyses of safety against sliding, it was found that a cantilever retaining wall with sloped base was the most efficient type in earthquake resistant design. It was also found that by sloping the base, the width of the base slab could be reduced, resulting in the least volume of concrete, excavation and backfill as compared to the other types of walls. In the case of a cantilever retaining wall with sloped feel, the efficiency similar to that of a wall with sloped base could be expected under static loading as well as at relatively low level of earthquake loading. However, this efficiency became vanished with the increase of horizontal acceleration coefficient, since the rate of reduction in developed earth pressures on the heel became smaller. In addition, the design charts with different soil friction angles as well as with different earthquake resistant design criteria of safety factor against sliding were presented for the design of cantilever retaining walls sith sloped base.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.46-46
• /
• 2015

강우가 지역별 계절별로 편중되어 있는 우리나라는 수자원의 안정적인 확보와 이용을 위해 다양한 형태의 댐을 건설하여 운영하고 있다. 그러나 대부분의 댐건설을 통해 형성된 저수지들은 탁수 장기화 및 녹조 발생 등의 환경, 생태적인 문제를 겪고 있으며, 그에 따른 사회적 우려로 인해 신규댐 건설을 통한 수자원확보는 더 이상 어려운 실정이다. 이러한 문제에 대응하기 위한 대안으로 기존 댐 저수지들(안동호-임하호)의 구조적 연계운영방안이 진행되고 있다. 본 연구의 목적은 2차원 CE-QUAL-W2모형을 활용하여 안동호와 임하호의 구조적 연결에 따른 탁수의 이동과 각 저수지 내에서의 유동 변화를 해석하는데 있다. 저수지 연계 시나리오는 EL. 138 m 위치에 길이 2 km, 직경 5.5 m 의 콘크리트관(마찰계수 0.05)이 안동호 좌안인 임동면 마리와 임하호 우안 망천리를 연결하는 것으로 가정하였다. 모델의 보정은 실측자료가 풍부한 2006년도 수문사상을 대상으로, 개별 저수지에 대해 수행하였고, 탁수 유동 시나리오 해석은 임하호에 심각한 탁수장기화 문제가 발생했던 2002년을 대상으로 댐 연계 탁수모의를 수행하였다. 안동호와 임하호의 댐 앞에서 모의값과 실측값을 오차를 분석한 결과 탁수예측오차는 AME 0.5~24 mg/L, RMSE 0.7~30.2mg/L의 범위로 비교적 실측값을 잘 반영한 것으로 나타났다. 임하댐의 경우 탁수층의 위치와 두께, 그리고 최고 탁도값을 적절히 재현 하였지만, 안동댐은 최고 탁도값 예측에서 다소 오차가 발생하는 것으로 나타났다. 안동호와 임하호 단독 운영시와 연계 운영시의 탁수변화 파악을 위해 초기 홍수사상이 발생한 8월 이후부터 저수지내의 TSS농도 분포를 비교하였다. 안동호의 경우 댐앞지점의 탁수분포는 수온성층구조에 영향을 받아, 단독 운영시(EL. 130 m)보다 연계운영시(EL. 140 m)에 탁수의 중심이 높은 위치에 형성되었다. 단독 운영시 10월 이후에 전도현상으로 인해 침강되지 않은 잔류 탁수층이 저수지 하부로 확산되었지만, 연계 운영시에는 재부상 되어 상층으로 확산되는 것으로 모의되었다. 또한 연계운영시 유량이동으로 인해 안동호의 탁수 댐앞 도달시간이 짧아지는 것으로 나타났다. 반면 임하호는 연계 운영시 안동댐으로 유출이 생기면서 중층에서 탁수량이 저감되는 것으로 모의되었다. 저수지 내 탁수량 분석을 위해 SS 15 mg/L 이상의 잔류 탁수량을 분석한 결과, 연계운영시 안동호의 평균 잔류탁수량 비율은 11.8% 증가, 임하호의 경우 11.7% 감소하였다. 또한, 탁수의 댐하류 방류일수도 SS 15 mg/L 기준 임하호 9일 저감, 안동호는 70일 증가하여 임하호의 탁수가 안동호의 탁수 장기화에 영향을 주는 것으로 나타났다.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.579-588
• /
• 2021

Reinforced earth retaining walls have been widely used in recent years, as they are superior from the landscape perspective than normal concrete retaining walls. However, as reinforced earth retaining walls are made of various materials depending on site, existing design methods cannot secure stability, and a variety of problems have occurred. Studies on the design and stability analysis methods, which are different from existing methods, have been conducted to address these problems. This study conducted a stability investigation using numerical analysis, and blocks of reinforced earth retaining walls were individually applied, which is different from pre-existing numerical analyses. To verify the input values of the numerical analysis when applying individual blocks, real-scale experiments of the friction characteristics between the blocks and the connection properties between the blocks and stiffener were conducted. The applicability of the block conditions, which were the same as those of real sites, was verified through numerical analysis, and will be used for the stability review and design of various combinations of blocks and stiffeners.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.947-953
• /
• 2005

Previous test results showed that the current ASTM(American Standard for Testing and Materials) grip adapter for GFRP(Glass Fiber Reinforced Polymer) rebar was not fully successful in developing the design tensile strength of GFRP rebars with reasonable accuracy. It is because the current ASTM grip adapter which is composed of a pair of rectangular metal blocks of which inner faces are grooved along the longitudinal direction does not take into account the various geometric characteristics of GFRP rebar such as surface treatment, shape of bar cross section as well as physical characteristics such as poisson effect, elastic modulus in the transverse direction and so on. The objective of this paper is to provide how to proportion the optimum diameter of inner groove in ASTM grip adapter to develop design tensile strength of GFRP rebar. The proportioning of inner groove in ASTM grip adapter is based on the force equilibrium of GFRP rebar between tensile capacity and minimum frictional resistance required along the grip adapter. The frictional resistance of grip adapter is calculated based on the compressive strain compatibility in radial direction induced by the difference between diameter of GFRP rebar and inner groove In ASTM grip. All testing procedures were made according to the CSA S806-02 recommendations. From the preliminary test results on round-type GFRP rebars, it was found that maximum tensile loads acquired under the same testing conditions is highly affected by the diameter of inner groove in ASTM grip adapter. The grip adapter with specific dimension proportioned by proposed method recorded the highest tensile strength among them.