• Corrosion Science and Technology
• /
• v.21 no.1
• /
• pp.68-76
• /
• 2022

Several technologies are employed to protect substrates from corrosion and erosion damage. In particular, arc thermal spray coating technology is widely used as anti-corrosive technology for steel and concrete structures and is applied to offshore plants and petrochemical and drilling facilities. In this investigation, solid particle impingement erosion experiments were performed on an arc thermal spraying-coated specimen using 85% Al-14% Zn-1% Zr wire rod in KR-RA steel. This study investigated the effect of fluorosilicone sealing on the erosion resistance characteristics of the thermal spray coating layer. The erosion rates of the thermal spray-coated and sealed specimens were 4.1×10^-4 and 8.5×10^-4, respectively. At the beginning of the experiment, the fluorosilicone sealant was almost destroyed by the impact of the solid particles. The destruction time for the coating layer was 10 minutes for the thermal spray-coated specimen and 13 minutes for the sealed specimens, indicating that the sealed specimens had better erosion resistance characteristics to solid particle impingement.

• Corrosion Science and Technology
• /
• v.21 no.5
• /
• pp.340-347
• /
• 2022

In this research, mixed metal oxide (TiO₂, RuO₂) coating was applied to grade 1 titanium as a bipolar plate for polymer electrolyte membrane fuel cell (PEMFC). Electrochemical experiments were carried out in an aqueous solution of pH 3 (H₂SO₄ + 0.1 ppm HF, 80 ℃) determined by DoE. The air was bubbled to simulate a cathode environment. Potentiodynamic polarization test revealed that corrosion current densities of the titanium substrate and MMO-coated specimen were 0.180 µA/cm² and 4.381 µA/cm², respectively. There was no active peak. After potentiostatic experiment, current densities of the titanium substrate and the MMO-coated specimen were 0.19 µA/cm² and 1.05 µA/cm², respectively. As a result of observing the surface before and after the potentiostatic experiment, cracked dried clay structures were observed without corrosion damage. Both the titanium substrate and the MMO-coated specimen could not satisfy the interfacial contact resistance suggested by the DoE. Thus, further research is needed before they could be applied as bipolar plates.

• Corrosion Science and Technology
• /
• v.22 no.4
• /
• pp.232-241
• /
• 2023

The mechanical properties of the hydrogen valve responsible for supplying and blocking hydrogen gas in a hydrogen fuel cell electric vehicle (FCEV) were researched. Mechanical properties by hydrogen embrittlement were investigated by coating chromium nitride (CrN) and titanium nitride (TiN) on aluminum alloy by arc ion plating method. The coating layer was deposited to a thickness of about 2 ㎛, and a slow strain rate test (SSRT) was conducted after hydrogen embrittlement to determine the hydrogen embrittlement resistance of the CrN and TiN coating layers. The CrN-coated specimen presented little decrease in mechanical properties until 12 hours of hydrogen charging due to its excellent resistance to hydrogen permeation. However, both the CrN and TiN-coated specimens exhibited deterioration in mechanical properties due to the peeling of the coating layer after 24 hours of hydrogen charging. The specimens coated at 350 ℃ presented a significant decrease in ultimate tensile strength due to abnormal grain growth.

• Corrosion Science and Technology
• /
• v.22 no.2
• /
• pp.108-114
• /
• 2023

In this study, anti-corrosion effect was investigated through various electrochemical experiments after applying Al thermal spraying technology to AA5083-H321. Open circuit potential and anodic polarization curves were analyzed through electrochemical experiments in natural seawater. The shape of the surface was observed using a scanning electron microscope (SEM) and a 3D microscope before and after the experiment. Component and crystal structure were analyzed through EDS and XRD. As a result, the surface roughness of AA5083-H321 and the Al thermal sprayed coating layer increased due to surface damage caused by anodic dissolution reaction during the anodic polarization experiment. The corrosion rate of AA5083-H321 was relatively low because the Al thermal spray coating layer contained structural defects such as pores and crevices. Nevertheless, the open circuit potential of the Al thermal spray coating layer in natural seawater was measured about 0.2 V lower than that of AA5083-H321. Thus, a sacrificial anode protection effect can be expected.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.743-750
• /
• 2023

Aluminum alloy is a material widely used in the aircraft industry. However, since it has relatively low hardness, strength and tribological properties, it is necessary to improve these properties. In this paper, a TiN thin film was coated on the surface of AL7075-T7351 using DC magnetron sputtering. The coating was performed by setting different deposition pressure, deposition time, and applied power. Then, the tribological properties of the thin film were investigated. As a result of the experiment, the hardness of the thin film was higher than that of the base material, and the specimen with the highest hardness had excellent friction coefficient, wear amount, and adhesive strength characteristics. Through this study, it was confirmed that the tribological characteristics of aluminum alloy can be improved by depositing thin films using DC magnetron sputtering.

• Corrosion Science and Technology
• /
• v.23 no.3
• /
• pp.235-245
• /
• 2024

DLC coatings have been widely applied in industrial fields that require high corrosion resistance due to their excellent mechanical characteristics and chemical stability. In this research, effects of DLC coating thickness and defects on corrosion resistance were investigated for application of metallic bipolar plates in polymer membrane electrolyte fuel cells (PEMFCs). Results revealed that a DLC coating thickness of 0.7 ㎛ could lead to a defect size reduction of about 75.9% compared to that of 0.3 ㎛.As a result of potentiodynamic polarization experiments, the current density under a potential of 0.6 V was measured to be less than 1 ㎂/cm²,which was an excellent value. Inparticular, the delamination ratio and the decrease rate of maximum pitting depth were up to 84.8% and 63.3%, respectively, with an increase in the DLC coating thickness. These results demonstrate that DLC coating thickness and defects are factors that can affect corrosion resistance of DLC coating and its substrate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.208-208
• /
• 2009

최근 광섬유 센서기술의 수요는 전 산업분야에 걸쳐 높아지고 있으며, 이에 비례하여 기업 간, 국가 간 경쟁이 첨예화되고 있다. 또한 소형화, 경량화, 고성능화 센서에 대한 요구도 높아지고 있어 종래의 각종 센서들의 형태와 개선을 위한 연구개발이 매우 활발하게 전개되고 있으므로 이를 대체할 수 있는 광섬유 센서의 수요가 급격히 늘어날 전망이다. 기존 침입자 감지 시스템은 태풍, 낙뢰, 폭설, 폭우 등의 기상변화나 지반 흔들림, 통행차량 진동 및 전자기 간섭 등에 영향을 받아 오작동, 오경보가 빈번히 발생된다. 이러한 문제의 해결책으로 광섬유 센서 케이블을 이용한 시스템이 대안으로 부각되고 있다. 현재 국내에서 군부대, 공항을 중심으로 펜스와 휴전선 철책에 힘입자 감지를 위하여 도입되고 있다. 광섬유 센서 케이블을 사용하는 광망경비시스템은 광섬유 센서 케이블을 그물망 형태(광망)로 만들어 경계 지역에 설치된다. 광망경비시스템의 원리는 광섬유에 광펄스를 입사시켜 순환시키는데 침입자가 광망을 절단하거나 외력을 가할 경우 발생되는 레일리 산란에 기인하는 후방산란과 접속점과 파단점에서 생기는 반사광을 OTDR(Optical Time Domain Reflectometer)로 검출하여 침입상황 및 침입위치를 탐지한다. 그러나 이러한 침입자 감지를 위한 광망경비시스템의 핵심부품인 광섬유 센서 케이블은 기존에 전량 해외수입에 의존하고 있는 실정이며, 지금까지 국내에서 생산하기 위한 제작 기술과 노하우가 초보단계에 머물러 있다. 이러한 광섬유 센서 케이블 제작에 있어서 중요한 부분이 패키징 기술이라 할 수 있다. 이는 광섬유 센서를 일반적인 피복 구조로 패키징하게 되면, 센서 고유의 특성이 패키징 과정과 운반과정, 포설과정에서 변하게 되고 센서로써의 신뢰성이 크게 저하된다. 본 연구에서는 힘입자 감지용 광섬유 센서 케이블의 설계와 제작을 위한 제조공법을 확립하고, 이를 이용해 제작된 광섬유 센서 케이블의 신뢰성 특성을 평가하였다. 설계 제작된 광섬유 센서 케이블의 구조는 멀티모드광섬유(MMF) 에 0.9 mm Tight buffer를 코팅하고, 광심선 주위에 아라미드 얀을 삽입시킨 후 고문자 수지를 적용하여 외부 피복 (jacket)을 하였다. 제작된 광섬유 센서 케이블의 외경 측정결과 기준치 ($2.95\;{\pm}\;0.03$ mm)를 모두 만족하였고, 850 nm 파장에서의 광 손실 측정 결과 4.0 dB/km 이하였다. 또한 주요 항목의 신뢰성 특성 시험결과, 인장강도는 8~10 kg의 인장력을 갖으며 온도순환시험 ($-30^{\circ}C\;{\sim}\;+75^{\circ}C$)에서의 광 손실은 0.6 dB 이하로 나타나 침입자 감지용 광섬유 센서 케이블로 적합함을 확인할 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.37-41
• /
• 2018

This paper presents the integrated fluorescent oxygen sensor probe module based on planner lightwave circuits using UV imprint lithography. The oxygen sensor system is consisted of the optical source part, optical detector part and optical sensing probe part to be composed of the planner lightwave circuit and oxygen sensitive thin film layer. Firstly, we optimally designed the planner lightwave circuit with asymmetric $1{\times}2$ beam splitter using beam propagation method. Then, we fabricated the planner lightwave circuits using UV imprint lithography process. This planner lightwave circuits transmitted the optical power with 76% efficiency and the fluorescence signal with 70% efficiency. The oxygen sensitive thin film layer is coated on the end face of planner lightwave circuit. The oxygen sensor system using this sensor probe module with planner lightwave circuit could measure the concentration with 0.3% resolution from 0% to 20% gas range. This optical oxygen sensor probe module make it possible to compact, simple and cheap measurement system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.102-105
• /
• 2005

가스센서는 응용 분야와 기능 및 종류가 다양하고 최첨단 분야로서 학문적으로는 물리, 화학, 전기, 전자 및 기계 등의 배경을 필요로 하며 산업적으로는 공업 전 분야와 농림, 축산, 사무기기에서 뿐만 아니라 공해 방진용(자동차 연소제어 및 배출가스 제어, 대기오염 감시등), 민생용(조리, 환기, 공조 등), 교통 보안용(음주운전측정 및 음주운전 방지장치 등), 방재용(가스 누설 탐지기, 불완전 연소 방지, 산소 결핍, 화재 등), 의료용(호기, 마취가스의 분석 등) 매우 광범위하며 점점 더 확대되어 가고 있다. 본 연구에서는 검출 가스 종류에 따라 졸-겔법으로 감응막을 최적 설계하고, 최적으로 설계된 감응막을 디핑법으로 코팅처리한 후 최적으로 열처리하여 센서를 제작하였다. 또한, 자체 제작한 가스검출 시스템에 제작된 센서를 장착하여 센서의 가스 검출 특성을 측정하고, 측정 데이터를 이용하여 휴대용 가스 검출 시스템을 설계 제작하였다.

• Korean Journal of Optics and Photonics
• /
• v.30 no.6
• /
• pp.226-229
• /
• 2019

We investigated an interrogation system for fiber Bragg gratings by using a 50-GHz 96-channel array waveguide grating. Linearity of the sensitivity (the wavelength shift in response to the change in strain or temperature) is achieved for a Bragg grating of sufficiently wide bandwidth. The present wavelength-monitoring system could measure the change in Bragg wavelength with a resolution of 0.01 nm, at intervals of 10 seconds. When this interrogation system was used for a linear array of 12 acrylaterecoated fiber gratings, the wavelength sensitivity changed from 0.018 nm/℃ to 0.01 nm/℃ when the operating temperature changed from -25℃ to 85℃.