• Journal of the Korea Society for Simulation
• /
• v.26 no.1
• /
• pp.47-54
• /
• 2017

This research explains a simulation method of cable crosstalk using Microwave Studio(MWS), Matlab and analyzes the crosstalk of Twisted Wire Pairs(TWP) applied to the aerospace or the military. TWP have a periodic configuration of long twisted wires along a axis. It is impossible to conduct the simulation of TWP due to the increased meshs according to the long length configuration. Transmission matrix(T-matrix) cascading method which is suitable to analyze the periodic configuration has been adopted to get the crosstalk of total cable so that the total simulation time has been decreased. In this paper, the crosstalk analysis of TWP including the connector modeled to straight sections has been performed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.12
• /
• pp.1115-1121
• /
• 2012

In this paper, the design of UTP LAN cable with enhanced alien crosstalk characteristic is proposed. Proposed LAN cable is made with jacket of the irregularly corrugation type. If necessary, it is possible to use the special cross-filler. The alien crosstalk characteristic is enhanced by using proposed cable with inner jacket of the irregularly corrugation type in wide frequency band. The design of the cable was based on parameters of the standard EIA/TIA 568-B.2-10.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.1
• /
• pp.85-93
• /
• 1988

Installation of the digital carrier system is increased rapidly in the telecommunication network, and most of systems are operating over a twisted pair conductor. Many systems are accommodated in multipair cable for their economical installation, therefore we must consider tha crosstalk interference between digital systesm. This paper considers the calculation method which determine crosstali interference between signals in multipair. And the transmission margin at a certain error rate is analyzed considering crosstalk power. Finally, this paper estimates the crosstalk noise susceptibility of 2.048Mbps relative to 1.544Mbps PCM system and 1.544Mbps relative to 2.048Mbps PCM system, and then considers the methos which both systems can operate together in a same cable.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.998-1004
• /
• 2004

In this paper we propose a discrete bit-loading algorithm that maximizes the transmit bit rate using the channel information. to optimize the performance of the very high-speed digital subscriber line(VDSL) system under the constraint of a maximum transmit power for each user. When the power level of crosstalk is high, the power allocation of a user changes the crosstalk experienced by the other users in the same binder. In this case, the performance of DSL modems can be improved by jointly considering the bit and power allocation of all users Simulation results shows that the proposed method improves the performance compared With that of iterative water-filling method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.1-10
• /
• 1999

In this paper, a method of canceling and suppressing differential-mode crosstalk-noise signals caused by non-uniform coupling between two transmission lines in UTP(Unshielded Twisted Paris) modular jacks is discussed. Differential-mode crosstalk-noise signals in balanced transmission lines in UTP modular jacks were suppressed by inserting auxiliary capacitance between balanced transmission line pairs which are located closely enough to be effectively coupled each other. To verify the effectiveness of the inserted capacitances, precisely calculated auxiliary capacitances were applied to 10 pin modular jacks which are used in local area networks at 100 Mb/s with unshielded twisted pair-cables. The NEXT(Near-End Crosstalk) losses were measured to prove its applicability.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.169-175
• /
• 2007

In High-Speed DSP systems, crosstalk between transmission lines of multi-channel can degrade the performance of equipment operations. This paper presents a microwave board to measure multi-channel coaxial cable assembly. The designed board has good performances from DC to 3 GHz, which have improved characteristic impedance, reduced crosstalk by using via fence, and low transmission loss. Using the designed board, we can measure characteristics of DUT(Device Under Test) such as return loss, insertion loss, crosstalk phase delay, and characteristic impedance. The measured results are used to improve performances of a produced coaxial cable assembly.

• Journal of Advanced Navigation Technology
• /
• v.22 no.2
• /
• pp.105-110
• /
• 2018

The North Korea nuclear issue is now posing a serious security threat to the Korea and Northeast Asia. Accordingly, the South Korean military is pushing for the introduction of long-range air-to-surface flights and the development of domestic nuclear facilities that can precisely hit North Korea headquarters building and nuclear facility even hundreds of kilometers above the border. In this paper, we removed the cable braid for securing the weight of the missile among several design elements for long-range air-to-surface missile development and estimated and analyzed the resulting performance. The possibility of braid removal was analyzed in terms of crosstalk inside the cable and CS114, RE101 of MIL-STD-461F.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.12
• /
• pp.33-42
• /
• 2007

The assessment of shear wave velocity($V_s$) in soft soils is extremely difficult due to the soil disturbances during sampling and field access. After a ring type field $V_s$ probe(FVP) has been developed, it has been applied at the southern coastal area of the Korean peninsular. This study presents the upgraded FVP "blade type FVP", which minimizes soil disturbance during penetration. Design concerns of the blade type FVP include the tip shape, soil disturbance, transducers, protection of the cables, and the electromagnetic coupling between transducers and cables. The cross-talking between cables is removed by grouping and extra grounding of the cables. The shear wave velocity of the FVP is simply calculated by using the travel distance and the first arrival time. The large calibration chamber tests are carried out to investigate the disturbance effect due to the penetration of FVP blade and the validity of the shear waves measured by the FVP. The blade type FVP is tested in soils up to 30m in depth. The shear wave velocity is measured every 10cm. This study suggests that the upgraded blade type FVP may be an effective device for measuring the shear wave velocity with minimized soil disturbance in the field.

• Journal of Advanced Navigation Technology
• /
• v.24 no.4
• /
• pp.245-250
• /
• 2020

Currently, unmanned military vehicles under development in Korea have more devices to carry out various missions, and interface cables between them are also increasing. In addition, due to a small space problem inside the unmanned vehicle, devices are required to be miniaturized and integrated. For two reasons, connectors also need to be selected, which makes them vulnerable to noise due to the closer distance between the pins. In this paper, we analyzed how much the magnetic field produced by noise at the connector pin where cable twist is released affects the surrounding pin and presented the guide for optimal pin placement. First, the effect of magnetic field is greater than the crosstalk between pin and pin. Second, the magnetic field on both sides between + and - is strong when approaching one step with noise source. Third, the magnetic field strength is improved when setting the ground pin as the ground pin between the noise and the original signal when approaching the A noise source and the two steps. Fourth, in the case of a differential mode communication, the optimal placement area of the sensitive signal was presented according to positions Tx± and Rx±.