• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.120-125
• /
• 2020

75 tonf liquid rocket engine combustion test was performed at Naro space center Engine Combustion Test Facility for KSLV-II. A gradual pressure drop was observed during off-design combustion test turbopump inlet condition using cooled kerosene at 271 K. It was found that the water content inside kerosene could cause pressure drop at 40 ㎛ grade filter through the water contests analysis of kerosene, kerosene cooling test and dehydration of kerosene.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.181-189
• /
• 2007

The technical requirements to the propellant of rocket engine using chemical energy are developed from the point of its performance, design and the exploration. The propellant, i.e. to get higher energy, to increase the cooling effect, and to be used in safety and comfort should be made. So from these aspect the technical requirements were written by the factors of physical chemistry. And the propellant combination used recently in Launch vehicles is liquid Oxygen and Kerosene, the main characteristics of this Kerosene as a fuel were reviewed. The toxicity and the safety of Kerosene, in specially, require the attention of the users. Also, it would be used in the development of Korean Kerosene by the comparative review of the several Kerosenes in Abroad.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.46-52
• /
• 2019

This research was conducted to analyze the effects of temperature on coking characteristics of kerosene. The kerosene was heated to 600 K, 700 K, and 800 K, and the cooled samples were collected. The used copper tubes were replaced according to the temperature conditions. The liquid and copper specimens were analyzed by gas chromatography-mass spectrometry and scanning electron microscopy equipped with an energy dispersive x-ray spectrometer, respectively. The results of the analysis confirmed that a carbon deposit was formed from the coking of fuel on the inner surface of the copper specimen at a relatively high temperature (800 K) of the copper tube.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.119-122
• /
• 2009

The purpose of this study is to design of film-cooling ring for the small thrust rocket engine using green propellants(Hydrogen peroxide and kerosene). Cold flow test was carried out to measure the mass flow rate and atomizing characteristic. Required mass flow rate was obtained from thermal analysis of the engine, and measured flow rate 42.25g/s was in the range of permissible coolant flow rate. With the same mass flow rate, cooling ring with more hole and high velocity shows better spray pattern. The result of thermal analysis, cooling ring has enough cooling performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.5
• /
• pp.37-46
• /
• 2012

The calculation model for heat transfer analysis of rocket engine combustion chamber considering film-cooling has been established. Convective, radiative heat transfers and film-cooling effect in combustion chamber were evaluated using empirical equations especially for rocket engine combustors, and for heat transfer outward from chamber wall general convective and radiative equations were applied. Structural grid has been generated inside chamber wall for FVM calculations, and transient thermal analyses were carried out by time-marching techniques. LOx/kerosene rocket engine with chamber pressure of 50 bar has been analysed, and it is shown that, in that case, the film-cooling less than 4% remarkably contributes to reduce wall temperature, but the effect of the effect of film-cooling more than about 4% is not significantly increased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.203-207
• /
• 2005

An experimental study was carried out to investigate the effect of film cooling in the thrust chamber of liquid rocket using LOx and Kerosene as propellant. The heat fluxes were obtained from the measured wall temperature to the axial direction of thrust chamber for different type of coolant, the various O/F ratio, mass flow rate and the location of the film cooling injector. A thin wall combustion chamber and nozzle were used to obtain the heat flux.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.69-77
• /
• 2020

A quasi one-dimensional multi-phase reaction flow analysis code is developed for the performance analysis of liquid pintle thrusters. Unsteady flow field, droplet evaporation, finite reaction and film cooling models are composed as the major models of the performance analysis. The droplet vaporization takes account of Abramzon's vaporization model, and the combustion employs a flamelet model based on detail chemical reactions. Shine's model is applied for the film cooling calculation. To verify each model, the Sod shock tube, single droplet vaporization, kerosene droplets combustion, and film length are evaluated.

• Aerospace Engineering and Technology
• /
• v.13 no.2
• /
• pp.150-159
• /
• 2014

This study provides a brief introduction to application of the computational fluid dynamics to domestic development of combustion devices for liquid-propellant rocket engines. Multi-dimensional flow analysis can provide information on the flow uniformity and pressure loss inside the propellent manifold, from which the design selection can be performed during the conceptual design phase. Multi-disciplinary performance analysis of the thurst chamber can also provide key information on performance-related design issues such as fuel film cooling and thermal barrier coating conditions. Further efforts should be made to develop numerical models to resolve the mixing and combustion characteristics of LOX/kerosene near the injection face plate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.69-75
• /
• 2011

Firing tests have been carried out for a technology demonstration model of 75-tonf-class combustor which is to be used on the liquid rocket engine of a Korean space launch vehicle. Firing tests were done at 50% of the nominal flow rate because of incapability of the test facility and limit of the test bed strength. Through the low pressure firing tests of 75-tonf-class channel cooling thrust chamber, operability and stability at the ignition and combustion phases were confirmed. Additionally it was foreseen that the 75-tonf-class thrust chamber would satisfy the performance requirements.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.10
• /
• pp.1001-1009
• /
• 2012

In this study, the cooling characteristics of combustion gas were investigated by injecting liquid nitrogen ($LN_2$) into a liquid rocket combustion chamber, which uses liquid oxygen (Lox) and kerosene as propellants. $LN_2$ injectors and an extended chamber for mixing were installed at the end of the ordinary LRE combustion chamber, and a nozzle was installed after the chamber for mixing. First, an ignition test of the liquid rocket engine was conducted to verify the stable combustion process. Next, a hot firing test was performed step-by-step for safety. Finally, the test was performed for 20 s. The results showed that the combustion gas of the LRE could be successfully cooled by using $LN_2$.