• KSBB Journal
• /
• v.22 no.4
• /
• pp.213-217
• /
• 2007

It has been reported that hydrophobic additives generally decrease the release rate of protein drugs from drug delivery systems (DDS) and hydrophilic additives increase the release rate. In many cases, however, the addition of hydrophilic molecule is necessary for improving the stability of protein drugs. In the present work, the effects of hydrophilic additives on the release profiles, and micelle formation of protein drug formulations were investigated to develop a novel method for protein drug delivery. For model protein drug, bovine serum albumin (BSA) was employed and several hydrophilic additives were used in the release experiments. Hydrophilic additive D-sorbitol showed the lower release rates of BSA than other hydrophobic additives due to the gel strengthening ability of the additive and the optimum concentration of D-sorbitol was 3 w/v % for the retarded release rate. In addition, it was found that the addition of D-sorbitol was very effective for obtaining homogeneous and stable DDS. The results were discussed in terms of the micelle formation and the micelle structure, i.e., the differences in gel structure and the distribution of drugs in micelles.

• Membrane Journal
• /
• v.11 no.4
• /
• pp.170-178
• /
• 2001

PVC microfiltration membrane was prepared by phase immersion method and applied to membrane bioreactor (MBR) contained activated sludge. The hydrophilicity of membrane and the pore size increase with the amount of additive(PVP) ducting the preparation of membrane. Permeation characteristics and the membrane fouling behavior were investigated by varying the internal environment in MBR using the prepared membranes. When there is a sludge bulking in MBR caused by microorganism, membrane fouling was accumulated. The cake layer resistance, R$_{c}$, of membrane increased in the order of CP-0 > CP-1.0 > CP-1.5. Rc increased up to 3.5~7 fold where the sludge bulking occurred in MBR. CP-1.5 seems to be appropriated membrane on the basis of the surface characteristics and the flux. The average flux of all the test membrane was 12(${\pm}$2) L/$m^2$hr whereas the COD removal efficiency was 98.8%. The ratio of bulking sludge and the type and the size of microorganism in operating MBR accelerate the membrane fouling and flux decline. It is concluded that the characteristic of membrane filtration depends on the hydrophilicity of membrane, the internal environment of MBR reactor and the growth factor of sludge.

• Journal of Adhesion and Interface
• /
• v.19 no.4
• /
• pp.145-153
• /
• 2018

In this study, adhesion promoters with acrylate and carboxylic acid moiety were synthesized from malenized polybutadiene and 2-hydroxyethyl acrylate for producing adhesive film with low water absorption and high adhesion. The surface properties, adhesion strength, mechanical properties and water absorption of adhesive films were characterized according to the amount of acrylate and carboxylic acid in the synthesized adhesion promoters. As the carboxylic acid in the adhesion promoters increased, the adhesion strength showed a tendency to increase and the mechanical properties also improved compared to the commercial adhesion promoter. The compatibility of adhesion promoters improved remarkably due to the presence of polybutadiene (hydrophobic nature), maleic anhydride (hydrophilic nature) and carboxylic acid (hydrophilic nature).

• KSBB Journal
• /
• v.18 no.5
• /
• pp.412-417
• /
• 2003

We first investigated basic characteristics of reticulated polyurethane (PU) foams as microbial carriers. In general, the specific surface area of PU foams increases with respect to decreasing pore sizes. However, the number of microbes adhered on the unit surface of reticulated PU foams decreases with respect to decreasing pore sizes. Thus, as a result of totally considering all effects such as apparent density, hydrolysis rate, and adhesion, we can know that PU foams with 45 PPI is the most appropriate microbial carrier. In this study, we can also investigate the effect of various physico-chemical surface treatments on the adhesion of microbes on the surface of PU foams. We used a chitosan treatment, a PEI (Polyethylene Imine) treatment, a xanthane treatment and a plasma treatment. As a result of comparing all surface treatments, the plasma surface treatment was the best.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.135.1-135.1
• /
• 2010

최근 고온에서 사용 가능한 PEMFC용 고분자전해질 막 개발에 대한 연구가 활발히 진행되고 있다. PEMFC가 고온에서 작동하게 되면 높은 성능과 많은 장점을 갖게 된다. PEMFC를 $100^{\circ}C$ 이상에서 운전하게 될 경우 백금 전극 반응을 향상시켜 고가의 백금 촉매 양을 줄일 수 있게 되고, 수소연료 속에 미량 포함된 CO에 의한 촉매표면 피독현상에 대한 내구성을 높일 수 있어 저 순도 수소연료 사용이 가능해 진다. 또한 가습장치와 수소 연료 개질장치의 부피를 줄일 수 있게 되어 전체적인 PEMFC 시스템이 단순화 된다. 현재 연료전지용 고분자 전해질막으로 DuPont사의 과-불소계 고분자 전해질막인 Nafion$^{(R)}$이 가장 널리 사용되고 있다. Nafion$^{(R)}$은 유연한 분자구조 안에 소수성이 강한 주사슬과 친수성을 나타내는 술폰산이 결합된 곁사슬이 존재하여 술폰화 곁사슬의 클러스터 둘레에는 친수성 영역이 형성이 되기때문에 소수/친수 상 분리가 잘되어 이온 클러스터 형성이 용이하지만 제조비용이 높은 단점을 갖고 있다. 특히, 전해질 막내에서 Bronsted base 역할을 하는 물에 의해 이온전도가 이루어지기 때문에 고온에서는 수분증발로 인해 성능이 급격히 감소된다. 따라서, 본 연구에서는 고온 저가습 조건에서 운전이 가능하고 Nafion이 갖는 문제점을 해결하고자, 내열특성이 뛰어나며 높은 수소이온 전도도 학보가 용이한 Sulfonated Poly(aryl ether)sulfone(SPAES) 고분자 전해질에, 고온에서도 수화성이 유지될 수 있도록 지르코니아를 황산화한 sulfated zirconia(s-$ZrO_2$)를 함침하여 복합 고분자전해질막을 제조하여 고온 저가습 조건에서의 수소이온 전도 특성에 관한 연구를 수행하였다. 개발된 막의 물리/화학적 특성은 water content(Wup%), 이온교환 용량(IEC, meq $g^{-1}$), 수소이온전도도(s $cm^{-1}$) 열 중량 분석(TGA), X선 회절분석(XRD) 등을 통하여 분석 및 관찰하였다. 내화학 및 열적 특성분석 결과, 황산화 반응공정으로 $ZrO_2$에 술폰산기가 안정적으로 결합하고 있음이 관찰되었으며, 본 연구에서 개발된 유 무기 복합막이 $250^{\circ}C$이상 열적안정성을 확보하고 있는 것으로 판단되었다. $100^{\circ}C$ 이하의 저온 영역에서, 일정 비율의 s-$ZrO_2$/SPAES막에서 이온교환용량(IEC)이 순수 SPAES 막보다 낮음에도 불구하고, water uptake가 증가함과 동시에 수소이온 전도도가 향상된 것을 관찰하였다. 또한, 고온에서는 수소이온이 자유롭게 이동할 수 있는 water channel을 형성하는 free water는 증발 하지만 s-$ZrO_2$와 SPAES의 술폰산기 사이에 강력하게 결합하고 있는 bound Water는 $100^{\circ}C$ 이상의 고온 영역에서도 존재하여, 비록 무가습 조건에서도 일정 비율의 s-$ZrO_2$/SPAES50 전해질 막의 경우, 높은 전도도를 나타냄을 관찰할 수 있었다. 따라서 본 연구를 통해 저가습 고온 적용을 목적으로 개발된 s-$ZrO_2$/SPAES50막은 우수한 내열 특성을 나타냄과 동시에 저가습 고온 영역($120^{\circ}C$, $50RH{\downarrow}$)에서 높은 수소이온 전도도를 유지하여, 고온 저가습 연료전지 운전에 적합할 것으로 사료된다.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.1
• /
• pp.31-36
• /
• 2008

This work was performed to evaluate the effect of membrane material and structure on fouling in a submerged membrane bioreactor(MBR). Three types of microfiltration membranes with the same pore size of 0.1 $\mu$m but different materials, polytetrafluoroethylene (PTFE), polycarbonate(PCTE) and polyester(PETE), were used. While PETE membrane exhibited the most rapid flux decline throughout the operation, PCTE and PTFE had a similar tendency with regard to permeability. Difference in permeability between PETE and the other membranes gradually decreased with time, which was probably due to chemical cleaning. The higher TOC rejection of PETE membrane could be attributable to its faster fouling, resulting from a larger amount of foulants to get attached to the membrane in a shorter time. DOC fractionation using a DAX-8 resin showed that the composition of each fraction between the supernatant and permeates did not change significantly with operation time, indicating that membrane hydrophilicity/hydrophobicity was not a dominant factor affecting to MBR fouling in this study. Compared to other membranes, the fouling of PETE membrane was more influenced by pore clogging (irreversible fouling), which would probably contribute to a higher organic rejection of the PETE membrane.

• Clean Technology
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2002

In the present study the membrane filtration characteristics of a commercially available synthetic water-based cutting oil through two kinds of ultrafiltration membranes (HF1-45-CM50 and HF1-43-CM100) with molecular weight cut-offs of 50,000 and 100,000, respectively, have been investigated in detail. Among these membranes, the hydrophilic one (HF1-45-CM50) was found to show a satisfactory result for both the permeate flux and the permeability of oil components, whereas the permeate flux obtained with the hydrophobic membrane (HF1-43-CM100) appears to be significantly low, indicating that synthetic cutting oil was easily wetted on the hydrophobic membrane surface and induced more membrane fouling. The effect of material characteristics of the membrane on the filtration characteristics was found to be much more significant compared with the mean pore size of the membrane. Backflushing by nitrogen gas was applied to reduce the formation of a gel layer and membrane fouling. With the hydrophilic membrane, the backflushing was found to increase the permeate flux, whereas the backflushing resulted in a decrease in flux for the hydrophobic membrane. The flux recovery was observed to be highest when the membranes fouled with waste synthetic cutting oil were immersed into a cleaning solution for more than 72 hours and then backflushed by nitrogen gas.

• The Korean Journal of Pesticide Science
• /
• v.12 no.2
• /
• pp.127-133
• /
• 2008

The foliar uptake of dimethomorph into cucumber was assessed by spray application of aqueous dimethomorph solution containing fatty alcohol ethoxylate (FAE) or fatty acid alkyl ester as activator adjuvants. Afterward, the possible mechanism of action of FAE on foliar penetration of active ingredient was suggested by speculating on the effect of lipophile and hydrophile of FAEs. The amount of absorbed dimethomorph induced by polyoxyethylene mono-9-octadecenyl ether (6 moles ethylene oxide, $C_{18=9}E_6$) was linearly related to the concentrations of surfactant as well as dimethomorph in spray solution, suggesting that it is simply a diffusion phenomenon of the solute molecule through a cuticular membrane from leaf surface. Octadecanol attached to FAE was most effective lipophile on the leaf penetration of dimethomorph. And, the more ethylene oxide had the polyoxyethylene chain of FAE up to 20 moles, the higher the uptake rate was. Therefore, the role of lipophile of FAE on dimethomorph penetration to cucumber leaf, probably, is to modify the physico-chemical properties of cuticular membrane to be permeable to dimethomorph, and the polyoxyethylene chain having less than 20 moles ethylene oxide, which is moderately permeable to cuticular membrane by its molar volume, is to let the physically-modified cuticular membrane to be maintained for a longtime.

• Journal of Sensor Science and Technology
• /
• v.3 no.2
• /
• pp.74-80
• /
• 1994

Silicon direct bonding technology is very attractive for both silicon-on-insulator devices and sensor fabrication because of its thermal stress free structure and stability. The process of SDB includes hydration of silicon wafer and heat treatment in a wet oxidation furnace. After hydration process, hydroxyl groups of silicon wafer were analyzed by using Fourier transformation-infrared spectroscopy. In case of hydrophilic treatment using a ($H_{2}O_{2}\;:\;H_{2}SO_{4}$) solution, hydroxyl groups are observed in a broad band around the 3474 $cm^{-1}$ region. However, hydroxyl groups do not appear in case of diluted HF solution. The bonded wafer was etched by using tetramethylammonium hydroxide etchant. The surface of the self etch-stopped silicon dioxide is completely flat, so that it can be used as sensor applications such as pressure, flow and acceleration, etc..

• Membrane Journal
• /
• v.17 no.1
• /
• pp.44-53
• /
• 2007

The primary objective of this study is to increase the extent of water flux and fouling resistance of nano-filtration or reverse osmosis membranes. This study was performed to investigate the effect of surface characteristics of silane coated membranes on modified fouling index. Commercial polyamide composite RO membrane (RE1812-LP) and NF membrane (ESNA4040-LF) were treated with silane coupling agents in ethanol at five different concentrations. The silane coupling reagent, aminopropylmethoxydiethoxysilane, contains one aminoalkyl and three alkoxy groups. The hydrophilic effect of aminoalkyl group of APMDES on the permeability and fouling resistance of the modified membrane was examined. The surfaces of the modified membranes were characterized by FE-SEM, contact angle analyzer, and zeta potentiometer in order to confirm successful sol-gel methods. The modified NF membranes showed significantly enhanced water flux and fouling resistance without a decrease in salt rejection in divalent ionic feed solution.