• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.104-110
• /
• 1997

To predict the effect of ring expansion and ring compression on residual stress relief of Al 7175 ring rot]s, 2-D axisymmetric thermal analysis and elastoplastic analysis were performed. The residual stress distributions along the thickness of T73, T7351 and T7352 treated rings were measured using three step sectioning method. The measured results were compared to numerical ones for quenched and stress relieved rings. After quenching, calculated hoop and axial residual stresses were similar to measured ones for T73 treated rings. The residual stresses of T7351 and T7352 treated rings were decreased remarkably compared to T73 treated rings. The effect of axial residual stress relief was superior to that of hoop one, and also ring compression to ring expansion. It was concluded that ring compression is advantageous over ring expansion in view of stress relief effect and practicality, and vice versa in view of dimensional control and press power.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.82-82
• /
• 2017

현대농업에서 잡초를 조기에 제거하지 못할 경우 작물의 성장에 장애를 초래하므로 제초작업은 매우 중요하다. 최근 친환경 고품질 농산물에 대한 소비자의 관심과 고품질 농산물에 대한 가격 차별화 등으로 제초제를 사용하지 않은 친환경 재배가 주목을 받고 있다. 제초제는 농작물에 따라 분류가 되어있어 종류마다 효과가 다르고 사용방법이 종류에 따라 어떻게 사용되는지 알기가 쉽지 않아 이에 따른 피해 또한 무시 할 수 없다. 현재 상용화되어 있는 제초기는 굴곡이 있는 고랑의 잡초를 효율적으로 제거하기 어려워 밭작물 제초작업에 사용하기 부적합하다. 밭작물 재배 기간에 행해지는 고랑의 제초작업은 평지보다 더 많은 힘이 필요하고 일반적인 제초기로는 좋은 결과를 얻기 어렵다. 또한 제초 작업시 농작물 피해와 멀칭 비닐을 손상시키는 문제가 발생 하고 있다. 따라서 밭작물에 효율적인 잡초를 제거하기 위해 굴곡이 있는 지형의 잡초를 제거하기 위한 제초기 개발이 반드시 필요하다. 밭작물용 제초기를 개발하기 위해 굴곡이 있는 고랑의 잡초 제거가 가능한 제초날의 형상 설계가 우선되어야 하며, 고랑의 잡초제거를 위한 제초날 형상설계를 하기 위해 우리나라 주요 밭작물 재배지의 이랑 넓이, 고랑 깊이 및 고랑 폭을 조사 분석하였다. 조사 작물 대상은 양파, 마늘, 무, 배추, 고추, 당근, 감자 총 7가지 작물을 대상으로 조사하였으며, 각 작물들의 이랑 넓이와 고랑 깊이 및 폭의 평균치를 구하여 제초날 설계에 적용하고자 하였다. 범위가 있는 수치는 높은 수치를 기준으로 계산하였으며 고랑의 평균 폭은 34.2cm이고, 고랑의 평균 깊이는 22.1cm가 나타났다. 잡초를 효과적으로 제거하기 위해 제초날의 형상은 고랑의 크기 및 형태에 맞게 원형으로 설계를 하여야 한다. 형상 설계는 밭작물 고랑 평균직경 및 평균높이를 고려하고, 제초작업시 제초날이 작물 및 멀칭비닐의 손상 하지 않도록 하기 위해 직경은 고랑 평균 폭의 75% 정도 치수로 형상을 설계하고, 제초날 깊이는 고랑의 굴곡형태을 고려할 때 제초날 반경의 70%정도로 설계하여 원형제초날 폭 250mm, 제초날 깊이 87.5mm로 설계해야 할 것으로 분석 되었다.

• The korean journal of orthodontics
• /
• v.34 no.1 s.102
• /
• pp.83-91
• /
• 2004

This study was performed to examine treatment efficiency and patient discomfort rate according to used handpiece speed in clean-up technique. Brackets were bonded to extracted human premolar(50 teeth). After debonding, 50 extracted human premolar were divided Into each two groups(low speed handpiece group with tungsten carbide bur and high speed handpiece group with ultra-fine diamond finishing bur) of 25 according to used handpiece speed in clean-up technique. In clean-up procedure, teeth vibration and pulp thermal changes were measured. After clean-up procedure, the enamel surfaces of randomly selected 10 teeth from each two groups were taken by SEM and evaluated. The findings of this study were as follows ; 1. During resin removal, tooth vibrations of various amplitude in low speed handpiece group were more than those of high speed handpiece. 2. The pulpal thermal changes of high speed handpiece group were significantly higher than those of low speed handpiece group, also the resin removal time in high speed handpiece group was almost as twice as in low speed handpiece group. 3. The figures of SEM to enamel surfaces after resin removal showed that notches and resin remnants in high speed handpiece group were more than those in low speed handpiece group.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.277-286
• /
• 2001

Among the ULSAB methods for the lightweight automobile body, Tailor Welded Blank(TWB) is adopted and the design process is developed for the existing component. Topology optimization conducted to find the distribution of the variable thickness. The number of parts and the welding lines are determined from it. In the detail design, size optimization is carried out to find the optimum thickness of each part and then, the final parting lines are tuned by shape optimization. A commercial optimization software GENESIS is utilized for the optimization processes.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.544-544
• /
• 2016

최근 지구온난화 등 기후변화에 따른 돌발 홍수가 계절과 관계없이 빈번하게 발생하고 있으며, 국지성 호우 및 태풍의 영향으로 인한 홍수피해가 매년 발생하고 있다. 이와 같은 피해를 저감하기 위해서는 정확한 강우 관측 및 홍수량 산정이 매우 중요하기 때문에 많은 수문학적 연구와 기술 발달이 이루어지고 있다. 그 중 강우의 변화를 실시간으로 관측 가능한 레이더영상 자료의 활용성이 증대되어 활발한 연구가 진행되고 있으나, 제주도의 경우 다른 지역에 비해 연구가 미흡한 실정이다. 이에 따라, 제주도 유역을 대상으로 유역의 공간적 특성을 격자기반으로 분석하고 매개변수 산정 시 경험적 요인을 제거할 수 있는 분포형 모형인 Vflo와 기상청에서 제공하는 레이더 영상자료 및 강우자료를 활용하여 연구를 수행하였다. 본 연구에서는 Arc-GIS를 이용하여 제주도 도심하천인 외도천 유역의 지형적 지리적 특성(DEM, 토양도, 토지피복도 등)을 $30m{\times}30m$ 격자크기로 분석하고, 레이더영상 자료로부터 강우 자료를 추출하였으며, 분포형 모형(Vflo)을 활용하여 유출량을 모의하였다. FSIV기법을 통해 현장 관측한 유출량과 비교 분석하였으며, 레이더 영상자료로부터 추출한 강우자료는 AWS자료를 활용하여 제주도에 적합한 강우보정계수를 산정하였다. 이와 같은 연구를 통해 향후 제주도 미계측 유역의 홍수량 산정이 가능할 것으로 판단되며, 하천기본계획 및 유역종합치수계획 등 치수계획 수립 시 많은 활용이 될 것으로 기대한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.721-727
• /
• 2015

The mechanical components for wind turbines are mainly manufactured using open-die forging. This research introduces an advanced forging method to produce the door frame of the tubular wind turbine tower. The advantages of this new forging method are an increase in the raw material utilization ratio and a reduction in energy cost. In the conventional method, the door frame is hot forged with a hydraulic press and amounts of material are machined out because of the shape difference between the forged and final machine products. The proposed forging method is composed of hot forging and ring rolling processes to increase the material utilization ratio. The effectiveness of this new forging method is deeply related to the ring rolled blank dimension before the final forging. To get the optimal ring rolled blank, forged shape prediction using the finite element analysis method was applied. The forged dimensions produced by the new forging method were verified through the first article production.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.41 no.2
• /
• pp.174-179
• /
• 2014

Dens invaginatus is a developmental anomaly resulting from an infolding of the enamel organ into the dental papilla prior to calcification of the dental tissue. Clinical and radiographic presentation of dens invaginatus shows a lot of variation. The classification proposed by Oehlers(1957) is most commonly used among classifications of dens invaginatus. Several treatments have been suggested to treat Type III dens invaginatus where the pulp remains healthy but the invagination is associated with a periodontitis. The top priority objective is to preserve pulp as sound as possible. Thus, if there is no definite evidence of pulpal disease, the conservative access which treat invagination as distinct from the pulp is necessary. But, Endodontic treatment of Type III dens invaginatus has the particular problems associated with achieving adequate chemomechanical debridement of the root canal system and invagination, predictable length control and consistent filling. In this case report, the endodontic treatment limited within invagination was performed for treatment of Type III dens invaginatus, and filling with Mineral Trioxide Aggregate(MTA) resulted in good prognosis.

• Journal of Korean Society of Forest Science
• /
• v.107 no.1
• /
• pp.25-34
• /
• 2018

This study was performed to discover the comparison of the understory species composition and the growth velocity of the regeneration seedlings in Pinus densiflora forests being managed by the seed-tree method from 2008 year. The investigation site located in Bonghwa, Gyeongsangbuk-do province was established by eighteen quadrats such as six control ones, six slope ones and 6 concave ones, in which we carried out the vegetation survey and measured annual height growth of each seedlings. As a result of vegetation analysis, the understory vegetation of the seed-tree forest area was mainly composed of shrub plants such as Lespedeza bicolor, Zanthoxylum schinifolium, Securinega suffruticosa, Lespedeza maximowiczii and Stephanandra incisa, herb plants such as Miscanthus sinensis var. purpurascens, Carex humilis var. nana, Spodiopogon sibiricus and Artemisia keiskeana, and vine plants such as Pueraria lobata, Smilax sieboldii, Dioscorea batatas, Actinidia arguta, Vitis amurensis and Rubus crataegifolius. Especially, the vine plants were relatively more imported to the concave site than the control site and the slope site. As a result of measurement of growth velocity, the seedlings of the Pinus densiflora appeared to be 3,175 trees/ha for the non-suppressed trees and 7,842 trees/ha for the suppressed trees. In cases of the concave site, individuals of seedlings were much lower than those on the slope site, probably due to the competition effects of vine plants. Consideringly, silvicultural practices for clearing the vine plants should be inevitably accompanied. Also, the growth velocity of the suppressed and non-suppressed trees has been constantly increasing, those of the non-suppressed trees much higher than the suppressed trees. This represents that the seedlings grow rapidly after the suppressed period with competition to the surrounding plants. Therefore, specific practices such as blush control and vine clear should be carried out at the beginning stage of regeneration in the seed-tree stand.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.38 no.1
• /
• pp.44-50
• /
• 2011

An immature tooth with infected pulp has numerous potential complications. Conventional apexification with calcium hydroxide has several disadvantages, including susceptibility to tooth fracture. This method does not promote continual root development. Pulp revascularization of a necrotic, immature permanent tooth will allow further development of the root and dentinal structure. Disinfection of the root canal system is a prerequisite for pulp revascularization and tissue regeneration. A combination of antibiotic drugs (ciprofloxacin, metronidazole, and minocycline) is effective for disinfection of necrotic pulp, and has been used successfully in regenerative endodontic treatment. These case reports involve the treatment of 3 immature permanent teeth with necrotic pulp using a 3-Mix paste and mineral trioxide aggregate. All cases showed the notable apical maturation with closure of the apex and increased thickness of dentinal walls. This approach suggests a paradigm shift in treating endodontically involved immature permanent teeth from the traditional apexification with calcium hydroxide to the conservative approach by providing a favorable environment for tissue regeneration.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.4
• /
• pp.558-563
• /
• 2000

The lasers have been used in dentistry for more than 30 years and the application of lasers for drilling dental hard tissue has been investigated since the early developement of lasers. Recently, the Er:YAG laser was invented for hard tissue ablation. The Er:YAG laser, having a wavelength of 2.94um, is highly absorbed in both water and hydroxiapatite, leading to a very effective material for hard tissue removal by bursting off the solid tissue component that is, enamel and dentin are removed by the Er :YAG laser by water vaporization and microexplosion, without any melting of inorganic tissues. Therefore, the Er:YAG laser produced round craters with well defined margins and the surrounding tissues had no cracks and no charring. When used for cavity preparation, pulpal damage should not occur if hear buildup is minimized by careful selection of exposure parameters and by use of a water spray. The present study demonstrated that the Er:YAG laser cut the tooth substance adequately for composite resin restoration, without having undesirable side effects such as harmful effects on the pulp, discoloration or cracking etc. Also, the child patients were well cooperative during laser treatment mainly because of little noise, lesser vibration and minimal pain compared to conventional means of cavity preparation.