• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.67-77
• /
• 1998

Homogeneous liquids of Ni-21.5Nb-2.5Al and Ni-23.3Nb eutectic superalloys were solidified into Ni/$Ni_3$Al-$Ni_3$Nb(${\gamma}$/${\gamma}$'-${\delta}$)and Ni-Ni/$Ni_3$Nb(${\gamma}$-${\delta}$) phase by directional solidification and the effect of interlamellar spacing on microsturctural stability at high temperatures, hardness variation with growth rate was studied. The interlamellar spacing(${\lambda}$) in the eutectics was varied with the growth rate(R), corresponding to "${\lambda}^2$R ＝Constant" relationship. Isothermal heat treatments of the eutectics used in this study, provided the microstructural stability improvement at hight temperature as the interlamellar spacing increases. It was also seen that the hardness improvement is made with the growth raterowth rate

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.2
• /
• pp.1-8
• /
• 1991

The spheroidization of cold rolled lamellar pearlite in annealing at the temperatures between 600 and $700^{\circ}C$ has been studied by quantitative micrography. It was foud that the spheroidization proceeded as two stageh. The first stage was the stage of relieving the stored energy by cold work, the second was the stage of reducing the interface energy between ferrite and cementite. The spheroidization rate combining the spheroidization rate of each stages is described by the following equation : $$d(1/S)/dt=k_3{\cdot}D/_{(1/s)}\{{\sigma}V/_{(1/s)}+k_4{\cdot}{\exp}(-bt)\}$$ Where, S is the total area of the interface between ferrite and cementite per unit volume, D is the diffusion coefficient, ${\sigma}$ is the boundary energy, V is the volume fraction of the cementite, and $k_3$, $k_4$, b are constants.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.127-137
• /
• 1993

The changes of lamellar(${\alpha}_2+{\gamma}$) structure of TiAl intermetallic compound which is a high potential, high temperature aerospace material was investigated by heat treatment. The lamellar structure was short and made subgrain in prior a grains after homogenizing at 1523 K. It became longer and finer, and the subgrain went out during subsequent isothermal heatteating at 1273 K. The yield, fracture strength and strain to fracture if the heat treated specimens was increased and the hardness of them was decreased a little in the finer lamellar structure, because fine lamellar interface, sugrain boundary and grain boundary may block initiation and propagation of crack.

• Composites Research
• /
• v.13 no.6
• /
• pp.23-29
• /
• 2000

The internal residual stresses within the multilayered structure with sharp interface induced by the difference in thermal expansion coefficient between the materials of adjacent layers often provide the source of failure such as delamination of interfaces etc. Recent development of the multilayered structure with functionally graded interface would be the solution to prevent this kind of failure. However a systematic thermo-mechanical analysis is needed for the customized structural design of multilayered structure. In this study, theoretical model for the thermo-mechanical analysis is developed for multilayered structures of the $Al-SiC_p$ functionally graded composite for electronic packaging. The evolution of curvature and internal stresses in response to temperature variations is presented for the different combinations of geometry. The resultant analytical solutions are used for the optimal design of the multilayered structures with functionally graded interface as well as with sharp interface.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.629-635
• /
• 2000

The texture evolution during isothermal forging and subsequent heat treatment in Ti-48.5at%Al-0.6at%Mo alloy was investigated. Especially, in the present study, research interest was focused on the interrelation between lamellar volume fraction and textures varied with the change of heat-treated time and temperature. It was found that texture components having ND┴{302) and TD$\perp${100} with minor TD$\perp${111} were developed by isothermal forging. In addition, when the followed heat-treatment time and temperature increased from $1330^{\circ}C$/10h to $1350^{\circ}C$/20h respectively, both the lamellar volume fraction and the intensity of textures mentioned above also gradually increased. However, the tensile elongation at room temperature decreased oppositely, as the lamellar volume fraction increased. These results suggested that tensile properties of $\gamma$-TiAl with the nearly lamellar microstructure at room temperature were affected more strongly by the microstructural features such as lamellar volume fraction rather than by textures.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.4 s.19
• /
• pp.70-78
• /
• 2004

A study has been made to investigate the high temperature deformation behavior of Ti-6Al-4V alloyand to predict the final microstructure under given forming conditions. Equiaxed and $Widmanst\ddot{a}tten$ microstructures of Ti-6Al-4V alloys were prepared as initial microstructures. By performing the compression tests at high temperatures$(700\~1100^{\circ}C)$ and at a wide range of strain rates$(10^{-4}\~10^2/s)$, various parameters such as strain rate sensitivity(m) and activation energy(Q) were calculated and used to establish constitutive equations. When the specimens were deformed up to strain 0.6, equiaxed microstructure did not show any significant changes in microstructure, while $Widmanst\ddot{a}tten$ microstructure revealed considerable flow softening, which was attributed to the globularization of a platelet at the temperature range of $800\~970^{\circ}C$ and at the strain rate range of $10^{-4}\~10^{-2}/s$. To predict the final microstructure after forming, finite element analysis was performed considering the microstructural evolution during the deformation. The grain size and the volume fraction of second phase of deformed body were predicted and compared with the experimental results.

• Proceedings of the KOR-BRONCHOESO Conference
• /
• 1987.05a
• /
• pp.18.2-18
• /
• 1987

Plastic bronchitis는 길고, 분지된 기관지원주(bronchial cast)의 형성과 기관지원주의 현미경 검사상, 염증세포를 포함하고 있는 농후한 점액의 층상 구조를 특징으로 하는 질환으로, 과거에는 fibrinous bronchitis, pseudomembranous bronchitis 그리고 Hoffman's bronchitis로 불려졌으며, 소아와 성인에서 발생하는 드문 질환으로 알려져 있다. 본 교실에서는 갑작스러운 발열, 기침 및 호흡 곤란을 동반하고, 흉부 단순 X-선 검사상 좌측 흉부에 무기폐 소견을 보인 19개월 남아에서, 기관지경 검사를 시행하여 제거한 조직의 육안 및 광학현미경 검사상 plastic bronchitis를 의심할 수 있는 1례를 경험하였기에 보고하는 바이다.

• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.4
• /
• pp.255-264
• /
• 2021

Asian dust (Hwangsa) deposited on the surface of the Korean Peninsula is difficult to recognize their existence in mountainous terrain undergoing active erosion and weathering. This study examined Asian dust sediments mixed in soils by analysing clay mineralogy, mineral composition, and microtextures of fine silt (< 20 ㎛) in the alkali feldspar granite area of Seoraksan. The fine silt was composed of detrital particles derived from bedrocks, Asian dust sediments, and their weathering products. Clay minerals of 2:1 structural type, chlorite, amphibole, epidote, and Ca-bearing plagioclase were identified as eolian mineral particles. During the weathering of the bedrock composed of quartz and alkali feldspars, albite was partially weathered to produce small amounts of gibbsite and kaolin minerals. Hydroxy-Al interlayered clay minerals were formed by the exchange and fixation of polynuclear Al cationic species into the interlayers of expandable 2:1 clay minerals dominated by illite-smectite series clay minerals. Contribution of Asian dust to the fine silt of soils was estimated around 70% on the basis of total contents of 2:1 phyllosilicates.

• Composites Research
• /
• v.12 no.5
• /
• pp.87-97
• /
• 1999

A clad material is a different type of the typical composites which are composed of two or more matericals joined at their interface surface. The advantge of cald material is that the combination of different materials can satisfy both the need of good mechanical properties and the other demand of user such as electrical properties instantaneously. This paper is concerned with the direct and indirect extrusion processes of copper-clad aluminum rod. Extrusion of copper-clad aluminum rod was simulated using a commercially available finite element package of DEFORM. The simulations were performed for copperclad aluminum rod to predict the distributions of temperature, effective stress, effective strain rate and mean stress for sheath thicknesses, die exit diameters and die temperatures.

• Journal of Korean Ophthalmic Optics Society
• /
• v.12 no.3
• /
• pp.55-58
• /
• 2007

Titanum and its alloys have been used as the important materials of eyewear frame due to its light weight, mechanical strength and corrosion resistance. This study investigates hardness and microstructures of titanum alloy groove wires in according with heating time by high frequency induction heating. Because of increase of grain size by the growth of heating time, hardness of ${\beta}-Ti$ has reduced. Hardness of Ti-325 reduced until 2 sec and rapidly increased at 3 sec by high frequency induction heating. It is observed that hardness of Ti-325 reduces by the increase of the grain size until 2 sec and suddenly increased by the development of the detailed ${\alpha}+{\beta}$ lamella at 3 sec.