• Journal of Korean Society of Disaster and Security
• /
• v.14 no.3
• /
• pp.51-63
• /
• 2021

This study is for the quality improvement of water-sealing & reinforcement grouting in tunnel of the construction of the underground transportation network underneath the city. Existing tunnel grouting process did not technically utilize P~q~t charts fully. It is due to the absence of technical methods to decide how P~q~t charts change in the presence of trouble and what the change represents in grouting. There were no standards to decide which chart pattern represents which ground characteristics, how to categorize ground types, and how to take measures according to the standards. This paper studies on the grouting type, ground characteristics, ground type categorizing method, and countermeasures for both general and algorithm-processed grouting in soil and rock layer to address the aforementioned problems. Newly improved P~q~t charts from grouting in soil was categorized into six different types. Different characteristics and categorization method was developed for each type. Countermeasures for each type of grouting process were developed so that on-site application can be readily available. Improved P~q~t charts for rock layer also have six different types of grouting. Each type was given the countermeasures for rock layer grouting process for easier applications. Therefore, it is expected to be used through out the entire process of grouting from preparation to the last report of the water-sealing & reinforcement grouting in tunnel of the construction of the underground transportation network underneath the city.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.11
• /
• pp.85-95
• /
• 2023

This study implemented intelligent compaction technology at the construction site of the AY Highway in Gyeonggi Province, with a focus on obtaining the representative intelligent compaction value, CMV. The target CMV for quality control was established through trial construction, and the validation of the compaction quality control process based on intelligent compaction was conducted. The optimal approach for determining the target CMV was confirmed to be through linear regression of the average CMV measured within a 5-m radius from the plate load testing location. Upon assessing compaction quality against the target CMV, it was observed that the quality criteria outlined in the domestic intelligent compaction standard were met. However, the criteria outlined in Austria and the United States were not satisfied. Notably, indicators related to the variability of compaction quality did not meet the specified criteria, suggesting a stringent standard compared to the observed variability of CMV, ranging from 17% to 55%. Consequently, it is recommended to conduct additional field tests to further validate the compaction quality control process based on intelligent compaction. This will aid in confirming and enhancing the appropriateness of the regulations stipulated in each standard.

• Journal of Music and Human Behavior
• /
• v.10 no.2
• /
• pp.1-33
• /
• 2013

The aim of this study was to systematically review the latest clinical trials in music medicine and medical music therapy for pediatric patients. Thirteen databases were searched to obtain randomized controlled/crossover design studies published between the year 2000 and 2012 in English language. Out of 1012 articles retrieved in the initial search, fifteen studies were identified based on an exclusion criteria. Overall, selected articles involved children 1 month to 18 years, sample size of 11 to 150, and total participants of 987. Studies were classified and compared as music medicine or music therapy studies through a systematic synthesis assessing general characteristics, methodological quality, measured outcomes, types of interventions and the study results. Seven music medicine and eight music therapy studies measured seven dependent variables using thirty-six different measurement tools with a large heterogeneity in the selection, type, and method of music interventions. Evaluation of the methodological quality revealed that many studies did not provide a full report of the research method, and did not meet some or most methodological standards, such as randomization, allocation concealment, double or partial blinding, and intention to treat analysis. Although overall research results were positive if not significant, poor methodological quality and heterogeneity in design and intervention strategies raise the question of research bias and trustworthiness issues. The systematic review concluded that music may have a valuable clinical effect in addressing the physical and psychosocial needs of hospitalized children, although more rigorous, homogeneous and replicable studies are greatly needed.

• Journal of Food Hygiene and Safety
• /
• v.15 no.2
• /
• pp.114-121
• /
• 2000

A study was carried out to establish a detection method for irradiated black and white pepper. Samples were packed in polyethylene bags and irradiated with 2.5, 5, 7.5, 10 and 15 kGy using a Co-60 irradiator. The samples were suspended in water, and alkalized with sodium hydroxide solution. Apparent viscosity was determined after heat gelatinization using a Brookfield DV-III rotation viscometer at 30。C with 30, 60, 90, 120, 150, 180, and 210 rpm. Means and standard deviations of the viscosities of all samples decreased by increasing the stirring speeds. The viscosities increased in all samples by increasing the concentration. Regression expressions and coefficients of viscosity which decreased with increasing irradiation dose of 10% and 13% black pepper, and 7% and 10% white pepper were 0.9531 (y=-131.29x+1,769.0), 0.9725 (y=-351.33x+4,036.0), 0.9731 (y=2,208.0e${^-0.3546X}$), and 0.9959 (y=5,116.0e${^-0.2887X}$), respectively, at 120 rpm. This trend was similar fur all stirring speeds. These results suggest that the detection of irradiated black and white pepper at various doses is possible by the viscometric method.

• Korean Journal of Clinical Laboratory Science
• /
• v.49 no.4
• /
• pp.382-389
• /
• 2017

Currently, reticulocyte experimental calculation technology used in clinical laboratories are divided two types: manual and automated. Manual reticulocyte counting using a microscopy lacks accuracy due particularly to its low reproducibility, affecting the accuracy of manual reticulocyte count. Moreover, Automatic blood corpuscle analyzer flow cytometry is difficult to be used in underdeveloped countries and small scale laboratories due to relatively high cost. Therefore, this study tried to find a new method to complement these drawbacks. The aim of this study was to compare the stained reticulocytes count by spectrophotometer and also to analyze the statistics of spectrophotometer and flow cytometer. The same 8 EDTA samples were repeated 36 times to compare the agreement between spectrophotometer and flow cytometer. This study measured the specimen diluted 600 times at 700~780 nm by 10 differences. Wavelength between 710 to 730 by absorbance showed a positive correlation between standard data and test data (r=0.967, p<0.01), presenting a correlation between variables. Statistical analyses of regression for test and standard parametric data, the optimal dilution factor was 600 times. Therefore, this study tried to technical utilizes such as contributing economical for the reticulocyte absorbance apply from the auto spectrophotometer, a monitoring system for the reticulocyte relation anemia, etc. Therefore, more extensive studies, including an auto chemical analyzer application, will be needed.

• Journal of Internet Computing and Services
• /
• v.23 no.3
• /
• pp.13-20
• /
• 2022

IEEE 802.11ay Wi-Fi is the next generation wireless technology and operates in mmWave band. It supports the MU-MIMO (Multiple User Multiple Input Multiple Output) transmission in which an AP (Access Point) can transmit multiple data streams simultaneously to multiple STAs (Stations). To this end, the AP should perform MU-MIMO beamforming training with the STAs. For efficient MU-MIMO beamforming training, it is important for the AP to estimate signal strength measured at each STA at which multiple beams are used simultaneously. Therefore, in the paper, we propose a deep learning-based link quality estimation scheme. Our proposed scheme estimates the signal strength with high accuracy by utilizing a deep learning model pre-trained for a certain indoor or outdoor propagation scenario. Specifically, to estimate the signal strength of the multiple concurrent beams, our scheme uses the signal strengths of the respective single beams, which can be obtained without additional signaling overhead, as the input of the deep learning model. For performance evaluation, we utilized a Q-D (Quasi-Deterministic) Channel Realization open source software and extensive channel measurement campaigns were conducted with NIST (National Institute of Standards and Technology) to implement the millimeter wave (mmWave) channel. Our simulation results demonstrate that our proposed scheme outperforms comparison schemes in terms of the accuracy of the signal strength estimation.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.86-86
• /
• 2017

마늘파종기는 파종기구동부와 파종후 파종홀의 복토역할을 하는 파종기롤러, 지면과의 마찰을 통해 바퀴의 회전토크가 발생하며 발생된 토크는 파종기 내부 동력으로 전달되어 전체 파종시스템(배종, 호퍼캠, 파종부)을 동작 시키는 기능을 수행하는 파종바퀴, 마늘종구를 한알씩 집어올려 중간이송컵으로 이송하는 자세교정컵이 포함된 배종부와 자세교정컵에서 낙하된 마늘종구를 땅속으로 파종하는 파종장치로 구성된다. 배종율 95%, 2립 배종률 5% 성능을 확보할 수 있는 기술이 개발될 경우 세계적으로도 독보적인 기술 우위를 확보할 수 있다. 이와 같은 기본적인 기능을 구현할 수 있는 컨셉모델에 대한 설계를 수행하여 시제품개발 전 기구해석과 구조해석 등을 위한 기본설계를 수행하였다. 배종율 95% 이상을 확보하기 위해서는 기존의 현장경험의 의한 설계 방식으로는 한계가 있기 때문에 시뮬레이션 및 분석 개발이 필요한데, 프레임은 고정밀 마늘종구 배종부 장착을 위한 기본 구조물로써 작동시 동력을 얻기 위한 바퀴와 연계가 되도록 설계되었으며, 호퍼는 배종 수행을 위해 마늘을 저장해 두는 통으로써 배종부와 연결된다. 배종부의 배종판이 회전함에 따라서 배종판의 홈이 호퍼 내로 들어갔다 나오면서 마늘을 집게되며, 동력 전달부는 배종판을 회전시켜주고, 회전 속도 조절을 가능하게 한다. 파종부는 배종부에서 중간컵을 통해 하나씩 공급해준 마늘을 땅에 심는 부분으로서. 프레임의 바퀴 회전과 연동되어 회전하고 설계하였다. 배종판에서 중간컵으로 이송된 마늘을 파종부의 파종컵에 받아 회전하면서 땅속에 파종컵이 묻히면 파종컵이 열리면서 땅속에 마늘을 심는 원리이다. 조간조정은 7조식의 경우 초기설치시 고정되도록 설계되었으며 농촌진흥청 기계화 표준재배안에 따라 의성마늘 기준 $14{\times}14cm$(조간${\times}$주간)를 기준으로 개발하였다. 조간조정은 기계가 설치되면 조정하기 어려우므로 14cm로 설계하였으며, 주간조정은 원형배종장치의 구동기어부의 속도비로 간격을 조정할 수 있도록 기어장치를 설계하였다. 주간조정은 13에서 18cm의 범위에서 작동하도록 설계되었으며, 필요에 따라 간격조절이 가능함. 마늘은 그 크기가 다르고, 형상도 다르기 때문에 종자에 따른 개별적인 파종기술들이 개발되어야하기 때문에 개발 기간이 오래 걸리고, 수익에 비하여 개발비가 과다하게 요구되는 실정인데 축적된 시뮬레이션 툴을 이용한 파종기 분석 기술을 확보할 경우 다른 파종기의 연구 개발에도 크게 도움이 될 것으로 기대되며, 생육측정 실험과 동역학 해석 툴 RecurDyn을 통해 파종기의 기구학적 분석을 통한 설계반영 인자를 도출할 계획이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8128-8139
• /
• 2015

Recently, the necessity of developing the load and resistance factor design(LRFD) for soft ground improvement method has been raised, since the limit state design is requested as international technical standard for the foundation of structures. In this study, to develop LRFD codes for foundation structures in Korea, target reliability index and resistance factor for static bearing capacity of driven steel pipe piles were calibrated in the framework of reliability theory. The 16 data(in Gwangyang) and the 57 data(Korea Institute of Construction Technology, 2008) sets of static load test and soil property tests conducted in the whole domestic area were collected along with available subsurface investigation results. The resistance bias factors were evaluated for the tow static design methods by comparing the representative measured bearing capacities with the expected design values. Reliability analysis was performed by two types of advanced methods : the First Order Reliability Method (FORM), and the Monte Carlo Simulation (MCS) method using resistance bias factor statistics. As a result, when target reliability indices of the driven pipe pile were selected as 2.0, 2.33, 2.5, resistance factor of two design methods for SPT N at pile tip less than 50 were evaluated as 0.611~0.684, 0.537~0.821 respectively, and STP N at pile tip more than 50 were evaluated as 0.545~0.608, 0.643~0.749 respectively. The result from this research will be useful for developing various foundations and soil structures under LRFD.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.117-124
• /
• 2017

A Smart Grid is a system that can efficiently use energy by exchanging real-time information in both directions between a consumer and a power supplier using ICT technology on an existing power network. DR(Demand response) is an arrangement in which electricity users can sell the electricity they save to the electricity market when the price of electricity is high or the power system is crisis. In this study, we developed a power meter data transmission device and power IT system that measure the demand information in real-time using a smart meter and transmit it to a cloud server. The power meter data transmission device developed in this study uses alight sensor connected to a Raspberry Pi 3 to measure the number of blinking lamps on the KEPCO meter per unit of power, in order to provide reliable data without any measurement errors with respect to the KEPCO power data. The power measurement data transmission device uses the standard communication protocol, OpenADR 2.0b. The measured data is transmitted to the power IT system, which consists of the VEN, VTN, and calculation program, via the LTE WiFi communication network and stored in its MySQL DB. The developed power measurement data transmission device issues a power supply instruction and performs a peak reduction DR when a power system crisis occurs. The developed power meter data transmission device has the advantage of allowing the user to adjust it every 1 minute, where as the existing smart metering time is fixed at once every 15 minutes.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.83-93
• /
• 1994

1886년 고트리브 다이믈러와 칼 벤즈가 가솔린 자동차를 개발한 이후 100여년이 지난 지금 자동차는 비약적으로 진보, 발전하여 현대 산업사회와 개인의 생활에 있어 산업운송수단과 이동수단으 로서 필요불가결하게 되어 밀접한 관계를 갖고 있다. 우리나라 자동차 공업의 역사는 자동차가 사회적, 경제적 효용에 따라 그 생산과 보유대수가 날이 갈수록 증가 일로에 있으며, 자동차의 생산대수는 전세 계에서 년간 약 50,606천대('94년)로서 중요한 국가 기간 산업으로 자리하고 있다. 한편 전기, 전자공업의 발전에 따른 자동차의 Car Electronics가 많이 채용되게 됨에 따라 현재의 자 동차에는 대부분이 전자제어 System으로 구성되어 있다. 최근에는 Micro Processor를 이용한 전자부품이 많이 사용되어 전자파에 대한 문제가 다양하게 발생 하고 있다. 예를 들면 미국 캘리포니아주에서 전자점화제어장치와 연료분사 장치를 설치한 구미의 자동 차가 주행중 28MHz, 28W의 아마추어 무선을 탑제한 자동차가 통과할 때 엔진이 고르지 못한 보고가 있 었고, 화학섬유로된 옷을 착용한 전자부품이 다른 부품에 영향을 주는 사례가 맣아지고 있다. 따라서 자동차에는 여러가지의 전장품, 전자기기를 탑재하기 때문에 자동차 자체에서 발생하는 것과 외부로 부터 받는 전자장해 EMI(Electromagnetic Interference), EMS(Electromagnetic Susceptibility) 가 문제로 되어 자동차 및 부품 maker에 의한 EMC(Electromagnetic Compatibility) 평가의 중요성이 고조되고 있다. 차제무전기, 차제무전기, Car-Radio는잡음방해를 많이 받기도 하지만, 잡음원이 되기 도 한다. 또한 Engine 제어, 차속제어, Brake 제어등에 이용되는 전자제품은 방해에 의한 오동작 또는 파괴가 발생하여 주행기능, 안전성에 문제가 야기되지 않도록 해야 한다. 이러한 전자기 환경은 모두 RF(Radio Frequence)와 자동차에서의 전자파 장해 문제의 원이 될 수 있다. 자동차 및 그 부품의 전자기 방해에 관한 규격화는 1987년부터 괄목할 만하게 진행되어 이에 따른 규제 움직임이 IEC(International Electrotechnical Commission: 국제전기기술위원회) 산하의 하부기 구인 CISPR(International Special Committeeon Radio Interference: 국제 무선 장해 특별위원회)가 전자기 방해파에 대한 측정법 통일안을 제안 하였고, ISO(International Standardization Organiza- tion: 국제표준화 기구) 가운데 TC 22/SC3가 자동차의 전장품에 대한 장해를 논의히고 있다. 특히, 자동차의 EMC에 관한 국가 규격은 국제 규격에서 저술한 바와 같이 특별히 규정된 것이 없고 VDE(Verband Deutscher Elektrotechniker: 서독전기기술 협회)와 SAE(Society of Automotive Engi- neers: 자동차 기술자 협회)에서 비교적 활발하고 Jaso(Japanese Automobile Standards Organization: 일본 자동차 표준협회)에서 많이 진행중에 있다. 본 고에서는 자동차의 전자제어에 따른 잡음 발생 요인과 전자파 간섭 관련 자동차 규격과 시험평가 방법에 대해 간단히 소개 하였다.