• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.533-549
• /
• 2017

In this study, drainage systems were proposed to drain the leakage of groundwater in the existing underground concrete structures. The system consists of drainage board, wire mesh, fixed nail, and mortar with mineral. In order to increase constructability, the drainage board and wire mesh were attached on the surface of cement concrete using the air nailer and fixed nail. The mortar with 30% of blast furnace slag was sprayed on the drainage board and wire mesh using the spray mortar equipment. The field test construction was carried out in a conventional concrete lining tunnel and concrete retaining wall for performance verification of the drainage system in the field. There was no problem with performance degradation in the drainage system for three years after construction. The bond strength tests were performed on the sprayed mortar at 14 days and about 3 years after field test construction. In case of attaching the wire mesh on the drainage board, the bond strengths of the sprayed mortar were 1.04 MPa at 14 days and 1.46 MPa about 3 years. In case of the drainage board without the wire mesh, the bond strengths of the sprayed mortar were 1.13 MPa at 14 days and 0.89 MPa, less than 1 MPa of bond strength criteria, about 3 years.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.535-543
• /
• 2009

This paper describes a design for RFID(Radio Frequency Identification) tag antenna using license plate attached the vehicle bumper in 900 MHz band. The proposed tag antenna size which is located on upper center position of a vehicle license plate is 162.5${\times}$40${\times}$1 mm$^3$. A resonant frequency of design antenna and the bandwidth which has return loss of -10 dB below are 900 MHz and about 720 MHz(640${\sim}$1,360 MHz), respectively. The commercial chip impedance considered on design was 16- j131 ${\Omega}$ and the complex conjugate impedance of chip was used as input impedance of tag antenna. The measured return loss and radiation pattern were agreed well with the calculated results. The measured readable range of the proposed tag antenna designed on only the vehicle license plate was 11.5 m. Moreover, its range of the fabricated tag antenna that the license plate and the vehicle bumper were fixed by volt and nut was observed 10.4 m. These measured readable range showed about 5 m above far distance more than the average readable range of commercial tag antenna.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.193-198
• /
• 2014

The purpose of this study is to see the feasibility of the newly developed 2D dosimetry system using phosphor screen for helical tomotherapy. The cylindrical water phantom was fabricated with phosphor screen to emit the visible light during irradiation. There are three types of virtual target, one is one spot target, another is C-shaped target, and the other is multiple targets. Each target was planned to be treated at 10 Gy by treatment planning system (TPS) of tomotherapy. The cylindrical phantom was placed on the tomotherapy table and irradiated as calculations of the TPS. Every frame which acquired by CCD camera was integrated and the doses were calculated in pixel by pixel. The dose distributions from the fluorescent images were compared with the calculated dose distribution from the TPS. The discrepancies were evaluated as gamma index for each treatment. The curve for dose rate versus pixel value was not saturated until 900 MU/min. The 2D dosimetry using the phosphor screen and the CCD camera is respected to be useful to verify the dose distribution of the tomotherapy if the linearity correction of the phosphor screen improved.

• Composites Research
• /
• v.37 no.3
• /
• pp.219-225
• /
• 2024

It is essential to develop a light-weight, high-performance structure for the deployable reflector antenna, which is the payload of a reconnaissance satellite, considering launch and orbital operation performance. Among them, the composite main reflector is a key component that constitutes a deployable reflector antenna. In particular, the development of a high-performance main reflector is required to acquire high-quality satellite images after agile attitude control maneuvers during satellite missions. To develop main reflector, the initial design of the main reflector was confirmed considering the structural performance according to the laminate stacking design and material properties of the composite main reflector that constitutes the deployable reflector antenna. Based on the initial design, four types of composite main reflectors were manufactured with the variable for manufacturing process. As variables for manufacturing process, the curing process of the composite structure, the application of adhesive film between the carbon fiber composite sheet and the honeycomb core, and the venting path inside the sandwich composite were selected. After manufacture main reflector, weight measurement, non-destructive testing(NDT), surface error measurement, and modal test were performed on the four types of main reflectors produced. By selecting a manufacturing process that does not apply adhesive film and includes venting path, for a composite main reflector with light weight and structural performance, we developed and verified a main reflector that can be applied to the SAR(Synthetic Aperture Rader) satellite.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.421-422
• /
• 2012

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.523-524
• /
• 2008

• Electric Engineers Magazine
• /
• v.186 no.2
• /
• pp.24-30
• /
• 1998

전력용 변압기의 단락임피던스를 현장에서 측정하기도 하며 명판이나 공장시험치와 비교 할수도 있다. 이러한 과정은 공장시험이 실시된 이후에 발생 할 수 있는 권선의 이동을 검출하기 위한 것이다. 권선의 이동은 보통 큰 고장전류 또는 운송이나 설치시의 기계적 손상으로 인하여 발생한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.649-650
• /
• 2008

• Journal of the Korean Vacuum Society
• /
• v.3 no.4
• /
• pp.401-404
• /
• 1994

초고 진공영역에서 배기특성 개선을 위하여 재질 및 구조가 다른 세가지 형태의 60(l/s) 형이온 펌프를 제작하여 그 배기특성을 측정하였다. 그 결과 음극판에 Ta 선을 전기용접한 펌프와 양극 cell의 구조에 변화를 준 펌프의 배기속도가 상용으로 이용되고 있는 펌프에 비해 약 50% 이상 개선되었다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.455-460
• /
• 1996

원자력발전소의 전열관 보수용접 기술 개발을 위해 Inconel 600 재질의 plate 판에 레이저 용접실험을 수행하였다. 레이저 발진기로 부터 발진된 레이저 빔은 광섬유를 통하여 전송되고, 집광렌즈군를 이용하여 용접이 이루어지도록 하였다. pulse 레이저 용접 변수인 펄스폭, 반복율, 첨두출력 및 용접속도를 변화시키면서 용접결과를 측정하였다. 이에 따른 적절한 용접범위를 제시하였다.