• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.463-467
• /
• 2016

In this paper, acceleration and pressure exerted on a human model were measured under a supersonic condition in a shock tunnel. In order to measure these in an interference-free environment, free-fall technique with an electromagnet and a three-dimensional iron-powdered human model was used. Free-fall experiment was conducted at Mach 4 and the force acting on the model was obtained by calculating the displacement from the flow visualization images.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.10a
• /
• pp.148-150
• /
• 2012

바람이나 파도에 의해서 요트 계류장과 요트 사이 또는 요트 계류장과 계류장 사이에는 충격이 발생하는데, 이러한 충격으로 인하여 계류장 또는 요트가 파손되거나 전복된다. 특히, 방파제 없이 외해에 설치한 요트 계류장은 이러한 위기에 항상 노출되어 있어 이에 대한 대책이 시급한 실정이다. 논문에서는 요트 계류장의 롤링, 히브, 핏칭 등의 운동을 측정하기 위한 하드웨어의 구축과 평가에 관해서 기술하였다. 하드웨어는 MEMS 기반 자이로와 가속도계 등의 관성 센서를 내장한 반도체 센서 SD746을 이용하여 구축하였고, 구축한 하드웨어를 이용하여 소형 요트 계류장에서 발생할 수 있는 운동을 수작업으로 생성하여 측정 및 평가하였다. 실험결과 x-축, y-축, z-축 등 3축 가속도와 3축 각속도 측정이 가능하여 요트 계류장의 운동 상태 모니터링이 가능함을 알았다. 본 연구는 추후 요트 계류장의 위기상태를 평가하고 통보하기 위한 시스템 구축에 이용할 예정이다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.2
• /
• pp.1-8
• /
• 2012

This paper presents the accelerometer which is a key component of TPMS(Tire Pressure Monitoring System). Generally a piezoresistive accelerometer has characteristics of lower cost, better linearity and better immunity about the environmnet noise than a capacitive one. Three types of piezoresistive accelerometers are degined and simulated using ANSYS program. The best one is a piezoresistive sensor which is supported by four beams located at the center of the edge of the mass after comparing the characteristics of resonant frequency of the three types. Considering the sensor size and a simulated maximum stress and maximum displacement, the length of beams is set as $200{\mu}m$. The size of a piezoresistive accelerometer is $3.0mm{\times}3.0mm{\times}0.4mm$. The sensor output is characterized by measuring the output characteristic depending on angle. As a result the offset voltage of the accelerometer is 43.2 mV and its sensitivity is $42.5{\mu}V/V/g$. The temperature bias drift is measured. The shock durability of the sensor is 1500g and the measuring range is 0 ~ 60 g.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.166-166
• /
• 2011

한국건설기술연구원내에 세계 최초로 UHPC(초고성능 콘크리트)를 활용한 보도사장교를 설계 및 시공하여 공용중이다. 초고성능 콘크리트(UHPC, Ultra High Performance Concrete)는 기존의 콘크리트의 단점을 극복하기 위하여 강섬유 및 혼화재료를 사용하여 고강도화와 더불어 인장강도, 휨강도, 균열에 대한 저항성, 전단강도 및 내충격성을 대폭 개선시켜서 구조부재의 연성 및 강도를 확보하기 위해 개발된 것으로서 한국건설기술연구원이 독자적 연구를 바탕으로 UHPC를 개발하였고, KICT-UHPC의 특성을 충분히 반영한 보도사장교를 한국건설기술원내에 실구조물로 시공하였다. 한국건설기술연구원내 본관 1, 2동 연결 보도사장교(SUPER BRIDGE 1)의 진동실험을 통해 UHPC 보도사장교의 동특성(고유진동수 및 모드형상)을 평가하였다. 대상교량에는 보도사장교의 캔틸레버 구조 특성에 의해 발생하는 진동을 제어하기 위한 질량 264kg의 난간형 수직진동제어장치(TMD) 4대가 설치되어 있으며, 부가질량의 운동을 기계적으로 구속하거나 구속을 해제하여 TMD의 작동을 켜거나 끌 수 있도록 되어있다. TMD의 가동 및 정지시 동특성을 비교하는 정밀한 검증 실험을 통하여 TMD 설치에 의한 동특성의 변화도 평가하였다. 가진망치에 의한 충격실험으로부터 획득한 가속도 시간이력 데이터와 가진망치의 가진력 시간이력 데이터를 사용하여 주파수응답함수(FRF, frequency response function)를 계산하고, 이로부터 Super Bridge I의 동적모드형상과 고유진동수를 추출하였다. 1차 모드의 고유진동수는 TMD 정지시 2.2949 Hz, TMD 작동시 2.0996 Hz로서 8%정도 감소하였다. 충격해머에 의한 가진 실험을 통해 세계 최초로 시공한 UHPC 보도사장교의 진동특성과 관련한 신뢰성 있는 자료를 확보할 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.307-313
• /
• 2009

In general, pyroshock is generated from the actuation of separation devices for several stage, fairing, and satellite separation in the flight of a launch vehicle. During these events, transient vibration phenomenon called pyroshock, which shows large acceleration in the high frequency range, occurs and it can result in the malfunction of electronic components which is equipped inside the launch vehicle or satellite. In this paper, mesh washer isolators made out of SMA were introduced for the isolation of pyroshock. One type of isolator primarily used pseudoelastic characteristics of SMA and the other type of isolator used shape memory effect of SMA. For the study of basic load-displacement relationship of each SMA isolator, compressive loading tests were performed and the results showed the capability of the isolator itself. Pyroshock isolation tests were followed and verified the outstanding isolation performance of isolator. In addition, random vibration tests were also performed and checked the dynamic characteristics of each SMA isolator.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1125-1131
• /
• 2016

The purpose of this paper is to establish an evaluation criteria for pavement condition in bicycle road. The suggested criteria would help in the activation policy of bicycle use. The conventional evaluation criteria is difficult to be applied for the bicycle road since the bicycle road is sensitive to changes in the driving environments such as obstacles and bumps. This study presents the evaluation criteria that is suitable for bicycle road. The criteria was suggested in 5 grades through the impact acceleration range of RMSI (Road Monitoring System using ICT). The grades of the criteria are divided into a range of grade A to E. The grade A is a very good condition, while the grade E is a state that requires immediate maintenance. This study were confirmed the validity through the survey of user's satisfaction. According to the results of survey, the grade A was shown correlation of 91%. The grade E requiring immediate repair was presented correlation of 94%. It showed that the results of surveying the bicycle road users are highly correlated with the suggested criteria for pavement condition. It showed that the criteria are highly correlated with the survey results. Suggested criteria using the RMSI is expected to be effective for maintenance of the bicycle road. In addition, it is expected to ensure the serviceability and safety for the bicycle users.

• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.282-288
• /
• 2011

One of the most challenging issues facing shallow seismic survey is how to generate large amplitude of high frequency signal with small seismic sources. We tested the performance of the most commonly used shallow seismic source, hammer, with four plates: PE, nylon, aluminum, and steel plates. We compared their signal powers in terms of impulsive forces, accelerations, and ground vibration velocities caused by hammer impacts. According to a previous work, hammer blowing to an aluminum plate would generate the largest amplitude among four combinations. However, it was found in this experimental research that aluminum plate delivers seismic wave energy to the ground less than that generated with steel or PE plate. Even though the amplitude is relatively small, plastic plates could provide seismic pulses of 180 ~ 200 Hz in the bandwidth, and it seems to be very hard to generate seismic energy over the frequency of 250 Hz.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1615-1626
• /
• 1992

In this study, vibrations and resulting acoustic radiations from an elastic beam impacted by a steel ball were studied theoretically and experimentally. First the transverse vibrations of free-free elastic beams are analysed with modal analysis technique. The impact forces are modeled with the Hertz's theory and the contanct duration is compared with the measured values. Also the calculated beam vibrations are verified with the experimental results. Then the acoustic radiations due to the beam vibration are studied numberically and experimentally. The acousticpressure is calculated assuming the beam has an elliptical cross-section. The predicted acoustic pressure is compared with the measured value. It was found that both the predicted beamvibrations using the Hertz's theory and the estimated acoustic pressure under the assumption of an elliptical cross- section are in very good agreements with the measured values.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.301-306
• /
• 2016

In bridge performance assessments, a new load carrying capacity evaluation model of simple bridges was proposed, which is based on the developed simple support impact factor spectrum. In this paper, a conservative assumption that the inner span with the both ends fixed boundary condition is ideal for applying the impact factor response spectrum for continuous bridges. The impact factor response spectrum has been proposed based on this assumption. The response spectrum by comparing the numerical analysis result and actual measurement data verified the applicability. The analysis was loading the moving load of DB-24 in a six-span continuous bridge, which was the same as the actual measurement data, the dynamic response was measured in the fourth span. The frequency of the bridge was obtained by FFT on the acceleration response and the span-frequency of sample bridge was calculated by the frequency. The impact factor of the sample bridge was determined by applying the span-frequency of the bridge to the proposed response spectrum; it was similar to the result of comparing the actual measured impact factor. Therefore, the method using the impact factor response spectrum based on the frequency response of both ends-fixed beam was found to be applicable to an actual continuous bridge.

• Journal of the KSME
• /
• v.29 no.2
• /
• pp.175-183
• /
• 1989

오늘날 널리 연구되고 있고 공학자들에게 많은 관심을 끌고있는 압전 세라믹(ceramic)을 이용 하여 자연계에서 일어나는 각종 진동현상을 측정하고 해석하기 위한 센서(sensor)의 설계, 제작은 이미 선진국에서도 보편화된지 오래이다. 특히 압전형 가속도계(piezo type accelerometer)는 진동의 절대 측정에 가장 유용한 센서로 널리 알려져 있다. (1) 아주 넓은 사용 주파수 범위 (2) 넓은 동적범위(dynamic range)에 걸친 뛰어난 선형성(linearity) (3) 측정된 가속도 신호를 전기적으로 적분하여 속도와 변위에 대한 자료 제공 용이 (4) 높은 정확성 (5) 자발 전(self-generating)이므로 외부 전원 공급이 불필요 (6) 수명과 뛰어난 내구성 (7) 작은 크기와 가벼운 무게 등이다. 현재 기계 구조물 진동 측정에 이용되고 있는 스트레인 게이지 형(strain gage-type)의 가속도계는 감도가 좋고 저주파 진동 측정에는 편리한 반면 충격이나 높은 주파수 전동 측정에는 적합하지 않으며 내부 구조가 다소 복잡하다(2). 반면에 압전형 가 속도계는 압전 소자와 관성 질량의 조합 설계로서 저주파 진동 측정에 적합한 고감도의 가속도 계와, 감도는 떨어지나 아주 높은 주파수 범위의 진동까지 측정이 가능한 가속도계를 손쉽게 설계, 제작할 수 있다. 본 글에서는 선진국에 비해 낙후된 국내의 센서 설계, 제작 기술을 고 양시키고자 최근 한국과학기술원에서 시도된 압전형 가속도계의 개발 연구 사례를 중심으로 설계 및 제작시 고려 사항과 보정 문제를 소개하고자 한다.