• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.5384-5391
• /
• 2011

본 논문에서는 RCO 반응기의 최적 조업 조건을 도출하고자 현재 조업 중인 RTO 반응기 촉매층의 압력분포, 유속분포, 유선장, 체류시간, 온도분포 등에 대하여 분석하였고 최적의 조업 조건을 도출하기 위한 전산유체해석을 수행하였다. 전산 해석 결과, 현재 조업중인 반응기 촉매층의 축열재로 인한 압력손실은 크지 않은 것으로 나타났으며, 세라믹 필터 이후 유속은 1.8~2.7 m/s로 특별한 편류없이 비교적 안정적 유속분포를 보이고 있었다. 기류분포를 좀 더 개선하려고 한다면 설비 내부에 플래넘과 촉매층 접속 구간 연장 등의 방법을 고려할 수 있을 것으로 판단된다. 그러나 기류 안내판이나 다공판 부착 등의 방법은 큰 효과는 없을 것으로 나타났다.

• 태양에너지
• /
• 제19권2호
• /
• pp.57-65
• /
• 1999

[ $H_2O$ ]-NaCl혼합물을 냉축열재로 선택하였으며, 이 혼합물의 상변화온도를 몰농도 변화에 의하여 조절하였다. 그리고 고농도와 저농도의 NaCl과 $H_2O$가 ion-dipole interaction으로 결합하는 구조를 그림으로 가시화하고 가열, 냉각과정에서 $H_2O$-NaCl이 동결, 융해하는 현상을 도시하므로서 융해와 동결과정에서 상변화온도가 2단계로 나타나는 구조적 원인을 구명하였으며, NaCl의 농도변화에 따른 상변화온도를 이론적으로 분석하므로서 실험 및 이론분석 결과의 타당성을 증명할 수 있도록 하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.618-623
• /
• 2004

This paper has dealt with the heat storage characteristics of gel type micro size latent heat storage material slurry. The heat release operation to the gel type micro size latent heat storage material slurry was carried out using hot air bubbles by direct contact heat exchange. This experiment was carried out using phase change material of n-paraffin so the heat release amount is higher than cold water system. The parameters of this experiment were concentration of latent heat phase change material, height of heat release bath and inlet velocity of hot air. The main results obtained are as follows : (1) The effect of concentration of latent heat phase change material dispersed with water is very affective to the direct contact heat exchange between hot air and gel type micro size latent heat storage material slurry. (2) It is clarified that the most effective concentration of latent heat phase change material dispersed with water exists around 20mass% at this type of direct heat exchange model experiment.

• Journal of Biosystems Engineering
• /
• 제30권4호
• /
• pp.195-201
• /
• 2005

The output of Stirling engine is influenced by the regenerator effectiveness. The regenerator effectiveness is influenced by heat transfer and flow friction loss of the regenerator matrix. In this paper, in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed method of matrix in the oscillating flow as the same condition of operation in a Stirling engine. As matrices, several kinds of combined wire screen meshes were used. The results are summarized as follows; The packed meshes with high mesh no. in the side of heater part of regenerator showed effective than the packed meshes with low mesh no. in the side of cooler part of regenerator. The temperature difference and pressure drop of the regenerator were not made by the specific surface area of wire screen meshes but by the minimum free-flow area to the total frontal area. Among the No. 150 single screen meshes, 200-60 combined meshes, the 200-150-100 combined meshes showed the highest in effectiveness.

• 헤리티지:역사와 과학
• /
• 제22권
• /
• pp.348-355
• /
• 1989

고성능 핵자탐기를 이용하여 1988. 6. 11부터 6. 30까지 충남 공주 송산리 고분군의 탐사를 수행했다. 고분탐사의 표본으로 이미 알고 있는 전축분 6호분과 석축분 5호분을 동시에 탐사결과 백제당시 높은 온도로 구어 만든 벽돌로 축성된 6호분에서는 5호분보다 아주 강한 고지자기반응을 보여주었다. 그리고 탐사지역 Ａ지역과 Ｄ지역에서는 고지자기반응이 어떠한 일정한 양상을 따라 나타났다. 이들은 각각 석열(石列) 혹은 석축열(石築列)였음을 발견했다. 또한 Ｄ지역의 강한 고지자기 반응에서는 백제시대의 토기항아리가 발견되었다. 이번 탐사의 결과로 고지자기탐사는 높은 열처리와 관계된 고고학적 유적, 유물탐사에 매우 유리하다는 것을 알게 되었다.

• Journal of Biosystems Engineering
• /
• 제30권4호
• /
• pp.202-209
• /
• 2005

The output of Stirling engine is influenced by the regenerator effectiveness. The regenerator effectiveness is influenced by heat transfer and flow friction loss of the regenerator matrix. In this paper, in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed method of matrix in the oscillating flow as the same condition of operation in a Stirling engine. As matrices, 6 kinds of steel wires, 4 kinds of combined steel wires, 8 kinds of combined steel wires with screen meshes were used. The results are summarized as follows; Among 6 kinds of steel wires $({\phi}0.7\;mm,\;{\phi}0.9\;mm,\;{\phi}1.2\;mm,\;{\phi}\;1.6\;mm,\;{\phi}2.0\;mm,\;{\phi}2.7\;mm),$ the two steel wires $({\phi}0.7\;mm,\;{\phi}0.9\;mm)$ showed the highest in effectiveness. Among 4 kinds of combined steel wires $({\phi}l.6-{\phi}l.2\;mm,\;{\phi}1.2-{\phi}l.6\;mm,\;{\phi}0.9-{\phi}l.2\;mm,\;{\phi}l.2-{\phi}0.9\;mm),\;the\;{\phi}1.2-{\phi}0.9\;mm$ showed the highest in effectiveness. Among 8 kinds of combined steel wires with screen meshes $(150-{\phi}0.9\;mm,\;150-{\phi}l.2\;mm,\;{\phi}0.9\;mm-150,\;{\phi}1.2\;mm-150,\;150-{\phi}0.9\;mm-150,\;150-{\phi}1.2\;mm-150,\;150-{\phi}l.6\;mm-150,\;150-{\phi}2.0\;mm-150),\;the\;{\phi}l.2\;mm-150$ showed the highest in effectiveness.

• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.529-536
• /
• 2002

The performance of stilting engine, in particular, its energy conversion efficiencies are critically influenced by the regenerator characteristics. The regenerator characteristics are influenced by effectiveness, void fraction. heat transfer loss and fluid friction loss in the regenerator matrix. These factors were influenced by the surface geometry and material properties of the regenerator matrix. The regenerator design goals arc good heat transfer and low pressure drop of working Bas across the regenerator. Various data for designing a wire screen matrix have been given by Kays and London(1984). The mesh number of their experiment. however, was confined below the No. 60. which seems rather small for the Stirling engine applications. In this paper. in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed mettled of matrix in oscillating flow as the same condition of operation in a Stirling engine. Seven kinds of sing1e wire screen meshes were used as the regenerator matrices. The results are summarized as follows; 1. While the working fluid flew slowly in the regenerator. the temperature difference was great at the both hot-blow(the working fluid flows from healer to cooler) and cold-blow(the working fluid flows from cooler to healer). On the other hand. while the working fluid flew fast. the temperature difference was not distinguished. 2. The No.150 wire screen used as the regenerator matrix showed excellent performance than tile others. 3. Phase angle variation and filling rate affected heat transfer or regenerator matrices. 4. Temperature difference between the inlet and outlet of the regenerator is very hish in degree of 120 phase angle.

• 태양에너지
• /
• 제12권1호
• /
• pp.59-71
• /
• 1992

본 연구는 주거용건물에서의 난방용에너지 소비량절감 및 실내환경의 쾌적도 향상을 목적으로, 잠열재 용기의 축열 및 방열특성을 파악한 후, 잠열저장패널을 이용한 바닥난방공간의 실내온도분포를 분석하였다. 잠열저장패널의 특성을 구명하기 위해서는 패널의 가열시간에 따른 잠열재의 융해 및 응고특성에 대해 실험 분석하고 실험건물을 이용하여 잠열저장패널을 설치한 실내공간의 온도분포에 대해 실험 분석하였다.

• 설비공학논문집
• /
• 제15권5호
• /
• pp.352-359
• /
• 2003

The present study has been conducted for manufacturing MPCM (microencapsulated phase change material) slurry with in-situ polymerization and proving their applicabilities for tooling system. The surface of MPCM is composed of melamine, while tetradecane, paraffin wax, is centered in the MPCM. The produced capsules are observed by the optical microscope and SEM for superficial shapes. Their thermal properties are measured by DSC. Their size distributions are observed by FA particle analyzer. A narrow size distribution from 1 to 10 ${\mu}{\textrm}{m}$ with 5 ${\mu}{\textrm}{m}$ of average diameter was observed. Melting temperature was 6.7$^{\circ}C$. The durability of MPCM was tested with various types of pump such as centrifugal, peristaltic, and mono pumps. During 10000 cycles the fraction of broken capsules was smaller than 6% for the centrifugal and peristaltic pumps, while bigger value of 8% for the mono pump. A cooling system, which adopted MPCM slurry as a media for transporting cold thermal energy, was designed to investigate the performance of the MPCM. The discharging times of 10 and 20 wt% MPCM slurry were lasted up to 105 and 285 minutes longer, respectively, than the water cooling system.

• 한국연소학회지
• /
• 제8권1호
• /
• pp.17-24
• /
• 2003

The conventional regenerative system has a high thermal efficiency as well as energy saving using the high preheated combustion air. in spite of these advantages, it can not avoid high nitric oxide emissions. Recently, flameless combustion has received much attention to solve these problems. In this research, numerical analysis is performed for flow-combustion phenomena in the self regenerative burner. In this analysis we used Fluent 6.0 code. the that is developed for commercial use, Methane gas is used as a fuel and two-step reaction model for methane and Zeldovich mechanism for NO generation are used. the velocity of the preheated combustion air is used as a parameter and we analyze the characteristics of flow-field, temperature distributions and NO emissions. Due to the increased recirculation rate, the maximum temperature of flame is significantly increased and NOx emissions is reduced.