• Polymer Science and Technology
• /
• v.11 no.5
• /
• pp.623-633
• /
• 2000

• Korean Journal of Human Ecology
• /
• v.16 no.4
• /
• pp.801-811
• /
• 2007

This study attempts to propose a pattern design of snug fitting midi briefs for women. Each briefs made of two kinds of fabric, cotton 40's and cotton 40's spandex, was produced for the research in a different shrinkage rate. The result of wearing test of the briefs-sold-in-the-market (BSM) and the briefs-specially-made-for-this-research (BSMR) were as follows: BSMR showed a higher mark than that of BSM in the sense of close fit on the torso, comfortableness, sense of being tight, satisfaction and beauty. In particular, the back design line of BSM gave a lower satisfaction to test wearers, while that of BSMR gave a more comfortableness to them, making their hip comfortably being wrapped by making smoother the angle of the straight line linking sidelines with clutch part, and making sidelines into curve. In a forward research, further studies about grading and other patterns but midi pattern of briefs would be examined.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.1
• /
• pp.102-109
• /
• 2003

The purpose of this study was to evaluate the linear polymerization shrinkage(%) and microhardness of composite resin(Z-100, 3M, USA) according to 2-step light curing method. Conventional light curing unit(Curing Light 2500, 3M USA) and 2-step light curing unit(Elipar Highlight, ESPE, Germany) were used as light source. The strain gauge method was used for determination of polymerization shrinkage(%). Samples were divided by 3 groups according to light curing methods (Group I : $450mW/cm^2$, 40sec, Group II : $650mW/cm^2$, 40sec, Group III : $150mW/cm^2$, 10sec & $650mW/cm^2$, 30sec). Preparations of acrylic molds were followed by filling and curing. Strain gauges attached to each sample were connected to a strainmeter. Measurements were recorded at each second for the total of 10 minutes including the periods of light application. And microhardness of each group after 24hours from light irradiation were measured. Obtained data were analyzed statistically using Ore-way ANOVA and/or Scheffe test. The results of the present study can be summarized as follows: 1. Composite resin in acrylic molds showed the initial expansion at the early phase of polymerization. This was followed by the contraction with the rapid increase in volume during the first 60 seconds and gradually diminished as curing process continued. 2. The lowest linear polymerization shrinkage(%) was found in group III followed by group I, II during the measuring periods. 3. Group III using 2-step curing method showed statistically significant reduction of linear polymerization shrinkage(%) compared with group I, II at 1 minute and 10 minutes from light irradiation(p<0.05). 4. The microhardness values of each group not revealed significant difference.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.327-338
• /
• 2014

Relationship between growth rate and wood quality was investigated by physical and mechanical properties with Quercus rubra (24 years old) from five different origin of apricot. In greenwood moisture content, sapwood had higher moisture content than heartwood, and there was difference among different origin of apricot. There were different specific gravity of wood among different origin of apricot. Compared with higher growth rate with higher specific gravity in sapwood, opposite trend was observed in heartwood. There were difference in shrinkage based on origin of apricot, and higher growth rate wood had higher shrinkage and T/R ratio. Compression Young's modulus, bending strength, bending Young's modulus, and compact strength was difference among different origin of apricot. Higher growth rate wood had higher tensile strength, and also there was difference amont different origin of apricot. In hardness, 3 different directions had all difference among different origin of apricot, and higher growth rate wood showed higher hardness than others. Based on overall physical and/or mechanical properties and growth rate, apricot from Bancroft was best quality in current.