• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.182-183
• /
• 2009

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.98-103
• /
• 2015

A flow passage opening device utilizing an acceleration follow-up technique allows fuel to flow continuously through a pressurized fuel tank system. It is very difficult to test the device in a real flight situation because of severe test condition and a cost problem. In this paper, therefore, the results of a basic negative g test conducted by low-speed airplane are compared with RecurDyn simulation. Dynamic behavior of the device in total flight profile of a high-speed vehicle is also analyzed by using RecurDyn to predict its performance.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.4
• /
• pp.297-306
• /
• 2007

Model reference control is control method such that overall response of a plant plus controller approaches that of a given reference model. The reference model provides desired trajectory the plant should follow. There are many kinds of control methods in MRC. However, this paper focuses on Model Reference Sliding Mode Control. The plant of these controls is an uncertain and linear system varying in time, of second order, and with SISO. In this paper, a design scheme of reference model is proposed for MRSMC. The scheme determines reference model based on the information on bounded control inputs, reference inputs and system parameters. It is used to choose a Fixed Reference Model in the process of controller design, to update Variable Reference Model when stepwise reference inputs change and to update Instant Reference Model at every sampling time. The simulation results show that the proposed method yields better control performance than the conventional MRC subject to the stepwise reference input when applied to the position control system for motor system.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.4
• /
• pp.107-121
• /
• 2017

This study conducted a 3-stage survey and simulation experiment to identify the impact of vehicle platoons on car-following behavior of manually-driven vehicles. Vehicle maneuvering data obtained from driving simulations was statistically analyzed based on three measures including average speed, acceleration noise, and offset to represent the deviation of lateral movements. Results indicate that MV drivers tended to have psychological burden while driving in automated vehicle platooning environments, which resulted in different vehicle maneuvers. It is expected that the outcome of this study would be useful fundamentals in developing various traffic operations strategies for managing mixed traffic stream consisting of MVs and autonomous vehicles.

• Journal of Internet Computing and Services
• /
• v.14 no.6
• /
• pp.33-39
• /
• 2013

When the eldery with limited mobility and disabled use a wheelchairs to move, it can cause decreased exercise ability like decline muscular strength in upper limb and lower extremities. The disabled people suffers with spinal cord injuries or post stroke hemiplegia are easily exposed to secondary problems due to limited mobility. In this paper, We designed intelligent wheelchair robot system for upper limb and lower extremities exercise/rehabilitation considering the characteristics of these severely disabled person. The system consists of an electric wheelchair, biometrics module for Identification characteristics of users, upper limb and lower extremities rehabilitation. In this paper, describes the design and configurations and of developed robot. Also, In order to verify the system function, conduct performance evaluation targeting non-disabled about risk context analysis with biomedical signal change and upper limb and lower extremities rehabilitation over wheelchair robot move. Consequently, it indicate sufficient tracking performance for rehabilitation as at about 86.7% average accuracy for risk context analysis and upper limb angle of 2.5 and lower extremities angle of 2.3 degrees maximum error range of joint angle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.573-577
• /
• 2009

Dynamic behavior simulation of supersonic engine was performed and PI control algorithm was studied for the buzz control in the inlet and the thrust control. Firstly, required thrust was tracked according to the fuel flow control and then inlet pressure was regulated through the nozzle throat area control so that the buzz margin has the positive all the time. The control was performed according to the change of flight Mach number, altitude and angle of attack. The proportional gain and the integral gain for regulating the buzz margin was induced and simulated. In the results, it was confirmed and satisfied that control target in the operating area was changed the angle of attack from $0^{\circ}$ to $10^{\circ}$ at the flight Mach number of 2.1~3.0.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.817-823
• /
• 2017

In the past, research has been conducted on the development of an adaptive cruise control algorithm considering fuel efficiency, and an adaptive cruise control system considering fuel efficiency have been developed. However, research on optimizing vehicle and adaptive cruise control parameters in order to maximize performances is insufficient. In this study, the design optimization of vehicle and control parameters considering fuel efficiency, trackability, ride comfort and safe distance is performed. This paper proposes performance measures of vehicle behavior and develops an adaptive cruise control system. In addition, based on the screening of vehicle parameters that significantly influence performances, kriging surrogate models are constructed through a sequential design of experiment, and kriging surrogate model-based design optimization is performed to maximize fuel efficiency and satisfy target performances.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.31-39
• /
• 2012

This study aims to suggest a methodology of localizing and calibrating parameters, such as acceleration, deceleration, and lane changing which are the basis of car following model in interrupted traffic flow to overcome the limitation of origin and destination based transportation simulation and to verify the application of activity-based model for use in Korean roadway condition in a large scale area or a city. Especially, we figured out that a proper cell size reflecting Korean traffic conditions is 1.0m rather than 7.5m which is default size and a methodology of tracking vehicle behavior characteristics through tracking vehicle ID is suggested on this study. In addition, vehicle running characteristics in real interrupted traffic flow is analyzed through subdividing vehicle types and updating vehicle type ratio. For verification of suggested model, some portion of Dalgubyul-ro in the Daegu city is tested, and the possibility of realization of interrupted traffic flow in simulation is studied.