• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.4
• /
• pp.393-399
• /
• 2017

In a reciprocating compressor, the piston and connecting rod are important parts. Excess mechanical stress on these parts may cause damage, and broken parts are expensive and difficult to replace. Therefore, it is necessary to analyze the mechanical stress affecting durability and longevity. The main purpose of this study was to identify locations of maximum stress on pistons and connecting rods. Based on dynamic calculation of the working process of a specific air compressor, an analysis of piston and connecting rod performance has been completed. A three-dimensional model for the air compressor's pistons and connecting rods was built separately, and FEM analysis of these components was carried out using a numerical method. The pistons were loaded by pressure which was changed according to crankshaft angle without thermal boundary conditions. The simulation results were used to predict and estimate stress concentration as well as the value of this stress on pistons and connecting rods. The maximum equivalent stress calculated are over 190 MPa on pistons and 123 MPa on connecting rods at crank angle $135^{\circ}$ and $225^{\circ}$ but these are under tensile yield strength. Besides, the calculated safety factors of connecting rods and pistons is higher than 1. Moreover, the results obtained can be used to provide manufacturers with references to optimize the design of pistons and connecting rods for reciprocating compressors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3455-3459
• /
• 2014

This paper reports the design and experiments for a high drive force of projectile in a coil gun system. Currently, the coil gun has been studied to apply an electromagnetic launcher. A coil gun launches a projectile by the attractive magnetic force of the electromagnetic coil. The drive force of projectile is proportional to the magnetic force generated by the electromagnetic coil. The current affects the life of the coil and the current limit exists. Therefore, the coil gun design, which does not exceed the current limit and the magnetic forces are at the maximum, is required. For this purpose, this study calculated the magnetic flux density and forces of the coil gun system and determined the current limit of the coil using the Onderdonk's equation. Based on the design result, a prototype was manufactured and an experiment was conducted to measure the muzzle velocity of the projectile. The fired projectile was analyzed using a CCD camera, and the muzzle velocity was 21m/s. In addition, a comparison of the experimental value and analysis value using commercial electromagnetic analysis software MAXWELL revealed an error of approximately 9.5%.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.288-289
• /
• 2000

SBN, BSKNN KNSBN 등의 tungsten-bronze 계열에 속하는 광굴절 결정은 짧은 파장에서 좋은 감광도와 빠른 응답시간을 갖는다. 이중에서도 KNSBN 결정은 큰 크기의 결정 성장 및 도핑이 용이하고 광굴절 결정에서 중요한 특성 중 하나인 열 안정성(thermal stability)이 좋기 때문에 빠른 응답특성이 요구되는 응용분야에서 촉망받는 매질이다. 본 논문에서는 광정보저장, 광정보처리, 광컴퓨터, 광통신과 같은 다양한 분야에서 응용가능성을 가지는 Cu가 0.04wt.%도핑된 5mm$\times$5mm$\times$5mm 크기의 KNSBN 결정을 이용한 광신호의 증폭기술에 대하여 연구하였다. 먼저 Cu-KNSNB 결정의 2광파 결합 특성을 분석하기 위하여, 기록 파장에 따른 지수이득계수의 외부입사각의존성, 최대 지수이득계수를 나타내는 외부입사각에서 입사빔의 세기비에 따른 2광파 결합 이득을 측정하였다. 또한, 632.8nm파장 영역에서 기록 및 삭제시간 상수, 회절 효율의 입사빔 세기비 의존성을 측정하였다. 그리고, 음향-광학 변조기(AOM: acousto-optic modulator)에 의해 진폭 변조된 신호빔을 이용하여 광신호 증폭특성을 분석하고 그 결과를 제시하였다. 이때 두 빔의 입사각은 최대 지수이득계수를 나타내는 입사반각 12$^{\circ}$로 고정하고, 감쇄기를 이용하여 신호빔의 세기를 조절하면서 신호빔의 차동이득을 측정하였다. 투과된 신호빔은 같은 주파수에서 차동 이득(diffrerential gain)을 보였으며, 이는 moving grating과 시간-변조된 신호빔(또는 펌프빔)사이의 새로운 상호작용은 광굴절 결정의 시간 적분 특성에 의한 것이다. (중략) 경우는 상온에서 펌프 펄스의 유지시간이 0.5% 인 경우 레이저가 동작하는 것을 보여주었다. 이는 구조내에서 열전도가 문제가 된다는 것을 의미하는데 위아래가 공기로 둘러 싸여 있어 발생한 열이 가는 유전체 네트웍을 통해서만 전달 될 수 있기 때문이다. (중략)$^4$A$_2$에 의한 nophonon line R$_1$, R$_2$(680.4, 678.5 nm) 및 $^2$T$_1$$\longrightarrow$$^4$A$_2$(655.7, 649.3, 645.2 nm)의 형광방출 스펙트럼을 얻었으며, 형광수명은 0.264 ms로 조사되었다. 제조된 레이저 발진봉은 직경 6.3 m, 길이 45 nm이었다.\pm$0.06kHz Ge $F_4$; -1.84$\pm$0.04kHz$0.04kHz/TEX>0.04kHz 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다.

• KIISE Transactions on Computing Practices
• /
• v.21 no.2
• /
• pp.126-131
• /
• 2015

As flash-based storage systems have been actively employed in large-scale servers and data centers, reliability has become an indispensable element. One promising technique for enhancing reliability is static wear-leveling, which distributes erase operations evenly among blocks so that the lifespan of storage systems can be prolonged. However, increasing the capacity makes the processing overhead of this technique non-trivial, mainly due to searching for blocks whose erase count would be minimum (or maximum) among all blocks. To reduce this overhead, we introduce a new randomized block selection method in static wear-leveling. Specifically, without exhaustive search, it chooses n blocks randomly and selects the maximal/minimal erased blocks among the chosen set. Our experimental results revealed that, when n is 2, the wear-leveling effects can be obtained, while for n beyond 4, the effect is close to that obtained from traditional static wear-leveling. For quantitative evaluation of the processing overhead, the scheme was actually implemented on an FPGA board, and overhead reduction of more than 3 times was observed. This implies that the proposed scheme performs as effectively as the traditional static wear-leveling while reducing overhead.

• The Journal of Engineering Geology
• /
• v.8 no.1
• /
• pp.75-86
• /
• 1998

Eighteen oriented samples from the Jeongsun limestone of the Joseon Supergroup are collected. The orientations of C-axis of calcite and e twin plane, the average thickness, numbers of twins and the widths of calcite grains in 10 samples are measured. Then, the twin strain, mean width, intensity of twin and relative magnitude and orientations of principal stresses are calculated using Calcite Strain Gauge program. Twin strain, mean width and intensitv rainge between 0.801%~10.927%, $0.43{\mu\textrm{m}}~2.03{\mu\textrm{m}}$, and 33.5~113.4twim/mm, respectively. Metamorphic temperatures calculated from twin show below $70^{\circ}C$, indicating that twins were developed within 2.3km depth. In five samples, two events with different orientations of principal stress produced calcite twins, while only one event produced calcite twins in five samples. The direction of the maximum stress is almost horizontal and the minimum is almost vertical, indicating that the stress regirne is identical with thrust fault. E-W and NW-SE are the most dominant directions of comressive stress and N-S and NE-SW directions are also shown. Comparision between paleostress orientations measured in the study and others indicates that the maximum horizontal stress oriented to E-W may represent the paleostress of period either from the Silurian to the Triassic or from the Silulian to the Permian. Paleostress oriented to NW-SE may be the major direction of stress during the Daeho orogeny.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.369-379
• /
• 2011

The application of appropriate rehabilitation works can improve productivity and water quality of clogged wells, with extending the operation of the wells for a certain period. This study verified rehabilitation effect of the clogged wells by means of explosive method and air brush surging and by using hydraulic tests, water quality, and geophysical logs (optical and acoustic televiewer logs) before and after the cleaning works on the two wells drilled in bedrock in Mt. Geumjeong, Busan City. Air-brush surging method resulted in maximum 273% increase of the productivity with the concentration of $F^-$, $SiO_2$, and a decrease of turbidity and the concentration of $Cl^-$, $NO_3^-$. The explosive method resulted in maximum 156% increase of the productivity with an increase of the concentration of $F^-$, $SiO_2$ and a decrease of turbidity, $Cl^-$, $NO_3^-$.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.3
• /
• pp.135-142
• /
• 2015

Floating offshore structures should be designed by considering the most extreme environmental loadings which may be encountered in their design life. The most severe loading on a wave-offshore wind hybrid power generation system is wave loads. The principal parameters of wave loads are wave length, wave height and wave direction. The wave loads have different effects on the structural behavior characteristic depending on the combination of wave parameters. Therefore, the process of investigation for critical loads based on the individual wave loading parameter is need. Namely, the equivalent design wave should be derived by finding the wave condition which generates the maximum stress in entire wave conditions. Through a series of analysis, an equivalent regular wave height can be obtained which generates the same amount of the hydrodynamic loads as calculated in the response analysis. The aim of this study is the determination of equivalent design wave regarding to characteristic global hydrodynamic responses for wave-offshore wind hybrid power generation system. It will be utilized in the global structural response analysis subjected to selected design waves and this study also includes an application of global structural analysis.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.1
• /
• pp.46-62
• /
• 1989

This paper presents the results of full-scale structural measurements of 4,800 unit pure car carriers "HYUNDAI NO.103" and "HYUNDAI NO.105" on one voyage respectively for each ship, especially in order to investigate the local strength of partial bulkhead above free-board deck. With the measured data, the short-term frequency analyses have been performed. The results show that the wave-induced stresses follow, on the whole, well the Rayleigh distribution. In addition, it has been found from the measured data that transverse local stresses at bulkhead section have a very close relation with the acceleration in athwartship direction. Finally, the long-term analysis has been attempted by using the following two statistical distributions mainly in order to estimate the maximum stress amplitude at the corners of partial bulkhead. 1) Exponential distribution of cycles of stress amplitude 2) Double exponential distribution of extreme values of stress amplitude for each short-term analysis The results of these two cases show a good agreement with each other. For example, the estimated maximum stress amplitude for 10 years at port-side corner of Fr. 132 partial bulkhead is $2125kg/cm^2$ for the first case and $2170kg/cm^2$ for the second case just based on the measured data.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.2
• /
• pp.113-119
• /
• 2011

Safe operation and maintenance of engineered dry storage systems for spent fuel from nuclear power plants basically depends on adequately adopted design requirements. The most important design target of the system are those which provide the necessary assurances that spent fuel can be received, handled, stored and retrieved without undue risk to health and safety of workers and the public. To achieve these objectives, the design of the system incorporates features to remove spent fuel residual heat, to provide for radiation protection, and to maintain containment over the lifespan of the system as specified in the design specifications. The features also provide for all possible anticipated operational occurrences and design basis events in accordance with the design basis as guided by the designated regulations. The general performance requirements of a projected storage system are introduced in this paper. The storage system is designed to store fuel assemblies in associated with designated regulatory requirements. Small increases/decreases in maximum burnup can be adjusted with cooling time. These variations are compensated for by a corresponding small site-specific increase/decrease in the design basis-cooling period, as long as the maximum heat load and radioactivity of loaded fuel assemblies are met. Generic design basis events considered for the storage system are summarized. Shielding and radiological requirements along with mechanical and structural are derived in this study.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.1
• /
• pp.62-68
• /
• 2001

In order to characterize the microscopic fracture behaviour of the weldment din stress corrosion cracking(SCC) phenomena, SCC and acoustic emission(AE) tests were carried out simultaneously and the correlation between mechanical paramenters obtained from SCC and AE tests was investigated. In the case of base metal, much more AE events were produced at -0.5V than at -0.8V because of the dissolution mechanism before the maximum load. Regardless of the applied voltages to the specimens, however, AE events decreased after the maximum load. In the case of weldment, lots of AE events with larger amplitude $range(40{\sim}100dB)$ were produced because of the singularities of weld HAZ in comparision to the base metal and post-weld heat-treated(PWHT) specimens. Numerous and larger cracks for the weldment were observed on the fractured surfaces by SEM examination. From these results, it was concluded that SCC for the weldment appeared most severely in synthetic seawater. Weld HAZ was softened by PWHT which also contributed to the reduced susceptibility to corrosive environment in comparison to the weldment.