• Fire Science and Engineering
• /
• v.30 no.3
• /
• pp.1-6
• /
• 2016

More than five thousands transportation fires occurannually in Korea and the resulting destruction of property and loss of life is huge and results in traffic and environmental pollution. The recent development of automobile technology such as the hybrid concept and use of bio fuels makes fire protection even more difficult due to a lack of understanding of the new adapted system including vehicle engines. In this study, a numerical simulation was performed on a PSR (perfectly Stirred Reactor) to simulate an automobile engine and to clarify the effect of gasoline/ethanol surrogates as a fuel. The temperature, NOx and soot emissions were predicted to decrease with increasing ethanol content, but that of unburned hydrocarbons was found to increase dramatically. The result will provide not only the basic thermal characteristics for engines and their after-treatment systems, but also make it possible to assess the potential for fire events in these systems when an ethanol mixed fuel is used in gasoline vehicles.

• Journal of Sensor Science and Technology
• /
• v.8 no.4
• /
• pp.327-332
• /
• 1999

Catalytic combustion type gas sensors were fabricated by using noble metal(Pt and Pd) added ${\gamma}-Al_2O_3$ powder with specific surface area of $200\;m^2/g$. The fabricated sensor showed power consumption of 500 mW at the operating voltage of 1.75 V and high sensitivity of about 120 mV for butane, methane, or propane 100%LEL, respectively. The sensor properties also showed good linearity to hydrocarbon gas concentration variation, reproductivity and stability for relative humidity variation. And it showed high stability in butane ambient for 100 days.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.6
• /
• pp.31-37
• /
• 2010

In this study, optimization of MEK and Toluene removal was conducted by HTO(Hybrid Thermal Oxidation) system. HTO system has a multi-bed reaction plate and the plate consisted of wasted heat regeneration part and catalysis part. VOCs removal by HTO system was estimated by changing inlet flow rates with different valve changing times. Under $350^{\circ}C$ of combustion temperature, VOCs was fully converted and the equivalent conversion was 100%. The thermal oxidation efficiency, related to the amount of injected fuel into HTO system and the valve change time, was revealed at the level of 93.0~96.3%. In case of MEK removal by HTO system, the efficiency was ranged from 91.1 to 97.1%. Also, Toluene removal efficiency(93.2~97.4%) was good and stable with respect to the operating conditions. Considering above results, it was proved that HTO system could be a stable and compact system for VOCs, especially MEK and Toluene with high removal efficiency.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.90-96
• /
• 2005

The improvement of combustion stability is very important because it is closely related to the exhaust emission concentrations as well as the fuel consumption during the cold start of SI engine. In our previous studies, the spark and exhaust valve timings were retarded individually from the baseline case to increase the exhaust gas temperature far fast warmup of a close-coupled catalyst. In the study, it was found that combustion stability during cold start becomes worse when the valve timing is retarded from the baseline conditions. The spark and valve timings were simultaneously changed from the baseline conditions to find out the variation of combustion stability during cold start of an Sl engine. Through the study. retarded spark timing by $5^{\circ}$ CA helps improvement of $COV_{imep}$ by $2\%$ and $15^{\circ}C$ increase of exhaust temperature. Retarded exhaust valve timing makes the exhaust gas temperature increase by $30^{\circ}C$, but it also deteriorates the $COV_{imep}$ by $1\%$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.106.2-106.2
• /
• 2010

동식물성 기름과 메탄올의 전이에스테르화 반응에 의해 생산되는 바이오디젤은 환경친화성과 지속가능성이 인정됨에 따라 그 생산량이 급격히 증가하고 있어 대두유, 유채유, 팜유 등의 원료유 부족과 가격 상승, 수급 불안정 등의 문제가 대두되고 있다. 이를 해결하기 위한 방안으로 유리지방산 함량이 높은 저가유지 자원(폐식용유, 폐돈지, 폐우지, soapstock, trapped grease)과 새로운 오일 작물을 이용한 생산 기술 연구가 활발히 진행되고 있다. 본 연구에서는 비활용 해외 열대작물 씨앗에서 착유한 식물성 오일을 정제하여 바이오디젤 원료유를 생산하는 과정에서 발생하는 폐기물(폐유, 폐수)의 경제적 처리 방안으로 유화유 제조 원료(벙커C유, 물)와 유화유 제조 첨가제(무기계, 유기계)로 활용 가능성을 검토하였다. 열대작물 오일의 물성 분석 결과 고형물, 수분, 인지질(phospholipid), 유리지방산(free fatty acid) 함량이 기존 원료유보다 매우 높게 나타났다. 인지질은 바이오디젤 제조 반응후 에스테르와 글리세린의 층분리를 방해하고 유리지방산은 염기촉매와 결합하여 지방산염을 생성해 생산 수율을 감소시킨다. 고형물과 수분 역시 촉매반응에 악영향을 가지나 여과와 감압증발에 의해 쉽게 제거가 가능하다. 유리지방산은 산촉매 에스테르화 반응에 의해 제거가 가능하다. 인지질은 탈검(degumming) 과정을 통해 제거하며 탈검은 수용성 탈검, 산 탈검, 세정 공정으로 구성된다. 착유한 원료유의 고형물을 제거 후 물과 수세하여 수용성 인지질을 수화하여 층 분리해 제거하고 상층의 오일은 추가적인 산 탈검을 수행한다. 그 뒤 세정을 통해 사용된 탈검제인 산과 추가적으로 수화된 인지질을 제거하게 된다. 이러한 3단계의 탈검 과정에서 하층으로 오일과 물이 폐기물로서 배출되며 본 연구에서는 배출 폐기물을 다시 층분리하여 오일층과 물 층으로 구분하여 유화유 제조에 사용되는 벙커C유, 물, 그리고 기존 유기계 및 무기계 유화제의 대체 가능성을 조사하였다. 유화 연료유는 기름과 물을 균일한 분산상으로 혼합한 연료유로 연소시 오일계 성분의 미연분을 감소시켜 연료 효율 제고와 배출가스 성상을 개선하기 위해 개발되어 왔다. 본 발표에서는 다양한 종류의 상용 첨가제 및 바이오디젤 원료유 생산 폐기물을 활용해 유화 연료유를 제조하였으며 각 유화유의 장시간의 상(phase) 안정성을 비교하였다. 바이오 폐기물 중에는 천연 계면활성제(surfactant)인 인지질이 다량 함유되어 있어 기존의 무기계 및 유기계 유화제보다 상 안정성이 우수하게 나타났으며 바이오디젤 원료유 생산 공정의 폐기물인 폐유과 폐수의 활용이 가능한 것으로 나타났다.

• Journal of Hydrogen and New Energy
• /
• v.28 no.1
• /
• pp.1-8
• /
• 2017

Cu/Mn/Ce catalysts for water gas shift (WGS) reaction were synthesized by urea-nitrate combustion method with the fixed molar ratio of Cu/Mn as 1:4 and 1:1 with the doping concentration of Ce from 0.3 to 0.8 mol%. The prepared catalysts were characterized with SEM, BET, XRD, XPS, $H_2$-TPR, $CO_2$ TPD, $N_2O$ chemisorption analysis. The catalytic activity tests were carried out at a GHSV of $28,000h^{-1}$ and a temperature range of 200 to $400^{\circ}C$. The Cu/Mn(CM) catalysts formed Cu-Mn mixed oxide of spinel structure ($Cu_{1.5}Mn_{1.5}O_4$) and manganese oxides ($MnO_x$). However, when a small amount of Ce was doped, the growth of $Cu_{1.5}Mn_{1.5}O_4$ was inhibited and the degree of Cu dispersion were increased. Also, the doping of Ce on the CM catalyst reduced the reduction temperature and the base site to induce the active site of the catalyst to be exposed on the catalyst surface. From the XPS analysis, it was confirmed that maintaining the oxidation state of Cu appropriately was a main factor in the WGS reaction. Consequently, Ce as support and dopant in the water gas shift reaction catalysts exhibited the enhanced catalytic activities on CM catalysts. We found that proper amount of Ce by preparing catalysts with different Cu/Mn ratios.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.299-304
• /
• 2013

The HAN which is an ionic liquid is a non-toxic monopropellant with high storability, and its specific impulse can be increased by blending methanol, thereby it can substitute the hydrazine. The HAN was synthesized by acid-base reaction of hydroxylamine and nitric acid, and the blending ratio of HAN and methanol is 8.2:1. The iridium catalyst was used to decompose the HAN, and 1 N class thruster with shower head type injector having one orifice was used to evaluate the HAN/Methanol propellant. The thermal stability of distributor was increased by using ceramic material to endure the high temperature of product gas. The preheating temperature of catalyst should be $400^{\circ}C$ at least for the complete decomposition. The feeding pressure should be increased to increase the $C^*$ efficiency, thereby the decomposition performance was decreased upstream catalyst, and the performance of thruster was decreased. The fine metal mesh was inserted after the injector to improve the atomization of propellant, thereby it can settle the performance decrease problem. The phenomenon of performance decrease was remarkably improved owing to the insertion of fine metal mesh.

• Journal of Environmental Science International
• /
• v.13 no.7
• /
• pp.619-626
• /
• 2004

We have studied the catalytic combustion of soot particulates over perovskite-type oxides prepared by malic acid method, The catalysts were modified to enhance the activity by substitution of metal into A or B site of perovskite oxide. In addition, the reaction conditions such as temperature and $O_2$ concentration were investigated. The partial substitution of alkali metals into A site in the $LaMnO_3$ catalyst, enhanced the catalytic activity in the combustion of carbon particulate and the activity was shown in the order: Cs > K > Na. For the $La_{1-x}Cs_{x}MnO_{3}$ catalysts, the catalytic activity showed the maximum value with x=0.3 but no more increase on the catalytic activity was shown with x > 0.3. For the $La_{0.8}Cs_{0.2}MnO_{3}$ catalyst, the substitution of Fe or Ni increased the ignition temperature. The ignition temperature decreased with an increase of $O_2$ concentration, however, no more increase in the catalytic activity was shown with $O_2$ concentration > 0.2. The introduction of NO into reactants showed no effect on the catalytic activity.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.3
• /
• pp.371-379
• /
• 2013

In order to improve the selective oxidation reaction of gaseous ammonia at a low temperature, various types of metal-impregnated activated alumina were prepared, and also physical and chemical properties of the conversion of ammonia were determined. Both types of metal (Cu, Ag) impregnated activated alumina show high conversion rate of ammonia at high temperature (over $300^{\circ}C$). However, at lower temperature ($200^{\circ}C$), Ag-impregnated catalyst shows the highest conversion rate (93%). In addition, the effects of lattice oxygen of the developed catalyst was studied. Ce-impregnated catalyst showed higher conversion rate than commercial alumina, but also showed lower conversion rate than Ag-impregnated sample. Moreover, 5 vol.% of Ag activation under hydrogen shows the highest conversion rate result. Finally, through high conversion at low temperature, it was considered that the production of NO and $NO_2$, toxic by-products, were effectively inhibited.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.91.1-91.1
• /
• 2011

고체산화물 연료전지(Solid Oxide Fuel Cell이하 SOFC)는 연료가 갖는 화학에너지를 연소과정 없이, 공기와 H2, CO, CH4와 같은 환원성 가스를 공급받아 $600{\sim}1000^{\circ}C$에서 전기화학적 반응을 통하여 직접 전기를 얻는 방식이다. SOFC는 $700^{\circ}C$ 이상의 고온에서 고체산화물이 연료와 공기가 반응하여 전기와 열을 동시에 생산하기 때문에 carnot cycle의 제한을 받지 않아 발전효율이 40% 이상으로 고효율이고, NOx 및 SOx를 배출하지 않아 무공해이며, moving parts가 없어 소음이 나지 않고, 건설과 증설이 지역이나 기후 조건에 제약 없이 용이하고, 다양한 용량이 가능하며, 고가의 백금 촉매를 사용하지 않으며, 수소, 석탄가스, 천연가스 등의 연료를 사용할 수 있는 장점이 있음, 또한 다향한 형태로 제작할 수 있으며 전해질이 고체에서 전해질 손실 및 보충에 문제가 없고 타 연료전지에 비해 개질기가 필요 없어 발전시스템이 간단하고 경량화가 가능하다. 전사법은 paste를 제작하여 전사용지에 Screen printing하여 건조 후 coating하는 방법으로 기존의 여러 coating 방법보다 제작이 용이하고 소재의 크기, 두께조절이 간편하며, 구성층의 표면조도나 굴곡에 대응이 용이한 방법이다. 본 실험에서는 paste 제조, 전사법을 이용하여 Anode, AFL, Electrolyte, CFL, Cathode전사지를 제작하고 이를 세라믹 평관형 지지체에 변수로 두께 조건별 Coating 한 후 $1400^{\circ}C$ 소결을 진행하여 SEM 분석으로 미세구조 관찰, 출력특성 및 Impedance을 확인하였다.