• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.642-648
• /
• 2011

This paper describes an experimental study on ultrasonic welding of similar and dissimilar metals. There are optimum welding conditions which are found for welding of Al/Al and Al/Cu. It evaluated weldability using tensile test, SEM observation and EDX-ray analysis. Both ultrasonic welding of Al/Al and Al/Cu have amplitude as the variable factor. Al/Cu welding was examined again with welding time as variable factor to find the best conditions. The more welding time or amplitude increase, the better weldability. The optimum conditions for ultrasonic welding of Al/Al were formed at pressure 0.25 MPa, welding time 0.25 sec, amplitude 90%. Pressure 0.25 MPa, welding time 0.4 sec, amplitude 80% are optimized for Al/Cu ultrasonic metal welding and solid-state diffusion generated by ultrasonic vibration and frictional heat is confirmed at the welded interface.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.70-75
• /
• 2012

The technique with ultrasonic vibration refers to the many industries. Especially Ultrasonic Connection Method is widely used for mobile battery, secondary battery, automobile components and also they recently started using it for terminal connecting of solar community battery. In this study, ultrasonic welding horn is analysed and designed with FEM, then manufactured based on it. Resonance frequency and amplitude of horn would be measured and compared with the designing result to judge the suitability. Al/Al specimen is welded by the manufactured horn and verify its performance via the weldability evaluation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.76-81
• /
• 2012

Ultrasonic metal welding is one of the welding methods which welds metal by applying high frequency vibrational energy into specific area at constant pressure, avaliable in room temperature and low temperature. Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper focused to horn design, its length L was set to 62mm by calculating vibration equation. By performing modal analysis with various shape variable b times integer, when length of b is 30mm the output was 39,599Hz at 10th mode. Also by performing harmonic response analysis, the frequency response result was 39,533Hz, which was similar to modal analysis result. In order to observe the designed horn's performance, about 4,000 voltage data was obtained from a light sensor and was analyzed by FFT analysis using Origin Tool. The result RMS amplitude was approximately 8.5${\mu}m$ at 40,000Hz, and maximum amplitude was 12.3${\mu}m$. Therefore, it was verified that the ultrasonic metal welding horn was optimally designed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.55-61
• /
• 2013

The horn is a key part of the ultrasonic welder. As the shape, mass and material of a horn have effects on the resonant frequency and the vibration mode in ultrasonic welding, a horn has to be designed and manufactured accurately. In this study, 40kHz band horn was designed and manufactured through the vibration mode and finite element analysis. A result of modal analysis showed that the natural frequency of the horn was 39,794Hz, and the frequency response by a harmonic response analysis was 39,800Hz - close to the intended frequency, 40kHz. In addition, weldability of the developed horn was estimated by welding of two Ni sheets and tensile-shear test of welded samples. It was shown the developed horn could be used in metal sheet welding.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.195-202
• /
• 2006

High-speed machining (HSM) with excellent quality and dimensional accuracy has been widely used to create 3D structures of metal and plastics. However, the high-speed machining process is not suitable for the rapid realization of 3D thin-walled product because it consumes considerably long time in fixturing process of a work piece. In this paper, an effective rapid manufacturing process is proposed to fabricate 3D thin-walled products directly using HSM, phase change filling and ultrasonic welding. The filling process is useful to hold the thin-walled product during the machining step. The ultrasonic welding process is introduced to make one piece product from two piece parts that are machined by HSM and filling process. The proposed rapid manufacturing (RM) process has been shown that the RM process enables to fabricate the 3D thin-walled products using ABS plastics and aluminum metals from 3D CAD data to functional parts.