• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.4
• /
• pp.715-725
• /
• 2002

In this study, a method to determine the deformed shape of planar cable under vertical loads was presented. To obtain the deformed shape of cable by general cable theorem, a sag at arbitrary point is usually given. However, in general cases without a given sag, the proposed method determines the deformed shape of cable based on the equations of cable theorem and geometric compatibility by iterative way. The method was also extended to slove extensible cable. It was acknowledged from numerical analysis and model tests in laboratory that the proposed method is valid lot analysis of extensible cable as well as unextensible cable.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.5A
• /
• pp.699-707
• /
• 2008

For most structural evaluation of bridge integrity, it is very important to measure the geometric profile, which is a major factor representing the global behavior of civil structures, especially bridges. In the past, because of the lack of appropriate methods to measure the deflection profile of bridges on site, the measurement of deflection has been restricted to just a few discrete points along the bridge, and the measuring points have been limited to the locations installed with displacement transducers. Thus, some methods for predicting the static deflection by using fiber optic strain sensors has been applied to simply supported bridges. In this study, a method of estimating the static deflection profile by using strains measured from suspension bridges was proposed. Based on the classical deflection theory of suspension bridges, an equation of deflection profile was derived and applied to obtain the actual deflection profile on Namhae suspension bridge. Field load tests were carried out to measure strains from FBG strain sensors attached inside the stiffening girder of the bridge. The predicted deflection profiles were compared with both precise surveying data and numerical analysis results. Thus, it is found that the equation of predicting the deflection profiles proposed in this study could be applicable to suspension bridges and the FBG strain sensors could be reliable on acquiring the strain data from bridges on site.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.275-275
• /
• 2017

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.833-839
• /
• 2013

In this study, an experiment was performed to monitor the two-dimensional shape of a cantilever composite structure using fiber Bragg grating (FBG) sensors. To monitor the shape of a composite structure, a deflection equation developed by NASA was applied and a composite beam attached to three FBG sensors was used. In the experiment, the shape of the composite beam was successfully estimated and an error was evaluated by comparing a real deflection. The error increased with real deflection; therefore, it was compensated by using the linear relationship between the error and the real deflection. After compensating the error, the measured deflection shows good agreement with the real deflection. Finally, the experiment shows that the FBG sensor and the deflection equation are suitable for monitoring the deflection curve of the beam structure with compensation of the error.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.119-128
• /
• 1994

Deflection estimation at engine room upper deck panel is performed for the actual ship structure. These deflection behaviours are basically investigated from not only the data based on the full series results of nonlinear analysis using Incremental Galerkin's Method but also actual deflection data measured from damaged ship under construction in dry dock. The effects of residual stress, initial deflection and static loading are also included. The computed estimation results of upper deck plate panel including theme effects are shown that upper deck platings of new ship expected less deflection magnitude than damaged ship.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.355-363
• /
• 2023

In safety assessment of a aged bridge, dynamic characteristics and displacement are directly related to the rigidity of the structural system, especially displacement is the most important factor as the physical quantity that the bridge user can directly detect. However, in order to measure the displacement of the bridge, it is difficult to install displacement sensors at the bottom of the bridge and conduct traffic blocking and loading tests, resulting in increased costs or impossible measurements depending on the bridge's environment. In this study, a method of measuring the displacement of a bridge using only accelerometers without installing displacement sensors and ambient vibration without a loading test was proposed. For the analysis of bridge dynamic characteristics and displacement using ambient vibration, the mode shape and natural frequency of the bridge were extracted using a TDD technique known to enable quick analysis with simple calculations, and the unit load displacement of the bridge was analyzed through flexibility analysis to calculate static displacement. To verify this proposed technology, an on-site test was conducted on C Bridge, and the results were compared with the measured values of the loading test and the structural analysis data. As a result, it was confirmed that the mode shape and natural frequency were 0.42 to 1.13 % error ratio, and the maximum displacement at the main span was 3.58 % error ratio. Therefore, the proposed technology can be used as a basis data for indirectly determine the safety of the bridge by comparing the amount of displacement compared to the design and analysis values by estimating the displacement of the bridge that could not be measured due to the difficulty of installing displacement sensors.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.460-465
• /
• 2016

Long pipe structures are usually installed in fixtures located with regular intervals or laid underground. Therefore, deflection and deformation could easily occur due to their weight or ground activity. A shape monitoring technique can be used effectively to evaluate the integrity of the pipe structures. Fiber Bragg grating (FBG) sensors, which have an advantage of multiplexing could be used to measure strains at multiple-points of a long structure. In this study, to evaluate the integrity of a pipeline, a shape estimation technique based on strain information was proposed. Furthermore, different experiments were conducted to verify the performance of the proposed technique. Thus, the proposed shape estimation technique can represent the shape according to the deformation of the specimen using the FBGs. Moreover, calculated deflection of the pipeline using the estimation technique showed a good agreement with the actual deflection of the pipeline.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.473-476
• /
• 2011

본 논문에서는 열차와 교량의 상호작용과 주행속도에 의해 결정되어지는 진동지속시간과 차체연직가속도 증폭효과를 고려하여 철도교량의 진동사용성 허용처짐을 제시하고자 하였다. 열차가 교량을 통과할 때의 처짐 형상을 사인파로 가정하고 열차와 교량의 상호작용을 진동전달함수로 표현하여 철도교량의 진동 사용성 허용처짐을 유도하였다. 그리고 진동지속시간을 고려하기 위해 연직가속도 허용기준으로서 진동지속시간을 고려한 교량구조물의 진동사용성기준을 사용하였다. 매개변수연구를 통하여 열차 주행속도의 증가에 비례하여 차체연직가속도는 증가하지만 교량최대변위의 변화는 미미함이 확인됨으로 인하여 차체연직가속도 증가와 동반하여 연직가속도 허용기준역시 증가하는 것을 보정할 필요가 있을 것으로 판단하였다. 따라서 전개된 철도교량의 진동사용성 허용처짐식에 매개변수연구를 통하여 가정한 가속도 증폭계수를 적용하여 열차의 증속에 의한 가속도증폭효과를 고려하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.258-261
• /
• 1998

2차원 시스템과는 달리 3차원 의복 CAD 시스템을 이용하면, 직접 재단 봉제 과정을 거치지 않고도, 만들어진 의복의 형상과 착장 상태를 확인해볼 수 있다는 장점이 있다. 이러한 3차원 시스템에서는 의복의 자연스런 처짐, 이른바 드레이프(drape)를 잘 표현하여야만 실제에 최대한 가까운 의복의 형상을 보여줄 수 있다.(중략)

• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.93-103
• /
• 2009

The concept of the effective moment of inertia has been generally used for the deflection estimation of reinforced concrete flexural members. The KCI design code adopted Branson's equation for simple calculation of deflection, in which a representative value of the effective moment of inertia is used for the whole length of a member. However, the code equation for the effective moment of inertia was formulated based on the results of beam tests subjected to uniformly distributed loads, which may not effectively account for those of members under different loading conditions. Therefore, this study aimed to verify the influences of moment shapes resulting from different loading patterns by experiments. Six beams were fabricated and tested in this study, where primary variables were concrete compressive strengths and loading distances from supports, and test results were compared to the code equation and other existing approaches. A method utilizing variational analysis for the deflection estimation has been also proposed, which accounts for the influences of moment shapes to the effective moment of inertia. The test results indicated that the effective moment of inertia was somewhat influenced by the moment shape, and that this influence of moment shape to the effective moment of inertia was not captured by the code equation. Compared to the code equation, the proposed method had smaller variation in the ratios of the test results to the estimated values of beam deflections. Therefore, the proposed method is considered to be a good approach to take into account the influence of moment shape for the estimation of beam deflection, however, the differences between test results and estimated deflections show that more researches are still required to improve its accuracy by modifying the shape function of deflection.