• Fire Science and Engineering
• /
• v.28 no.6
• /
• pp.28-34
• /
• 2014

Two kinds of new piperazinomethyl-bis-phosphonic acid $M^{n+}$ ($PIPEABPM^{n+}$) were synthesized and their combustive properties of Pinus rigida plates treated with $PIPEABPM^{n+}$ were tested in comparison with the previously synthesized chemicals. Pinus rigida specimens were painted in three times with 15 wt% $PIPEABPM^{n+}$ solutions at the room temperature. After drying specimen treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). As a result, the combustion-retardation properties were partially increased by due to the treated $PIPEABPM^{n+}$ solutions in the virgin Pinus rigida. Especially, the specimens treated with $PIPEABPM^{n+}$ showed both the lower peak heat release rate ($HRR_{peak}$) (173.48~145.36) s and total heat release rate (THRR) (73.0~55.2) $MJ/m^2$ than those of virgin piperazinomethyl-bis-phosphonic acid (PIPEABP)-plate. Compared with virgin PIPEABP-plate, the specimens treated with the $PIPEABPM^{n+}$ showed low combustive properties. However the specimens treated with $PIPEABPM^{n+}$ showed both the shorter time to ignition (TTI) (58~18) s and the time to flameout (Tf) (564~456) s than those of virgin PIPEABP-plate by increasing the thermal conductivity.

• Fire Science and Engineering
• /
• v.27 no.5
• /
• pp.57-63
• /
• 2013

This study was performed to test the combustive properties of Pinus rigida plates treated with piperazinomethyl-bisphosphonic acid (PIPEABP), methylpiperazinomethyl-bis-phosphonic acid (MPIPEABP), and N,N-dimethylethylenediaminomethyl- bis-phosphonic acid (MDEDAP). Pinus rigida specimens were painted in three times with 15 wt% alkylenediaminoalkyl- bis-phosphonic acid solutions at the room temperature. After drying specimen treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). As a result, the combustion-retardation properties were increased by due to the treated alkylenediaminoalkyl-bis-phosphonic acid solutios in the virgin Pinus rigida. Especially, the specimens treated with chemicals showed both the later time to ignition (TTI) (148-116 s) and longer time to flameout (Tf) (633-529 s) than those of virgin plate by reducing the burnig rate. Compared with virgin pinus rigida plate, the specimens treated with the alkylenediaminoalkyl-bis-phosphonic acids showed partially low combustive properties. However the specimens treated with PIPEABP showed both the higher peak heat release rate (PHRR) (187.56 $kW/m^2$) and higher total heat release rate (THRR) (75.7 $MJ/m^2$) than those of virgin plate.

• The Korean Journal of Nuclear Medicine
• /
• v.30 no.4
• /
• pp.541-547
• /
• 1996

The previous monoclonal antibody labeling method for bone marrow immunoscintigrapy was complicated and laborious for clinical application. Also it showed a relatively low labeling efficiency. To improve this procedure, we compared several direct labeling methods of $^{99m}Tc$. 1) The labeling efficiency in the method using gluconate as a transchelator was low (40-70%), but immunoscintigraphy using this radiotracer produced a clear image. 2) To improve labeling efficiency, ${\beta}$-mercaptoethanol was removed after reduction. The labeling efficiency was improved up to 70-80%, but the radioactivity of the blood pool was high. 3) The higest labeling efficiency (>90%) and best quality images could be obtained by using MDP as a transchelating agent. It did not require additional procedures for separation of labeled antibodies. The immunoreactivity of this antibody was 60%. Residual MDP which can be taken up by the bone could be removed by PD-10 column. The reduced antibodies were stable with a high labeling efficiency (>90%) for up to 47 days by deep freezing. We concluded that the improved procedure for $^{99m}Tc$ labeling of anti-NCA-95 monoclonal antibody using MDP as a transchelating agent will be a simple and useful method for clinical application.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1222-1233
• /
• 1990

The formation and oxidation processes of soot particles in a diesel flame were investigated with a rapid compression machine. A cloud of soot particles was successfully visualized by means of the instantaneous laser shadow photographs technique and the equivalence ratio of the soot formation zone was estimated from a measured fuel concentration distribution in a nonevaporating spray. The temporal and spatial variation of soot concentration in the flame was also correlated with the rate of heat release. Soot particles appears first in a region near the flame tip when diffusion combustion period starts, and its concentration is a maximum at about the end of injection, then decreases due to oxidation. The reason for soot being formed in a fuel lean region near the flame tip is the evaporated fuel requires time to be pyrolized as it travels through the burning fuel rich zone towards the flame tip.

• Plant Journal
• /
• v.11 no.3
• /
• pp.46-52
• /
• 2015

200MWe 순환유동층보일러인 A화력발전소는 정부정책에 의해 국내 무연탄만을 연료로 배정받아 운영되었다. 하지만 무연탄에 대한 민간수요 증가에 따른 정부의 정책변경에 따라 유 무연탄 혼탄을 2000년대 후반부터 시행하고 있다. 하지만 기동시 석탄 투입온도는 여전히 무연탄 전소시의 기준온도인 $600^{\circ}C$에 석탄을 투입하고 있는 실정이라 기동시간 지연의 한 원인으로 작용하고 있고 기동 중 소요되는 경유의 과다소비라는 고질적인 문제점을 안고 있다. 이에 본 연구에서는 A화력에서 사용되는 석탄에 대한 공업분석과 원소분석을 통하여 비교적 휘발분이 많고 반응성이 좋은 러시아산 유연탄(Suek) 연소에 따른 경유에서 석탄으로의 연료교체시 경제적인 시점을 예측하였다. 실험결과 러시아산 유연탄 (Suek) 연소시 투입가능온도는 연소전환율이 90%이상이 되는 연소최대온도($426^{\circ}C$)가 기술적, 경제적으로 가장 적합한 것으로 예상하였다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.29 no.1
• /
• pp.30-38
• /
• 1993

In this study, the combustion characteristics in a pre-combustion chamber diesel engine was investigated with experimental conditions of marine engine load. The heat release analysis used was a single-zone single-chamber thermodynamic analysis based on pre-combustion chamber pressure-time data. Based on the results of this investigation, the following conclusions were reached: 1) Increasing the load, peak pressure was increased and position of P sub(max) was retarded in crank angle degrees. 2) Ignition delay time was almost constant without relating to the load and the heat values to form a combusitible mixture were decreased apparently with increasing the load. 3) In premixed-combustion mode, the pattern of heat release rate was resembled without relating to the load and premixed-combustion time was shortened with increasing the load. 4) Increasing the load, mass of premixed-burned fuel was increased slightly, but was invariable beyond a certain fuel-air ratio. 5) Increasing the load, premixed-burned fraction was decreased.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.73-80
• /
• 2015

In this study, the conditions of explosion range of gasoline, which is used as combustion improver, are experimentally analyzed. Two types of compartment, which is the small scale ($0.5m{\times}0.5m{\times}1.0m$) and the middle scale ($0.5m{\times}0.5m{\times}1.0m$), are mocked-up and the auto-control systems are installed in order to measure the vaporized gasoline and the moment of pressure, ignition time and maximum pressure. In case the maximum flammable limit of gasoline is up to 22.4 Vol% not the generalized range of 1.4~7.6 Vol% when nichrome igniter of $700^{\circ}C$ is used. These results can be appled to the analytical prediction of fire identification in the field of explosion.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.3
• /
• pp.547-556
• /
• 2000

A study have been conducted for the adsorption and desorption characteristics of Cu ion using manganese nodule as adsorbent. For 100 ppm Cu ion solution, the adsorbed amount of Cu ion was more than 90 % at equilibrium state. Adsorption was equilibrated in 42 hours the adsorption reaction was shown to be first order reaction. For the desorption reaction of Cu ion in the region of solution pH 3.5~9.5, the desorption was completed in the acidic region, but it has been decreased as the pH was raised. Also, the desorption rate was higher in the acidic region compared with alkaline region. The desorbed amount was decreased as the reaction temperature increased, therefore, the desorption reaction was thought to be exothermic. Also, several thermodynamic properties were calculated based on experimental results and compared with theoretically driven values. To see the effect of complexing agent on the desorption of Cu ion, EDTA was introduced and the des orbed amount increased in the presence of EDTA.

• Journal of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.151-157
• /
• 1991

A sensitive stripping voltammetric study of the complex of indium with 8-hydroxyquinoline at a hanging mercury drop electrode was investigated in 0.1M acetate buffer solution. The effects of various analytical conditions on the reduction peak current of the adsorbed complex were discussed. Optimal analytical conditions were found to be the ligand concentration of $2 {\times}10^{-5}$M, solution pH 4.75, scan rate of 10 mV/s, deposition potential of -0.450V, a deposition time of 90 second. Interferences by other trace metals and Triton X-100 were also discussed. Detection limit was 0.2 ppb of indium after 90 sec. Deposition time, and the relative standard deviation(n = 10) at 4 ppb was 3.2%.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.897-900
• /
• 2008

Some substances of cement could make underestimate concentration of hexavalent chromium(Cr(VI)) as they reduce Cr(VI) to Cr(III) in acidic condition during the determination of Cr(VI) content in cement. The reduction of Cr(VI) increased with elapsed time after acidification in this study. The reduction rate varied with various cements. From our result, we can conclude that simultaneous additions of acid and DPC were required for the accurate measurement of Cr(VI) in cement. The high recovery rate of 94.3 to 106.7% with the simultaneous acid-DPC addition method can also support our conclusion.