• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.19-21
• /
• 2003

일반적으로 PMDC모터에 사용되는 자석은 가격과 재질에 따라서 여러 가지로 분류할 수 있다. 그러나 착자방법에는 등방향과 방사형 착자로 나눌 수 있고 용도에 따라서 다극으로 착자할 수 있다. 하지만 그 기본적인 구조에는 원통형, 판형, 육면체형으로 분류할 수 있는데 구형, 반구형 또는 구형 shell에 관한한 아직까지 소개된 문헌이 빈약하다. 본 논문에서는 슬롯리스 구형직류모터에 사용될 반구형 shell형태의 영구자석의 착자기 구조와 착자방법에 대한 가능성을 찾아보고 이론적으로 증명하고자 한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.3
• /
• pp.197-203
• /
• 2009

This paper presents a novel method to diagnose magnetization faults produced during magnetization process using stator coils of a brushless dc motor with concentrated windings. It is demonstrated that the stator coil magnetization faults can cause a drop of energy efficiency of the brushless dc motor through computer simulations using a magnetization fault model and efficiency test using compressors. The proposed method diagnoses the stator coil magnetization faults by using an inverter during the brushless dc motor driving test after the magnetization process is completed. An experimental study on the brushless dc motor for compressor shows that the stator coil magnetization faults can be detected with high sensitivity.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1004-1006
• /
• 2004

MFL PIG는 빠른 속도로 주행하면서 MFL 신호를 측정하여 기록하게 된다. PIG가 주행함에 따라 MFL 신호를 왜곡시키는데 가스관에 인가되는 강한 자기장으로 인하여 가스관이 착자되어 왜곡이 발생한다. 가스관의 착자는 종방향 착자와 횡방향 착자로 나눌수 있으며, 횡방향 착자는 검출신호를 증가시키거나 감소시키는 방향으로 왜곡을 발생시키고, 종방향 착자는 인가돼는 자기장과 수직이 되므로 검출신호를 크게 왜곡시킨다. 따라서 검출신호를 보정하여 실제 결함에 의한 신호를 검출하여야 한다. 본 연구에서는 가스관의 착자에 의한 영향을 분석하고 신호보정에 관하여 연구하였다.

• Journal of the Korean Magnetics Society
• /
• v.2 no.2
• /
• pp.145-149
• /
• 1992

The characteristics of electromagnetic devices with permanent magnet depends greatly on the remanence pattern of permanent magnet. So, it is necessary to analyze the pattern of remanence in permanent magnet. This paper presents a finite element analysis of magnetizer considering the nonlinearity and anisotropy of yoke and magnet in magnetizer. The distributions of magnetizations are obtained according to the variations of magnetizing currents for two kinds of magnetizers with different magnetizing poles. It is found that the excessive magnetizing current results in the reduction and polarity reversion of magnetization in the multi-pole magnetizing system where the pole angle is too small. During the design and analyzing of multi-pole magnetizer, it must be considered that there exists an optimal value of magnetizing current and pole angle of magnetizer.

• Journal of Korea Society of Industrial Information Systems
• /
• v.28 no.2
• /
• pp.21-30
• /
• 2023

As the adoption and high-performance enhancement of Electric Vehicles continue, the demand for high-output motors and high-capacity Magnetizer for producing large-scale IPMSM is increasing. The maximum peak current of the magnetization and the capacitor discharge time, which are important factors in the magnetization process, are determined by the circuit constants of the magnetizer. In this paper, we analyze the magnetizing system using MATLAB SIMULINK to design the circuit constant of the magnetizing yoke for magnetizing design and present the design procedure for Design the circuit constant. As a result, the parameters of the magnetizing yoke were derived to be 0.015[ohm] and 0.035[mH] based on the capacitance of 15,000[uF] and voltage of 5,000[V].

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.4
• /
• pp.1014-1025
• /
• 1996

The magnetizer that is magnetizing the magnet which is used for RGB (Red Green Blue) control of CRT(Cath-ode-Ray Tube)and the magnet inspection unit which is used for test the state of magnetizing have been imported by magnet manufactures up to now. They are operation by manual now, so that they are needed lots of time and have an increase in probability of malefunction by operator. In this study, we have developed a united system from the magnet production process to inspection ork to automaized a entire progress. Therefor, as we are testing the status of every work and analyzing exactly the distribution in quality with this system, we have known that the reliability of magnetization and magnetized status test has not only increased, but the rate of inferior quality almost not generated.

• The Journal of the Korean dental association
• /
• v.17 no.12 s.127
• /
• pp.895-899
• /
• 1979

치석다침착자의 치석의 화학성분함량을 구명하기 위하여 치태제거후 6개월에 치태침착도가 심한 사람과 경한 사람을 분류하여 전악으로부터 치태를 채취하였다. 그리고 채취된 치태 세포성분획과 비세포성 부분으로 분리하여 각 분획에서 탄수화물, 단백질, 지질, Ca, Mg, K 및 P의 함량을 화학적으로 분석측정한 결과는 다음과 같다. 1. 치석다침착자의 치태 건조중량당 10%의 탄수화물, 43%의 단백질, 18%의 지질, 4.3%의 Ca, 0.15%의 Mg, 0.29%의 K과 2.87%의 P으로 구성되어 있다. 2. 탄수화물, 지질, K은 비세포 성분획에서 단백질, Mg, 세포성분획에서 많이 차지하였다. 3. Ca, Mg, P의 함량은 치석다침착자의 치태에서 K의 함량은 치석경침착자의 치태에서 높았다. 4. Ca/P비는 비세포성분획보다 세포성 분획에서 훨씬 낮았다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.860-861
• /
• 2015

본 논문에서는 대용량 착자요크의 설계과정에서 최대입력 전류의 크기를 산정하기 위하여 해석적인 방법을 이용하여 산정하였다. 착자요크의 등가회로로부터 회로방정식을 도출하고 2차 미분방정식으로 표현하여 입력전류를 산정하였다. 산정된 입력전류는 회로해석 툴 및 유한요소해석을 이용한 상용소프트웨어와 비교하여 해석방법의 타당성을 검증하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.4
• /
• pp.415-421
• /
• 2015

This paper describes the study of the design procedure for the step-by-step setup parameters and of the magnetizing method for performance and size reduction in the development of a haptic vibrator. The study of magnetization was accomplished by comparing the electromagnetic force in accordance with the horizontal and the vertical magnetization. The theoretical results indicated that the horizontal magnetization resulted in a better performance. The systematic design of a step-by-step procedure for establishing the design parameters was verified by testing the characteristics of the fabricated prototype product. The vibration response function analysis and electric field analysis were processed by decoupling of the analytical method, and these were determined to be in good agreement with the test results. The design parameters to contributing to the product reliability included the spring height, the welding position, and the coil position. The sensitivity of the electromagnetic field and the performance change were analyzed based on the design parameters. As a result, we proposed a design method to implement a reliability-based, high performance haptic vibrator.

• 전기의세계
• /
• v.51 no.6
• /
• pp.28-34
• /
• 2002