• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.455-464
• /
• 2019

The sensorless control based on the flux linkage of PM synchronous motors has excellent position estimation characteristics at low speeds. However, a limitation arises because the integrator of flux estimator is saturated by the DC offset generated during the analog to digital conversion(ADC) process of the measured current. In order to overcome this limitation, HPF with a low cutoff frequency is used. However, the estimation performance is deteriorated (Ed- the verb deteriorate already includes the meaning of 'problem') at high speed due to the low cutoff frequency, and increasing the cutoff frequency of the HPF induces further problems of phase leading and initial starting failure at low speeds. In this paper, the cutoff frequency of HPF was synchronized to the operation frequency of the motor: at low speeds the cutoff frequency was set to low in order to reduce the phase leading of the estimated flux, and at high speeds it was set to high to raise the DC offset removal performance. As a result, the operating range was increased by 200%. Furthermore, a phase compensation algorithm is proposed to reduce the phase leading of the HPF to less than 1.5 degrees over the full operating range. The proposed sensorless control algorithm was verified by experiment with a PM synchronous motor for a washing machine.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 1997.11a
• /
• pp.211-220
• /
• 1997

체비셰프 삽입손실법을 이용하여 선택도가 높은 대역 여파기를 설계한다. 체비셰프 방식은 차단주파수 근방 곡선의 경사가 버터워쓰에 비해 급격하게 떨어지는 특징을 가진다. 인접 채널의 간섭을 최소화 하기위해 차단 대역의 감쇄를 70db이상으로 유지한다. 중심주파수는 885MHz에서 통과대역폭 10MHz의 여파기를 제작하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4C
• /
• pp.377-385
• /
• 2010

In this paper, a general and explicit technique is presented for determining the filter coefficients of maximally flat (MAXFLAT) FIR filter with the magnitude response exactly passing through a prescribed cutoff point. This technique is based on a general formula (i.e. impulse response) with an arbitrary cutoff point and permits direct computation of the coefficients of this filter type with a specified cutoff point. The technique provides an explicit method for choosing the order of flatness of the filter with the specified cutoff point. Also, in the paper, it is shown to give a computationally efficient and accurate solution to the design of the filters with the desired cutoff point.

• Journal of IKEEE
• /
• v.27 no.1
• /
• pp.71-77
• /
• 2023

In this paper, a dual-band stopband frequency selective surface that can be applied to Wi-Fi 6E systems is designed to block external interfering signals with adjacent operating frequency spectrum in indoor wireless LAN environments. The proposed frequency selective surface structure has frequency blocking characteristics in the 2.4GHz and 6GHz bands, and is realized through a modified crossed dipole structure and an interlocking puzzle form between unit structures. The proposed structure is designed to have stable frequency response characteristics with respect to incident angle and polarization, and the experimental results show good agreement with the simulation results for incident waves from 0° to 45°.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1998.06e
• /
• pp.7-10
• /
• 1998

일반적으로 매우 낮은 차단주파수를 가지는 FIR 저역통과 필터의 경우 그 과도영역의 폭이 상대적으로 매우 좁기 때문에 긴 임펄스 응답을 가지게 되며, 따라서 많은 계산량을 필요로 하게 된다. 본 논문에서는, FIR 필터의 계수를 서브샘플링(subsampling)하여 계산량의 현저한 감소를 도모하고, 그로 인하여 발생하는 주파수 영역의 이미지를 IIR 필터를 사용하여 제거하는 기법을 제안한다. IIR 필터로 인하여 발생하는 위상의 왜곡은 앞단의 FIR 필터의 계수를 조절함으로써 상쇄시킬 수 있다. 제안된 알고리듬을 채택할 경우, 동일한 성능의 일반 FIR 필터에 비하여 사용하는 메모리의 양은 거의 같으나, 계산량은 수십분의 일까지 감소시킬 수 있다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.4
• /
• pp.23-29
• /
• 2002

Radar method can be effective in probing concrete structures damaged by earthquake. Data analysis is usually performed in time domain, by considering time delay of the wave due to the dielectric constant of concrete. In this study, improved data analysis has been performed using signal processing scheme of spectra analysis and filtering. Three antenna with 900MHz, 1㎓, and 1.5㎓ center frequency were used to detect a steel bar or delamination in specimens for obtaining data, Frequency spectrum was filtered in low pass, high pass, and band pass varying cutoff frequency with 1/3 octave in frequency domain. The most effective cutoff frequency for each frequency has been determined as the range for 2 octave lower to 1 octave higher and 2 octave lower to 1 octave lower. This result provided a basis in improving data analysis capability using frequency domain filtering.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.10B
• /
• pp.1885-1894
• /
• 1999

The higher mode cutoff frequencies in Crawford TEM cells computed by the Galerkin method(GM) describe in this paper. The authors also report the half mode boundaries to solve not only the cut-off frequencies of symmetric TEM cells and those of asymmetric TEM cells. It is shown that the measured resonant frequencies of the present symmetric TEM cells and a designed asymmetric TEM cell are agreed with the calculated results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.533-541
• /
• 2001

In this paper, we proposed lowpass filter using all-pass sums of flat delay characteristics. this filter consisted of all-pass filter of parallel structure, the general analog filter is impossible to adjust the phase and the delay, using the Proposed filter, it has advantage to adjust them. And, we compared and analyzed this filter with passband width and magnitude characteristics, and the relation of group delay characteristics and cut-off frequency. Also, in order to obtain desired cut-off frequency, forming the weighing, we obtained desired cut-off frequency and group delay characteristics.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1601_1602
• /
• 2009

본 논문은 SSN(Simultaneous Switching Noise) 이 유전체를 통해 다른 시스템에 유기되는 것을 막기 위한 방법인 EBG(Electromagnetic Band-Gap)에 관한 연구이다. 이에 대한 EBG 구조를 설계하기 위해 PDN(Power Delivery Network)에 주기적인 패턴을 삽입한다. 패키지에 EBG 구조를 적용하기 위해 인쇄 회로기판 범위에서 연구되었던 구조를 변형 및 개조하여 EBG 구조가 내포하고 있는 필터의 차단 주파수의 범위를 넓히며 차단 시작 주파수를 1GHz 아래로 낮추는 소형화 방법을 모색한다. 이 연구에서 실시할 EBG 구조에 대한 간단한 고찰과 인쇄 회로 기판에 적합한 AI-EBG(Alternating impedance Electromagnetic Band-Gap) 구조를 이용한 EBG 의 소형화에 대해 언급하고, 소형화를 위한 3-D EBG 의 설계구조에 대해 설명한다. 그리고 저주파에서 차단특성을 높이기 위한 방법으로 3-D EBG를 사용하고 AI-EBG와 비교하여 차단특성의 변화를 Full-wave 시뮬레이션과 측정으로서 비교한다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.261-262
• /
• 2015

전력계통의 주파수 변화는 부하와 발전력 간 불균형에 의해 발생한다. 발전력 부족에 의해 수급 불균형이 발생한다면 계통 주파수는 부하와 발전력 간의 균형이 다시 이루어지는 점까지 저하하게 되며, 부하와 발전력 간의 수급균형이 이루어지지 않으면 계통은 붕괴된다. 저주파수 부하차단은 일정 시간 내에 부하와 발전력의 균형을 맞춤으로써 계통 붕괴를 방지하기 위한 것이다. 국내의 전력계통은 시간이 지날수록 점점 변화되고 있다. 예를 들어 태양광, 풍력 등의 신재생 에너지인 분산전원, 전력저장 장치 등이 계통의 한 부분이 되고 있는 것이 그 예이다. 이런 변화에 따라 저주파수 부하차단의 방식도 이런 변화를 염두에 두고 적용돼야 한다. 따라서 계통 변화에 따른 저주파수 부하차단 관련 규정 또한 변화가 필요하다.