• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.63-67
• /
• 2015

White light-emitting diode (WLED) is growing interest in using both illumination and communications. This paper reports visible light communication (VLC) composed of a super bright white light-emitting diode, low cost commercial photo-diode and a Fresnel lens. LED driver is consisted of the power MOSFET and MOSFET driver that switches the LED on and off. The modulation bandwidth of the LED used was determined to be 8 MHz. However, it was possible to communicate up to 1 Mbps under illumination of 500 lx because of the weak signal power and a low spectral sensitivity of the SHF213 as a PIN photodiode. In order to enhance the system bandwidth, the LED light was focused on the PIN photodiode by use of the Fresnel lens. As a result of that, visible light link was operated up to modulation bandwidth of the LED. The signal to noise ratio can be improved by 40 dB using an optical concentration at the receiver.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.4
• /
• pp.471-477
• /
• 2014

Purpose: We have analyzed the transmittance distribution of the ocular lens using local transmittance microscope to investigate the optical homogeneity of the lens. Methods: The transmittance of the laser which is focused on the surface of the ocular lens was measured by using the photo-detector and lock-in amplifier and analyzed. Multi-coated, uncoated, and progressive lenses were analyzed. Results: In the measurement of the progressive lens and a physical stimulated lens, local transmittance microscopy analysis showed a high degree of match with the measurement results through the optical microscope. In addition, the average value of the transmittance is reduced and the standard deviation was increased in the presence of optical defects. In unstimulated lens, there are a large impact on transmittance whether the anti-reflective coating is presence or absence in both the local transmittance microscopy and general transmittance analysis. Conclusions: The distribution of the transmittance measured by local transmission microscopy were changed when the various stimulus is applied to the lenses. These analyzes by local transmission microscopy can be utilized as a way to evaluate or determine the uniformity of the coating film or lens.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.304-304
• /
• 2012

III-V 화합물 태양전지는 실리콘 등 다른 태양전지에 비해 1sun상 30% 이상의 고효율을 갖고 있고 direct bandgap과 높은 이동도 등의 물질특성과 3족과 5족의 비율 조절로 같은 결정구조에서 에너지 bandgap이 다른 물질들을 만들기에 용이하여 태양전지 스펙트럼의 넓은 영역을 흡수할 수 있는 장점이 있다. 그러나 셀 자체의 물질이 실리콘에 비하여 고가여서 고성능이 요구되는 우주 인공위성 등에 적용이 되었지만, 2000년대 이후로 집광에 적용 가능한 태양전지의 연구를 거듭하여 2005년부터는 값싼 프레넬 렌즈를 이용하여 1 sun에 비해 500배 해당하는 빛을 셀에 집광하여 보다 효율을 증가시킴으로써 지상발전용에도 적용 가능한 셀을 형성하게 되었다. 더불어 태양전지의 효율을 증가시키기 위한 다양한 구조적 변화의 시도도 많이 이루어지고 있다. 최근 실리콘 태양전지의 표면에 texture 구조를 주어 높은 흡수율과 낮은 반사율을 갖게 함으로써 효율을 증가시키는 사례가 많아지고, III-V 화합물 태양전지도 texturing에 의해 증가된 효율을 발표한바 있다. 본 연구에서는 III-V 화합물 InGaP 태양전지의 window층으로 사용되는 InAlP 층에 Metal-assisted chemical etching (mac etching) 방법으로 texture 구조를 형성하여 etching 시간에 따른 InAlP층의 표면 변화와 반사율의 변화를 분석하였다.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.1
• /
• pp.31-36
• /
• 2011

CF(Circular Fresnel) POF(Plastic Optical Fiber) daylighting system is a beam daylighting system utilizing solar direct beam radiation. In this study, a CF POF daylighting system has been introduced, developed and applied to KIER test buildings. The CF POF daylighting system consists of three parts: light collector, light transmitter and light diffuser. The light collector includes a Circular Fresnel lens focusing solar direct illuminance by sun tracking. The light transmitter contains the POF cable which has light transmission loss of 4.5% per meter. The light diffuser has about 80% diffuser efficiency. This study aims to evaluate of POF daylighting system performance. At the results of a CFPOF system performance evaluation, the theoretical CFPOF system efficiency was 41.9% and the actual CFPOF system efficiency at the KIER test building was 37.5%. The difference was due partly to the connecting efficiency.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.96-101
• /
• 2012

An experimental study was conducted to investigate the performance of a concentrating photovoltaic cell (CPV) against temperature. It is know that a high efficiency of a CPV can be achieved only with proper cell temperature as well as high concentration ratio (CR). This study is concerned with appropriate cooling condition for a liquid-convection cooler for the best performance of a specific CPV. A series of experiments was conducted in a range of cell temperatures as a result of varying cooling conditions, while the concentration ratio was 390 and the solar irradiation flux was higher than 900 $W/m^2$ in outdoor environment. The CPV had a planar dimension of 10 by 10 mm. A Fresnel lens was used as a concentrator, of which the dimension was 221 mm(W) ${\times}$ 221 mm(L) ${\times}$ 3 mm(t) and the transmissivity was known to be 0.8. The cooler was attached to the bottom side of the CPV and had a contact area of 21 mm(W) ${\times}$ 26 mm(L), which was identical to the size of the base plate of the CPV. The coolant temperature was controlled by an isothermal bath and the flow rate was controlled and measured by a flowmeter. The experimental results showed that the average of power efficiency of the CPV decreased from 28.6 % to 24.7 % as the cell temperature increased from $36^{\circ}C$ to $97^{\circ}C$. An appropriate cooling method of a CPV might increase the power conversion efficiency by about 4% for the same concentration ratio. Discussion is included from the viewpoint of the combined efficiency in addition to the power efficiency.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.519-526
• /
• 2004

We developed a 2-D imaging system to detect ultra weak biophoton by using a high sensitive fast CCD camera. We installed an illumination apparatus to generate delayed luminescence from plant leaves. Shutters at the illumination system and detector were synchronized to each other. The lens system of the CCD camera was newly designed to accommodate the specific requirements to enhance the collection efficiency for biophoton. Based on the lens simulation, commercial lenses were chose for the lens system. All the equipment was installed in a multi-purpose dark box and the delayed luminescence of Euonymus japonica was successfully acquired.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.3
• /
• pp.299-305
• /
• 2015

In this paper, we propose a simple and low-cost fabrication method of polymer microlens using solvent-vapor-assisted reflow (SVAR). Metal molds for replication of polymer were fabricated using micro milling and the cylindrical shape of polymer was imprinted using hot-embossing process. The cylindrical shape of polymer was changed to hemispherical lens shape by SVAR. The characteristics of fabricated microlens were evaluated according to the condition of SVAR such as temperature and time. The focal length of polymer microlens could be controlled more easily in low-temperature and long-time condition than in high-temperature and short-time condition. That is, the level of concentrated light to focal point could be improved through the control of temperature and time. Also, we confirmed that toluene was more appropriate solvent than acetone in fabrication of PMMA polymer microlens using SVAR.

• Korean Journal of Optics and Photonics
• /
• v.30 no.3
• /
• pp.101-105
• /
• 2019

An LCD backlight unit (BLU) using RGB light sources is designed and simulated, in order to improve its optical energy efficiency. A color-matching BLU is designed with a lenticular lens array (LLA) with elements that image the linear RGB light sources onto the RGB subpixels of the color filter. Type-A and Type-B simulations are performed, according to the location of the light sources. As a result, the luminance increases to 210% in Type-A and 270% in Type-B respectively. The optimum values for the height and the gap of the LLA for maximum efficiency are found to be $25{\mu}m$ and $3{\mu}m$ respectively.

• JOURNAL OF ELECTRICAL WORLD
• /
• s.257
• /
• pp.78-82
• /
• 1998

CD(Computer Disc) 의 약 7배의 용량을 가진 디스크와 그 관련기기가 시판되기 시작했다. DVD(Digital Versatile Disc), DVD-ROM이라는 이 기기는 디스크위에 집광되는 광스포트의 크기를 작게 하여 기록밀도를 높이기 위해, 대물렌즈의 NA,를 0.6으로 크게 하였고(CD에서는 NA가 0.45)광원이 되는 레이저의 파장도 650mm대로 단파장화(CD에서는 780nm)하였다. 이의 실현을 본격화하기 위해서는 DVD에 대응할 수 있는 대용량의 기록미디어와 장치가 필요하다. 이미 CD-R을 비롯한 몇 가지의 추기형, 서환형의 DVD-RAM 등이, 재생전용 DVD가 시판되기 이전부터 제안되어 규격화되었으며 미쓰비시전기에서도 그것에 조준을 맞추어 광원이 되는 고출력 반도체레이저의 개발과 제품화를 추진하여 온 것이다. 여기서는 다음에 제시하는 DVD-RAM용 반도체레이저에 대한 요구성능과 이를 실현하기 위한 방법 및 결과에 대하여 기술한다. $\cdot$파장 650nm대에서 30~50mW의 높은 광출력을 얻을 수 있는 활성층의 재료와 구조의 개발 $\cdot$60$^{\circ}C$의 고온에서도 동작전류 증가가 적은 활성층구조의 최적화 $\cdot$고온, 고출력의 장시간 동작에서도 발광부 단면의 열화를 방지 할 수 있는 단면 강화기술의 개발 동사는 이들 기?과 과제에 대하여 검토를 거듭한 결과 DVD-RAM광원에 적합한 고출력 반도체레이저(MLIxx6시리즈)의 제품화를 실현할 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1179-1180
• /
• 2005

3D micro scaled shapes are fabricated with the method of direct writing and superposing grooving in ambient air using femto-second laser pulses and copper, aiming at establishing an industrially useful femto-second laser processing machine to be able to fabricate three dimensional micro-scale structures, especially micro scaled molds, and processing techniques. For the several advantages, there is no thermally influenced region around the area irradiated by the laser beam and surfaces irradiated laser beam are smooth and substances ablated to form are no attached on the surface of works and so on, the femto-second laser technology is anticipated for advanced micro/nano precision technology.