• 한국재료학회지
• /
• 제5권4호
• /
• pp.468-475
• /
• 1995

활성금속 브레이징 방법으로 스테인레스 스틸과 질화규소를 접합하여 기계적 특성 및 유한요소법을 사용하여 접합체에서 발생되는 잔류응력의 크기를 조사하였다. 고강도 접합체를 제조하기 위하여 연성금속인 Cu 및 Cu/Mo 적층체를 중간재로 사용하였으며, 중간재의 두께 및 구조에 따라 접합체에서 발생되는 잔류응력의 크기 및 분포가 접합강도에 미치는 영향에 관하여 조사하였다.중간재인 Cu의 두께가 0.2mm 일대 세라믹스에 발생되는 최대 잔류응력의 크기가 급격히 감소하였으며, 최대 접합강도가 나타났다. Cu/Mo 다층 중간재를 사용한 접합체에서는 Cu/Mo 두께비가 감소할수록 접합강도는 증가되었다. 스테인레스 스틸/질화규소 접합체에서 Cu/Mo 중간재의 사용은 Cu 중간재 사용보다 접합강도를 증가시키는데 효과적이었으며, 최대 접합강도는 450Mpa 정도이었다. Cu/Mo 중간재를 사용한 접합체에서는 Mo에 최대 인장방향의 잔류응력이 발생하여 강도 측정시 Mo의 지배적인 소성변형으로 잔류응력이 감소되어 접합체의 접합강도를 향상시키는 것으로 생각된다.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.101-112
• /
• 1994

The measurement of residual stress distribution of $Si_3N_4/SUS304$ joint was performed on 23 specimens with the same joint condition using PSPC type X-ray stress measurement system and the two-dimensional elastoplastic analysis using finite element method was also attempted. As results, residual stress distribution near the interface on the ceramic side of the joint was revealed quantitatively. Residual stress on the ceramic side of the joint was turned out to be tensional near the interface, maximum along the edge, varying in accordance with the condition of the joint and variance to be most conspicuous for the residual stress normal to the interface characterized by the stress singularities. In the vicinity of the interface, the high stress concentration occurs and residual stress distributes three-dimensionally. Therefore, the measured stress distribution differed remarkably from the result of the two-dimensional finite-element analysis. Especially at the center of the specimen near the interface, the residual stress, $\sigma_{x}$ obtained from the finite element analysis was compressive, whereas measurement using X-ray yielded tensile $\sigma_{x}$. Here we discuss two dimensional superposition model the discrepancy between the results from the two dimensional finite element analysis and X-ray measurement.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.251-258
• /
• 1996

The reactions between an active metal brazing alloy and interlayers together with the effects of interlayer type on the interfacial microstructure change were investiaged for silicon nitride/stainless steel joint. The bending strengths were measured for joints with Mo, Cu, Ni interlayer type of different thicknesses. It was found that the interlayer with a low yield strength value is effective to improve the bending strength of the Si3N4/stainless steel joint. The maximum joint strength obtained at room temperature for a laminated Cu/Mo interlayer was about 460 MPa. The combined use of Mo and thin Cu layer was found to be effective in enhancing the bending strength for the Si3N4/S.S.316 joint.