• Applied Microscopy
• /
• v.30 no.4
• /
• pp.337-345
• /
• 2000

Introduction of the buffer layer and the nitridation of a sapphire substrate were one of the most general methods employed for the reduction of lattice defects in GaN thin films Brown on sapphire by MOCVD. In an effort to improve the initial nucleation and growth condition of the GaN, reactive ion beam (RIB) of nitrogen treatment of the sapphire surface has been attempted. The 10 nm thick, amorphous $AlO_xN_y$ layer was formed by RIB and was partially crystallized alter the main growth of GaN at high temperature, leaving isolated amorphous regions at the interface. The beneficial effect of amorphous layer at interface in relieving the thermal stress between substrate and GaN film was examined by measuring the lattice strain value of the GaN film grown with and without the RIB treatment. Higher order Laue zone pattern (HOLZ) of $[\bar{2}201]$ zone axis was compared with simulated patterns and lattice strain was estimated It was confirmed that the great reduction of thermal strain was achieved by RIB process and the amount of thermal stress was 6 times higher in the GaN film grown by conventional method without the RIB treatment.

• Journal of Environmental Health Sciences
• /
• v.34 no.5
• /
• pp.374-381
• /
• 2008

In this study, the factors affecting biological N and P removal using SND (simultaneous nitrification and denitrification) process were investigated and evaluated to examine the possibility of treating N and P through SND with NADH by surveying N and P traces in an aeration tank. Variations of $NH_4^+$-N+$NO_3^-$-N concentration were used to estimate the degree of SND in each point (P2, P3, P4, P5) of the aeration tank and these variations showed that denitrification efficiency in P2 (front zone), nitrification and denitrification efficiencies in P4 (middle zone) were 67%, 86% and 39%, respectively. When $PO_4^{-3}$-P concentration was analyzed in each point of the aeration tank, it was shown that $PO_4^{-3}$-P concentration coming into P2 was 1.25 mg/L, which increased to 2.22 mg/L by P release in P2 zone and then decreased to 0.74 mg/L by P uptake in P4. Consequently, we were able to estimate which high P removal efficiency observed in this study was caused by biological phosphorus removal. To determine the operating factors affecting effluent T-N, we analyzed the correlation among FN/M ratio, C/N ratio, Temp., SRT etc and these results showed that the correlation among FN/M ratio, C/N ratio and Temp was not high. However, the relationship of SRT and other parameters (effluent $NH_4^+$-N and effluent BOD) and the short SRT could have an affect on effluent $NH_4^+$-N and so effluent BOD could be increased. Thus, SRT operation should be controlled over 10 days. The results for analyzing the correlation between SRT and influent $NO_3^-$-N in order to investigate the operating factors affecting effluent T-P showed that T-P or $PO_4^{-3}$-P was not highly correlation with SRT, whereas $PO_4^{-3}$-P concentration increased along with increasing $NO_3^-$-N concentration into P2. Based on these results, we concluded, using regression analysis (R2=0.97), that effluent $PO_4^{-3}$-P concentration depends on $NO_3^-$-N concentration into P2.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3740-3747
• /
• 2009

To protect the citizens' health of Gyeongju and to secure basic data for the assessment of health and environmental risk, distribution characteristics of meteorological elements were investigated and numerical simulation of wind field using RAMS model was carried out. In addition, measurement and analysis of air pollutants, forecasting the behavior air pollutants using ISC-AEROMOD view, and health and environmental risk-influenced zones were defined through managing air polluting materials to prevent health damage and property damage. According to the survey results of air pollution in Gyeongju and surroundings, average annual concentration of air pollutants in Gyeongju was slightly lower than that in Pohang and Ulsan areas, but concentration of particulate matters and nitrogen dioxide at Gyeongju Station Square and Yonggang Crossing were sometimes higher than that in Pohang and Ulsan areas. Results of the modeling of moving and diffusion of air pollutants that affect citizens' health showed that parts of the 1st through 4th industrial complexes together with POSCO were included in particulate matters and sulfur dioxide influenced areas in Pohang Steel Complex area, and that Haedo-dong, Sangdae-dong, Jecheol-dong and Jangheung-dong in Pohangnam-gu represented locally worsened air quality due to a quantity of air pollutant emission from dense steel industries and large scale industrial facilities.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1756-1761
• /
• 2006

본 연구의 목적은 임진강 유역을 대상으로 2005년에 발생한 유출특성을 분석하는데 있다. 임진강 유역은 유역전체 면적중 2/3이상이 북한지역에 위치하고 있어서 전체적인 수문관측 자료를 수집하기 어려운 상황에 있으나, 가용한 수문관측 자료 및 유량측정성과를 이용하여 5개 지점에 대한 유출특성을 분석하였다. 임진강 유역에서는 30분 단위의 연속적인 우량 및 수위관측(건설교통부)을 하고 있으며, 기상청에서는 1시간 단위의 기상관측을 하고 있다. 우량 및 수위자료의 수집과 검토를 통하여 유역면적우량과 5개 수위관측소의 수위를 최종 확정하였다. 그리고 2005년에 측정한 유량측정성과를 통하여 유량측정성과에 대한 불확실도, 기본 수리특성 분석, 수위-유량관계곡선식을 개발하여 유량을 산정하였다. 산정된 유량은 월별, 주요 호우사상별 유출률 분석을 통하여 합리적인 유출률 범위내에서 재 조정절차를 거쳐 최종 유량을 확정하였다. 산정된 유출률은 57.0%(영중)${\sim}$72.1%(적성)의 유출률을 보였으며, 2004년 임진강 유량측정용역 보고서의 유출률과 비교한 결과 일부지점을 제외하고는 비교적 일치하는 것으로 나타났다. 임진강 유역의 일부인 설마천 시험유역에서의 2005년 연간 유출률은 60.9%로 상기의 값은 매우 타당하다고 할 수 있다. 그리고, 남북한 수문자료의 공유 및 기술적 교류, 유역 전체의 정밀한 수문관측 및 신뢰성 있는 수문자료 생성이 이루어진다면 보다 정확한 유출특성 거동을 분석할 수 있을 것이며, 효과적인 치수 및 이수계획의 수립 등 수자원 개발을 위한 기반을 확보할 수 있을 것이다.수리모형실험과 연계하여 댐 설계에 효율적으로 사용될 수 있을 것으로 전망된다.지는 것으로 평가되었다. 그러나 본 연구결과를 통하여 투수성 포장과 지하수에 관련된 매개변수의 집적과 분석결과는 현장기술 적용 시 매개변수의 유용한 선택과 도시유역의 물 순환 건전화 대안기술 적용에 효과적인 방법론을 제시할 수 있을 것으로 사료된다.첨두홍수량을 저류하기 위해서 상대적으로 넓은 저류면적이 필요한 것으로 나타난다. 대등한 수위감소값의 홍수저감효과를 발휘하기 위해서 본 연구에서는 On-Line 저류지 면적은 Off-Line 저류지에 비 두배 이상이 필요한 것으로 보여졌다.들에 관한 정보는 종종 현장관측에서 조차 무시되는 경우가 많다. 이에 본 연구에서는 수질모형의 매개변수 중 특히 수리특성에 관련된 매개변수들이 수질에 미치는 영향을 파악하는 것을 목적으로 하고 있다. 이를 위해 적용된 수질모형은 QualKo를 사용하였으며, 대상 하천은 낙동강 본류 경남구간 시점 부근인 회천 합류 전부터 낙동강 본류 경남구간 종점 부근인 밀양강 합류 전까지의 경남 오염총량관리 기본계획 시 구축된 모형 매개변수를 바탕으로 분석을 수행하였다. 일차오차분석을 이용하여 수리매개변수와 수질매개변수의 수질항목별 상대적 기여도를 파악해 본 결과, 수리매개변수는 DO, BOD, 유기질소, 유기인 모든 항목에 일정 정도의 상대적 기여도를 가지고 있는 것을 알 수 있었다. 이로부터 수질 모형의 적용 시 수리 매개변수 또한 수질 매개변수의 추정 시와 같이 보다 세심한 주의를 기울여 추정할 필요가 있을 것으로 판단된다.변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기

• Journal of Wetlands Research
• /
• v.13 no.3
• /
• pp.707-720
• /
• 2011

For the lake case, the detention phenomenon of water body occurs and stays for a long time. Especially, following the layer of water depth direction, the lake body and water quality problems are different from the water quality of river. So according to time, the stream and water quality can be simulated by the 3-Dimensional Model, which can divide water layer for reservoir or lake. The water quality simulation result will become more reliability. For this study, the 3-Dimension Model - EFDC was used to simulate water quality of Unam reservoir in the Sumjin Dam. The HEC-GeoHMS and HEC-HMS Rainfall - Runoff Model based on GIS were used to estimate long-term runoff, and input data was constructed to the observed water level, meteorological data, water temperature, T-N and T-P. In order to apply the EFDC model, water depth was divided into 3 layers and 5,634 grids were extracted. After constructing the grid net, the water quality change of Unam reservoir in time and space was simulated. Overall, long term runoff simulation reflected the actual observed runoff well, through the water quality simulation, according to the pollution factors, the behavior characteristics can be checked, and the simulated water quality can be properly reflected. The function of EFDC has been confirmed, which water quality can be properly simulated. In the near future, to establish countermeasures for Intake Facilities of Watershed and Management, this support which some basic tools can be applied is in expectation.

• Analytical Science and Technology
• /
• v.6 no.5
• /
• pp.417-424
• /
• 1993

Eight-coordinate tetrakis molybdenum(IV) complexes containing 5,7-dichloro-8-hydroxyquinolinol(Hdcq) and 2-mercaptopyrimidine(Hmpd) has been prepared. $Mo(mpd)_4$, $Mo(dcq)(mpd)_3$, $Mo(dcq)_2(mpd)_2$, $Mo(dcq)_3(mpd)$ and $Mo(dcq)_4$ complexes have been isolated by thin-layer chromatography on silicagel plates. These complexes have been charaterized by $^1H-nmr$ spectrum and UV-Vis. spectrum. The chemical shift values of the protons ${\alpha}$ to the nitrogen in the ligands are shifted to down field. The relative intensities of the peaks which are positioned at the same proton of $Mo(dcq)(mpd)_3$ and $Mo(dcq)_3(mpd)$ are observed in 2:1 ratio, in case of $Mo(dcq)_2(mpd)_2$ appears in approximately a 1:1 ratio. The stereochemistry of the complexes in discussed in terms of their nmr spectrum and Orgel's rule. By vertue of the intensities (${\varepsilon}$>10,000~25,000) the low energy($16,600{\sim}19,800cm^{-1}$) bands are observed for the electronic spectra of the complexes are assigned as charge transfer bands.

• Clean Technology
• /
• v.23 no.1
• /
• pp.80-89
• /
• 2017

The bubbling fluidized bed (BFB) reactor with a diameter of 0.1 m and a height of 1.2 m was used for experimental study of co-firing and emission characteristics fueled by sewage sludge (SS) and wood pellet (WP). The facility consists of a fluidized bed reactor, feeding system, cyclone, condenser and gas analyzer, The mean particle diameter and minimum fluidization velocity are $460{\mu}m$ and $0.21ms^{-1}$ respectively. SS produced from Korea and WP from Canada were examined. The various mixing ratios of WP were 20, 50, and 80% based on HHV. The equivalence ratio of 1.65, reactor temperature of $800^{\circ}C$, air flow rate of $100Lmin^{-1}$, and fluidization number of 4 were fixed in the BFB experiment. In TGA, the range of combustion temperature of SS was wider than that of WP. It represents that the combustibility of WP is higher than that of SS. The BFB reactor temperature was maintained between 800 and $900^{\circ}C$. CO emission of SS was high because of lower combustibility. $NO_X$ and $SO_X$ formation of SS were higher than that of WP since high nitrogen and sulfur contents of SS. CO, $NO_X$, and $SO_X$ formation were suppressed as the mixing ratio of WP was increased. The slagging and fouling tendencies show high in all test conditions.

• Fire Science and Engineering
• /
• v.16 no.3
• /
• pp.26-31
• /
• 2002

Bromotrifluoromethane(halon-1301) and bromochlorodifluoromethane(halon-1211) have been widely used as a clean fire extinguishing agents due to their outstanding properties. However, production and use of halon are currently being phased out under an international agreements Montreal Protocol because of global environmental concerns and HFCs have been considered as promising alter-natives for the replacement of halon since their ozone depletion potentials are low. The vapor-liquid equilibrium data are required as important basic information in evaluating the solubility of clean fire extinguishing agents and determining their optimal compositions. In this work, we chose HFCs such as HFC-22 HFC-125, and HFC-l34a for gaseous fire extinguishing agents and nitrogen as a pressurization gas for a proper jet velocity of these agents. Phase equilibria for binary mixtures of nitrogen/HFC-22, nitrogen/HFC-125, and nitrogen/HFC-l34a were measured in the temperature range from 283.15K to 303.15K. For equilibrium measurement, we used a circulation type apparatus in which both vapor and liquid phases were continuously recirculated. The experimental data were relatively well correlated with the Peng-Robinson equation of state with Wong-Sandier mixing rules.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.221-232
• /
• 2018

The silica containing carbon ($C-SiO_2$) membranes were fabricated using poly(imide siloxane)(Si-PI) and polyvinylpyrrolidone (PVP) blended polymer. The characteristics of porous carbon structures prepared by the pyrolysis of polymer blends were related with the micro-phase separation behaviors of the two polymers. The glass transition temperatures ($T_g$) of the mixed polymer blends of Si-PI and PVP were observed with a single $T_g$ using differential scanning calorimetry. Furthermore, the nitrogen adsorption isotherms of the $C-SiO_2$ membranes were investigated to define the characteristics of porous carbon structures. The $C-SiO_2$ membranes derived from Si-PI/PVP showed the type IV isotherm and possessed the hysteresis loop, which was associated with the mesoporous carbon structures. For the molecular sieving probe, the $C-SiO_2$ membranes were prepared with the ratio of Si-PI/PVP and the pyrolysis conditions, such as the pyrolysis temperature and the isothermal times. Consequently, the $C-SiO_2$ membranes prepared by the pyrolysis of Si-PI/PVP at $550^{\circ}C$ with the isothermal time of 120 min showed the $O_2$ permeability of 820 Barrer ($1{\times}10^{-10}cm^3(STP)cm/cm^2{\cdot}s{\cdot}cmHg$) and $O_2/N_2$ selectivity of 14.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2006.04a
• /
• pp.247-252
• /
• 2006

오염 퇴적물내 중금속의 방출과 이에 따른 생이용성(bioavalability)은 기존의 가역 평형관계로써 설명하기에 불충분한 것으로 알려져 있다. 최근 연구결과에 의하면 이러한 탈착 저항성을 설명하기 위한 비가역적 모델에 의해 퇴적물내 중금속의 탈착저항성 부분이 존재함이 밝혀졌다. 탈착저항성에 대해서는 아직 충분한 규명이 이루어지지 않았으나, 오염물질의 노화(aging)에 의해 일단 탈착저항성을 띠게 되면 생이용성(bioavailability)이 감소되는 것으로 알려져 있다. 본 연구에서는 노화(aging)가 연안 퇴적물 내 납과 카드뮴의 흡/탈착 특성에 미치는 영향을 알아보기 위해 연속 탈착실험과 biphasic 탈착모델을 적용함으로써 납과 카드뮴의 탈착저항성을 규명하고자 하였다. 그리고 연속 추출 실험을 통해서 노화(aging)에 따른 퇴적물 내 납과 카드뮴의 흡착 기작을 규명하고자 하였다. 연속탈착 실험 결과 시간이 경과함에 따라 탈착저항성부분의 크기가 증가하였으며, 연속추출 실험 결과 납의 경우 carbonate fraction에서 추출된 납이 가장 많았으며, 노화(aging) 따라 exchangeable fraction에서 추출된 납이 감소하는 반면 reducible, organic material, residual fraction에서 추출된 납의 양이 증가하였다. 카드뮴의 경우 가장 많은 양이 추출된 단계는 exchangeable fraction이였으며, organic material fraction에서는 카드뮴이 추출되지 않았다. 노화(aging) 따라 reducible fraction과 residual fraction에서의 추출량이 증가하는 경향을 보였으나 그 양은 매우 적은 것으로 나타났으며, 노화(aging)에 따른 exchangeable fraction과 carbonate fraction에서의 추출량은 큰 변화가 없었다. 대해서는 북한지역의 분포상황을 밝혔다.것을 알 수 있었으며, 크롬과 비소의 경우는 초기에 많이 용출되고, 구리의 경우는 꾸준히 용출되는 것을 알 수 있었다. 3년 된 통나무집이 8년 된 통나무집보다. 용출양이 더 컸으며, 이는 CCA성분이 초기에 많이 용출된다는 것을 의미한다. 억제 효과를 나타내었고 Hep3B에서는 부탄을 분획물 (1 mg/mL)에서 82%의 비교적 높은 성장억제효과를 나타내었다.as a "front" and "back". Thus, Germany′s private space may face a genuine public space and street, which is rare in the Korean housing. Although the layout of indoor space in the korean housing tends to be open, such an openness may be outstanding in living and dining spaces, kitchen and various accesses to rooms. In the case of Germany, such indoor spaces are usually closed to each other. Thus corridors act to separate these spaces. Such differences are analysed to be due to the different perceptions of interpersonal and socio-cultural attributes as intra-family and inter-neighbor relationships or communications. 알 수 있었다.도 질소와 인산처럼 토양지지대가 있는 경우가 낮은 함량을 유지하였다.pe from the daily life, to fantasize and daydre