• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.755-760
• /
• 2016

The demand for independent generators using renewable energy has been increasing. Among those independent generators, small wind turbine generators have been actively developed. Permanent magnets are generally used for small wind turbine generators to realize a simple structure and small volume. On the other hand, cogging torque is included due to the structure of the permanent magnet synchronous machine, which can be the source of noise and vibration. The cogging torque can be varied by the shape of the permanent magnet and core, and it can be reduced using the appropriate design techniques. This paper proposes a design technique that can reduce the cogging torque by changing the shape of the permanent magnets for SPMSM (Surface Permanent Magnet Synchronous Motor), which is used widely for small wind turbine generators. Evolution Strategy, which is one of non-deterministic optimization techniques, was adopted to find the optimal shape of the permanent magnets that can reduce the cogging torque. The angle and outer diameter of permanent magnet were set as the design variable. A 300W class wind turbine generator, whose pole/slot combination was 8 poles/18 slots, was designed with the proposed design technique. The properties of the generator, including the cogging torque and output voltage, were calculated. The calculation results showed that the cogging torque of the optimized model was reduced compared to that of the initial model. The design technique proposed by this paper can be an effective measure to reduce the cogging torque.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.364-373
• /
• 2015

This study was carried out to estimate the effects of density and mixing ratio of mandarin peels on the bending performances of the sawdust-mandarin peels particle boards. The board density influenced significantly to the bending performance of boards. Dynamic modulus of elasticity (dMOE) and static modulus of elasticity (sMOE) and modulus of rupture (MOR) of particle boards decreased with an increase in the mixing ratio of mandarin peels at the board densities of $0.4g/cm^3$ and $0.5g/cm^3$. High correlations were found between the dMOE and sMOE, and dMOE and MOR of particle boards prepared. Therefore, it was concluded that the dMOE obtained by free vibration test using resonance frequency could be used for predicting the sMOE and MOR of sawdust-mandarin peels particle boards.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.1
• /
• pp.35-42
• /
• 2010

The rapid economic development induced the massive road constructions, becoming bigger and high-speed of the vehicles. However, it brings lots of social problems, such as air pollutions, traffic noise and vibration. Special concrete block for the base course of asphalt pavement is needed to decrease traffic noise such as tire's explosive and vehicles sound, applying Helmholtz Resonators theory to asphalt pavement. If it is applied to the area where it happens considerable noise such as a junction, the street of a housing complex and a residential street, it is one of considerable method to solve the social requirements of noise problem. This research examines couple of laboratory tests for the sound absorption effect of the concrete block and the base concrete block. There are specimens which is fixed hall-size, space, depth as the condition of this research, and these are analysed of noise decrease effect using different condition of the first noise of each vehicle. As a result of analysis data according to vehicle noise volume, measurement distance, a form and size of the hall using the base concrete block, the use of special concrete base showed a good alternative solution for decreasing traffic noise level, from 4 dB to 9 dB.

• Korean Journal of Medicinal Crop Science
• /
• v.6 no.1
• /
• pp.57-61
• /
• 1998

Angelica gigas, Astragalus membranaceus and Ligusticum chuanxiong have been grown for a long time in Korea as medicinal crops with underground parts. Its harvesting method has been depended entirely on manual labor. Therefore, harvesting involved much work. This study was to determine an effective mechanized harvesting method for underground parts of some medicinal crops by several machines. Labor time was decreased by 61 percent in Angelica gigas and by 70 percent in Astragalus membranaceus by the use of poclain harvester, however, in Ligusticum chuanxiong was decreased 68 percent by multi - root harvester compared with conventional system (manual harvest). The poclain harvester was suitable for harvesting in Angelica gigas and Astragalus membranaceus plots, but multi - root harvester was not satisfactory. Multi - root harvester appeared to be appropriate harvester for Ligusticum chuanxing.

• Journal of the Korean Magnetics Society
• /
• v.3 no.3
• /
• pp.208-214
• /
• 1993

In order to investigate the origin of an increase in the coercivity with the Ta addition to Co-Cr films, the perpendicular magnetic anisotropy of Co-Cr film and CoCrTa film was measured by a torque magnetometer and VSM. In Co-Cr binary alloy film, the uniaxial anisotropy increased with increasing Cr content. The perpendicular magnetic anisotropy of $Co_{81.7}Cr_{16.7}Ta_{1.6}$ film was larger than that of $Co_{81}Cr_{19}$ film, both of which were deposited at the same substrate temperature of $100^{\circ}C$. The change in the perpendicular magnetic anisotropy with annealing was studied to understand the Ta addition effect. The amount of decrease in perpendicular magnetic anisotropy of the CoCrTa film by the annealing was larger than that of Co-Cr film. And the perpendicular magnetic anisotripies of Co-Cr film and CoCrTa film after annealing were almost the same. The cause of this was interpretated as the enhanced segregation of solute atoms in the Ta added thin film in the as-deposited state. The enhanced segregation of solute atoms increases the perpendicular magnetic anisotropy of the film, and causes the increase of perpendicular coercivity of the film.

• Journal of the Korean Magnetics Society
• /
• v.14 no.1
• /
• pp.33-37
• /
• 2004

Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$ has been studied with Mossbauer spectroscopy, x-ray diffraction, vibrating sample magnetometer (VSM), and magnetoresistance (MR) measurement. The crystal structure was determined to be a cubic spinel with lattice parameter a$_{0}$=9.9880 $\AA$. The MR measurements show a semiconductor behavior below 110 K and metal behaved above 100 K. The temperature dependence of magnetization of Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$ was reported. In addition to a large irreversibility between the zero-field-cooling (ZFC) and the field-cooling (FC) magnetization at applied field H=100 Oe, a cusp-like anomaly was observed in both the FC and ZFC curves. It shifted toward the lower temperature region with increasing magnetic field, and then showed convex type maximum at 110 K, under the applied field of 5 kOe. The Mossbauer spectra were measured from 15 K to room temperature. The asymmetric line broadening was observed for the sample Cu$_{0.1}$Fe$_{0.9}$Cr$_2$S$_4$, and it was considered to be dynamic Jahn-Teller relaxation. The charge state of Fe ions was ferrous in character. The unusual reduction of magnetic hyperfine field below 110 K was interpreted in terms of cancellation effect between the mutually opposite orbital current field (H$_{L}$) and Fermi contact field (H$_{C}$).

• Journal of the Korean Magnetics Society
• /
• v.10 no.3
• /
• pp.106-111
• /
• 2000

The magnetic thin films can be prepared without vacuum process and under the low temperature (<100 $^{\circ}C$) by ferrite plating. We have performed ferrite plating of M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$(x=0.00~0.08) films and N $i_{x}$Z $n_{0.22}$F $e_{*}$2.78-x/ $O_4$(x=0.00~0.15) films on cover glass at the substrate temperature 90 $^{\circ}C$. The crystal structure of the samples has been identified as a single phase of polycrystal spinel structure by x-ray diffraction technique. The lattice constant in the M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$films increases but in the N $i_{x}$Z $n_{0.22}$F $e_{*}$2.78-x/ $O_4$films decrease with the composition parameter, x. The saturation magnetization in the M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$films does not greatly change, in agreement with observations on bulk samples.k samples.k samples.

• Journal of the Korean Magnetics Society
• /
• v.18 no.5
• /
• pp.195-199
• /
• 2008

Composites of $Fe_{93.5}Si_{6.5}$ powder and epoxy were prepared using a thermal curing process. Scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and network analyzer were used to analyze the structure, electromagnetic properties and microwave absorption of the composites. Results show that the saturation magnetization depends on the fraction of the $Fe_{93.5}Si_{6.5}$ powder in the composite, which affects initial permeability. It is believed that the eddy current loss is a dominant factor over 1 GHz and that the resonance frequency of the composite decreases with increasing fractions of $Fe_{93.5}Si_{6.5}$ powder. Finally, reflection loss was calculated from the permeability and permittivity of these composites. Composite with 50 wt.% $Fe_{93.5}Si_{6.5}$ powder fractions and 5 mm thickness showed reflection loss below -20 dB from 3.66 GHz to 4.16 GHz. Therefore, it is believed that thin Fe-Si/epoxy composites may be a good candidate for microwave absorption application.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.4
• /
• pp.5-14
• /
• 2016

Numerical simulation of dynamic soil-pile-structure interaction embedded in a dry sand was carried out. 3D model of the dynamic centrifuge model tests was formulated in a time domain to consider nonlinear behavior of soil using the finite difference method program, FLAC3D. As a modeling methodology, Mohr-Coulomb criteria was adopted as soil constitutive model. Soil nonlinearity was considered by adopting the hysteretic damping model, and an interface model which can simulate separation and slip between soil and pile was adopted. Simplified continuum modeling (Kim et al., 2012) was used as boundary condition to reduce analysis time. Calibration process for numerical modeling results and test results was performed through the parametric study. Verification process was then performed by comparing numerical modeling results with another test results. Based on the calibration and validation procedure, it is identified that proposed modeling method can properly simulate dynamic behavior of soil-pile system in dry condition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.206-206
• /
• 2008

압전소자를 이용한 초음파 모터는 전자기적 원리로 동작하는 기존의 모터에 비해 구조가 간단하고 소형, 경량화가 가능하며 저속에서 큰 토크가 가능하고 ${\mu}m$단위 까지 정밀제어가 가능하다는 장점 등으로 인해 그 응용분야가 점차 확대되고 있다. 초음파 모터의 원리는 수평과 수직방향에서 변위가 타원형 운동을 형성하는 것이다. 따라서 선택한 타원운동의 방식에 의해서 모터의 형상이 달라진다. 초음파 모터는 액츄에이터를 사용하여 만들기 때문에 액츄에이터의 특성은 모터의 타원변위나 토크에 영향을 미친다. 단판형 액츄에이터에 비하여 적층 액츄에이터는 입력 임피던스를 낮추어 낮은 구동전압에서 구동이 가능하며 큰 변위와 토크를 발생하기 때문에 진동자의 수명 향상과 구동전압을 낮추기에 적합하다. 적층 액츄에이터는 변위량이나 응력 등을 개선하기 위해서 전기기계 결합계수(kp) 및 압전 d상수가 큰 재료가 요구되며, 고전압에서 장시간 구동 시 마찰에 의한 열손실을 감소시키기 위해 높은 기계적 품질계수(Qm)를 가져야한다. 적층 시 내부전극으로 사용하는 Pd, Pt가 함유된 전극은 가격이 비싸 제조비용을 상승시킨다. 상대적으로 값싼 Ag전극을 사용하면 비용절감을 할 수 있지만 융점이 낮아서 저온소결이 불가피하다. 따라서, 특성이 우수한 적층 액츄에이터를 제조하기 위해서 저손실, 저온소결 할 수 있는 액츄에이터 재료가 필요한 실정이다. L1-B4 혈 선혈 초음파 모터는 L1모드와 B4모드의 공진 주파수가 일치하여야 큰 변위를 얻을 수 있는데 이전의 논문에서 Atila를 이용한 시뮬레이션 결과를 분석한 봐 있다. 적층 액츄에이터의 층수를 5,7,9,11,13,15층으로 하여 L1-B4모드에서의 공진주파수를 비교한 결과 13 층일 때 두 모드가 비슷한 공진주파수를 보였고, 티원변위궤적도 다른 층수에 비해 크게 나타났다. 본 연구에서는 시뮬레이션 결과 가장 좋은 특성을 보인 13층 액츄에이터로 선형 초음파 모터를 제작하였다. 또한, 액츄에이터는 압전 및 유전특성이 우수한 저온소결 PZW-PMN-PZT세라믹을 이용하여 제작하였고, 내부전극으로 Ag전극을 사용하였다. 제작된 13 층 선형초음파모터를 가지고 프리로드 및 전압에 따른 속도를 조사하였고, 시뮬레이션 결과와 비교해 보았다.