• Journal of Korea Foundry Society
• /
• v.27 no.2
• /
• pp.88-94
• /
• 2007

General criteria for the risering design of steel castings and commercial codes for the flow and solidification analysis were used to design the optimized risering in V-process. Three type of specimens were chosen including thin plates and a thick disc. Sided riser installed in the front of a plate casting was effective to prevent the shrinkage defects and to increase the casting yield ratio. Exothennic sleeve and chill were also effective. It was possible to apply the general criteria for the risering design of steel castings to V-process. Temperature of a mold surface was expected to rise over $1,000^{\circ}C$ in the temperature calculation considering radiation effect of molten metal in the mold. Since weakening temperature of the vinyl used in V-process is about $70^{\circ}C$, it should be emphasized that a proper coating of the vinyl film is necessary to prevent the possibility of burning out of the vinyl by the molten metal.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.39-45
• /
• 1998

In the previous study. the powder casting was attempted as the rapid tooling. The powder casting was the process to cast dry powder into the casting mold transferred from R/P model and infiltrate the liquid binder to solidify the powder. And then, the melted copper was infiltrated to control the shrinkage rate of the final mold Conseqently, the shrinkage rate was under 0.1% through that process. The mechanical characteristic was also excellent. Generally, in the slurry casting, the alumina powder and the water soluble phenol were mainly used. However, the mechanical property of the phenol was not good enough to apply to molds directly. In this study, aluminium powder filled with epoxy is applicated to the slurry casting to solve these problems. The mechanical and thermal properties are better than phenol because the epoxy is the thermosetting resin. We achieved a successful result that the shrinkage rate is shortened about 0.047%. Futhermore, the manufacturing time and cost savings are significant. Finally, we assume that the developing possibility of this process is very optimistic.

• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.260-268
• /
• 2000

응고 및 마모거동을 연구하기 위하여 Cr, V, Mo 및 W의 조성이 다른 3종류의 백주철을 주조하였다. 고주파유도용해로에서 장입시켜 1873K까지 승온시켜 장입원료들을 모두 용해시킨 후 1823K에서 Y블럭주형에 주입하였다. 얻어진 3종류의 백주철조성은 다음과 같다: Fe-3%C-10%Cr-5%Mo-5%W(합금1), Fe-3%C-10%V-5%Mo-5%W(합금2) 및 Fe-3%C-17%Cr-3%V(합금 3)응고과정을 추적하기 위하여 각 시편으로부터 50g을 채취한 후 알루미나도가니에 넣고 실리콘카바이드로를 사용하여 1723K의 알콘분위기하에서 재용해를 시켰다. 용금을 10K/분의 속도로 냉각시키면서 열분석을 행하였으며 도중 몇 차례 소입 실험을 병행하였다.합금1의 경우 초정오스테나이트, (오스테나이트+$M_7C_3$)공정, (오스테나이트+$M_6C$)공정, 합금2의 경우 초정 MC, 초정오스테나이트, (오스테나이트+MC)공정 , (오스테나이트+$M_2C$)공정, 합금3의 경우 초정 $M7C_3$와 (오스테나이트+$M_7C_3$)공정으로 구성되어 있었다. 주방상태, 균질화열처러상태, 공냉상태, 템퍼링상태에서 내마모시험을 행하였다. 먼저 주방상태시 편을 진공분위기하에서 1223K에서 5시간동안 균질화열처리를 행한후 로냉을 시켰다. 다시 이 시편을 1323K에서 2시간 유지후 강제공냉을 시켰으며 강제공냉된 시편을 573K에서 3시간동안 템퍼링처리를 하였다. 내마모시험은 120 mesh마모지에 10N의 하중을 가하여 실시하였다. 각 사이클마다 무게감소를 측정하였으며 8번 반복실험을 하였다. 마모량은 균질화열처리시편, 주방상태시편, 템퍼링시편, 공냉시편의 순으로 감소하였다. 합금2가 마모량이 가장 적었으며 합금3이 가장 많았다. 합금2의 마모량이 가장 적은 이유는 조직이 초정 MC, 공정 MC 및 공정 M2C로 구성되어 있기 때문으로 사료된다.주방상태에서 기지조직은 퍼얼라이트이었으나 열처리를 통하여 마르텐사이트, 템퍼드마르텐사이트, 잔류오스테나이트로 변태하였다. 이상의 결과를 종합해 보면 MC가 내마모성에 가장 기여하는 조직으로 판단되어진다.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1165-1169
• /
• 1998

A single crystal cast blade was manufactured by CMSX 6, one of the first generarion nickel based single crystal superalloys by the selector method in a vacuum furnace. The single crystal has been grown with cooling rate of 2.5 mm/min, after pouring the molten alloy of 163$0^{\circ}C$ to the mold heated to 150$0^{\circ}C$. The cast structure could be classified into matrix (dendrite) and eutectic regions in ${\gamma}$'shape and size. The eutectic region showed higher Ti content. As the additional results of ${\gamma}$'precipitates by EPMA and CBED analysis the ${\gamma}$'size was less than 0.5~0.7$\mu\textrm{m}$, showing the chemical composition close to Ni$_3$Al of Ll$_2$ lattice structure. But ${\gamma}$'size has increased to bigger than 1.0$\mu\textrm{m}$, being near to eutectic region, changing its shape to bar or huge block types. These showed the chemical structure near to Ni$_3$Ti of D $O_{24}$ lattice structure. Therefore, ${\gamma}$'morphology of dendrite and eutectic regions depends absolutely on its chemical composition and lattice structure.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.409-414
• /
• 2000

Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their transformation behavior of matrix structures in heat-treated conditions. The specimens were produced using a 15kg-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides and matrix structures : 3%C-10%Cr-5%Mo-5%W(alloy No. 1), 3%C-10%V-5%Mo-5%W(alloy No. 2) and 3%C-17%Cr-3%V(alloy No. 3). The heat-treatments were conducted as follows: frist of all, as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. The observation of morphology of the matrix structures was carried out in the states of as-cast(AS), air-hardened(AHF) and tempered(AHFT). The matrix structures of each alloy were almost fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and retained austenite by the heat-treatments such as air-hardening and tempering.

• KSBB Journal
• /
• v.13 no.6
• /
• pp.706-717
• /
• 1998

Enzymatic synthesis of fructose-based sugar fatty acid esters, such as methyl fructoside oleic acid mono and diester, was investigated using methyl fructoside as a sugar starting material. For the production of methyl fructoside fatty acid monoester by solvent process, 2-methyl 2-propanol was found to be a god reaction medium resulting a higher yield and productivity due to its high sugar solubility. The yield and productivity of methyl fructoside oleic acid monoester were 70% and 12.6g/L-hr, respectively, when molar ratio of methyl fructoside, initial concentration of methyl fructoside, enzyme(Novozym 435) content, and reaction temperature were 3:1, 200g/L, 1%(w/v), and $60^{\circ}C$, respectively. Methyl fructoside oleic acid diester was prepared by lipase-catalyzed diacylation of methyl fructoside and oleic acid in the solvent-free process. Maximum yield of 98% and productivity of 140g/L-hr were achieved when molar ratio(methyl fructoside and oleic acid) of 1:2 enzyme content of 10%(w/v) and reaction temperature of $70^{\circ}C$ were applied for the operating conditions under a reduced pressure of 20∼200 mmHg.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.2
• /
• pp.99-107
• /
• 1998

This dissertationhas confirmed the non-flam mability of cast mold transformer that is increasingly used lately. As a research progress, the investigation has been performed on the installation status and each line of the subway system which have the most mold transformer accidents, and the impediment status of the transformer for rectifier and the high-voltage distribution transformer per each manufacturer. Then, a high voltage mold of the actual mold transformer has been installed in the horiwntal heating furnace and the heat has been applied by the standard heating temperature curve of KSF 2257(Fireproof testing meth od of the construction structures: 1993). Accordingly, the combustibility of the mold transformer based on the test results has been found that 78 minutes has been required for the complete burning per the KSF 2257 combustion test curve and that, after stopping the heat application of the horizontal furnace after ignition, the flame progress has not been made but shown as the self-extinguishing characteristics when the flame progress has been checked. Thus, the non-flammability and self-extinguishability of the mold transformer have been confirmed. The result of this dissertation has indicated that the accident involving mold transformer has been progressed and expanded by the dielectric breakdown or void due to the crack in the mold rather than a fire accident caused by a short-circuit or an overload.r an overload.