• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.31-37
• /
• 2011

직조 금속 스크린 리브(rib) 이 바닥에 설치된 사각 덕트에서 열전달과 유체유동의 압력강하를 측정하기 위해 실험적 연구를 수행하였다. 시험부의 치수는 200 mm(W) ${\times}$ 40 mm(H) ${\times}$ 712 mm(L)이고 수력직경은 66.6 mm이다. 입구영역에는 1.72m 길이의 가열되지 않은 동일한 치수의 채널을 설치하였다. 메쉬가 다른 4가지의 직조금속 스크린 리브에 대해 측정하였다. 그리고 비교를 위해 일체형 리브에 대해서도 측정하였다. 국부 열전달 계수의 측정에는 스테인레스 강제 포일(foil) 히터와 T형 열전대률 이용하였다. 레이놀즈 수는 23,000에서 58,000의 범위이다. 덕트의 수력직경($D_h$)에 대한 직조 금속 리브의 높이(e)의 비($e/D_h$)는 0.075 이고 리브 간격(p)과 높이의 비(p/e)는 10이다. 실험 결과 메쉬가 없는 일체형 리입에서 가장 누셀트 수와 마찰계수가 컷다.

• The Korean Journal of Rheology
• /
• v.5 no.1
• /
• pp.85-92
• /
• 1993

수지이동 성형공정에서 수지가 섬유직조망에 함침될 때의 투과계수와 수지의 표면 장력으로 인하여 유동진전면에서 발생하는 모세관압을 실험적으로 측정하였다. 두 종류의 섬유조직망에 대해서 가공율이 증가함에 따라투과계수는 증가한다. 수지, 섬유 그리고 공기 가 서로 다른 세 개의 상을 구성함으로써 수지의 표면장력의 영향을 받는 비정상상태의 투 과계수가 수지의 섬유직조망에 포화된 정상상태에서 측정된 투과계수보다 본 실험에서 수행 된 모든 기공을 범위에서 크다는 것을 보여주었다. 수지 유동진전면에서 발생되는 모세관압 은 기공율이 감소함에 따라 증가하였고 섬유직 조망의 기공율이 0.469인 경우에는 금형입구 에서의 수지주입압력의 25%에 해당되는 모세관압이 발생되는 것으로 나타났다. 따라서 모 세관압을 가공조건으로 고려해다 한다는 것을 제시할수 있었다. 또한 본연구에서 사용된 임 의 배향 섬유직조망에 대해 실리콘 오일과 유리섬유 계면의 동적접촉각 측정을 통하여 섬유 배향 및 기공의 분포를 나타내는 형상인자의 값을 구함으로써 실제 RTM 공정에서 발생되 는 모세관압을 예측할 수 dLT는 기초자료를 제시하였다.

• Journal of the Korean Home Economics Association
• /
• v.23 no.1
• /
• pp.1-9
• /
• 1985

과테말라의 알타 베라파즈 지역에서 원주민들의 민속의상의 하나인 Huipil 재료로 생산되는 반투명의 백생 무명 수직물은 독특한 직조기법과 구성을 보이고 있다. 이에 대한 부분적인 연구는 O'neale 과 Osborne 등에 의하여 이루어 졌으며, 본고에서는 이들 연구를 기초로 이 지역의 Huipil 재료의 직조과정과 기법에 대하여 고찰하였다. 또한 구체적인 직물구조의 분석은 Iowa 주립대학의 직물소장품중 4점의 이지역 Huipil 재료를 실측하여 이들 각각의 전체적인 구조와 기본적인 직조방법, 그리고 무늬를 형상하는 기법에 대하여 검토하엿다. 본 고찰을 통하여 이 지역에서 생산된 Huipil은 대부분 원시적인 형태의 직조기에 의해 완성되었으며 복잡한 무늬를 짤 경우에도 보조적인 도구는 사용되지 않고 특유의 수직기법에 의해 이루어졌음을 밝혓다. 또한 Huipil의 바탕은 plain weave, gauze, 도는 brocade의 변형으로 구성되었으며 바탕과 무늬의 변화는 실의 굵기의 변화로 더욱 강조되어 독특한 효과를 나타내고 있다.

• Composites Research
• /
• v.16 no.2
• /
• pp.33-40
• /
• 2003

In order to overcome one of the most pronounced shortcomings of conventional laminated composites, such as the low damage tolerance due to delamination, the thermoplastic materials and 3D (three-dimensional) preforms have been utilized in the manufacture of composite materials. From the newly developed process termed as the co-braiding, hybrid yarns of the thermoplastic fibers (PEEK) and reinforcing fibers (carbon) have been fabricated. In order to further enhance the delamination suppression, through thickness fibers have been introduced by way of 3D weaving technique in the fabrication of textile preforms. The preforms have been thermoformed to make composite materials. Complete impregnation of the PEEK into the carbon fiber bundles has been confirmed. For the comparison of mechanical performance of 3D woven composites, quasi-isotropic laminates using APC-2/AS4 tapes have been fabricated. Tensile and compressive properties of both the composites have been determined. Furthermore. the open hole, impact and CAI(Compression After Impact) tests were also carried out to assess the applicability of 3D woven textile reinforced thermoplastic composites in aerospace structures.

• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.339-348
• /
• 1994

The study has been conducted to know ablation microstructures and characteristics in carbon /phenolic composites. Ablation properties depend on mole fraction of $H_2O$ and $C0_2$ gas which were produced by reaction between propellant and oxidizer. However, the results of this study shown that the ablation also depended on weaving structure, density of fabric, and tow size of carbon fiber. 3K 8HS fabric showed superior ablation resistance to others, 3K twill and 12K 8HS fabric structures.

• Composites Research
• /
• v.14 no.6
• /
• pp.38-46
• /
• 2001

In this study, An optimization code that can design microwave absorbing composite laminates is developed, and 3-layered microwave absorbing composite laminates are developed by optimizing the thickness of each layer. The layers are 3 different composite laminates. Many variables including lay-up angles of electromagnetically orthotropic composite layer can be considered in this code. The developed laminate is composed of an impedance matching layer of glass/epoxy fabric laminate, a glass/epoxy fabric laminate layer containing aluminum filler and carbon/epoxy fabric laminate layer. Permittivities of the materials are obtained using a network analyzer and a coaxial air line.

• Journal of Bio-Environment Control
• /
• v.10 no.3
• /
• pp.181-186
• /
• 2001

During the growth of fruit vegetables such as pepper, cucumber and tomato, there are light deficiency under the plant canopy. This study was conducted to clarify the effect of light diffusion film on the stem growth, canopy, flowering and fruiting of green pepper in greenhouse. The transmittance of total solar radiation into greenhouse under woven and double films were 90% and 75% of polyethylene film. And the transmittance of photosynthetically active radiation into greenhouse under woven and double films were 96% and 81% of polyethylene film. However, the light diffusions under woven, double and polyethylene films were 46%, 31% and 9%, respectively. The plant height under polyethylene film covered greenhouse was 96.9% cm, taller than those under woven and double films by 6.5, 13.9 cm. And the third node length under woven film covered greenhouse was 8.6 cm, shorter than those under double and polyethylene films by 2.5, 5.7 cm. Also the first branch angle under woven film covered greenhouse was 61.0$^{\circ}$, larger than those under double and polyethylene films by 2.3, 10.3$^{\circ}$. But there was no clear difference in the node numbers among the covering materials. The rate of curved and sterile fruit under woven film covered greenhouse was smaller than those under double and polyethylene films by 4.6, 5.5% and 1.2, 3.6%. But the contents of vitamin C showed no difference among the covering materials and plant densities.

• Composites Research
• /
• v.32 no.1
• /
• pp.65-70
• /
• 2019

The aircraft composites wing parts are usually integrated with adhesive or fastener. These laminated composites have weak interlaminar strength, which can lead to delamination. In order to compensate the disadvantages of laminated composites, it is possible to improve the strength, durability, shock and fatigue resistance by reinforcing the fiber in the thickness direction. In addition, using a single structure near-net-shape saves the manufacturing time and the number of fasteners, thus can reduce the overall cost of the composite parts. In this study, compression test, tensile test and open-hole tensile test are carried out for three structural architecture of 3D (three-dimensional) textile preforms: orthogonal(ORT), layer-to-layer(LTL) and through-the-thickness(TTT) patterns. Among these, the orthogonal textile composite shows the highest Young's modulus and strength in tensile and compression. The notch sensitivity of the orthogonal textile composite was the smallest as compared with UD (unidirectional) and 2D (two-dimensional) fabric laminates.

• Composites Research
• /
• v.35 no.4
• /
• pp.269-276
• /
• 2022

In this paper, a composite stiffened panel was fabricated using a three-dimensional weaving method that can reduce the risk of delamination, and mechanical properties such as buckling load and natural frequency were investigated. The preform of the stringer and skin of the stiffened panel were fabricated in one piece using T800 grade carbon fiber and then, resin (EP2400) was injected into the preform. The compression test and natural frequency measurement were performed for the stiffened panel, and the results were compared with the finite element analyses. In order to compare the performance of 3D weaving structures, the stiffened panels with the same configuration were fabricated using UD and 2D plain weave (fabric) prepregs. Compared to the tested buckling load of the 3D woven panel, the buckling loads of the stiffened panels of UD prepreg and 2D plain weave exhibited +20% and -3% differences, respectively. From this study, it was confirmed that the buckling load of the stiffened panel manufactured by 3D weaving method was lower than that of the UD prepreg panel, but showed a slightly higher value than that of the 2D plain weave panel.

• Composites Research
• /
• v.12 no.2
• /
• pp.70-81
• /
• 1999

Resin transfer molding(RTM) as a composite manufacturing process is currently of great interest in the aerospace industry requiring high performance composite parts. In this study, an analysis of mold filling in the RTM process was carried out by numerical simulation using finite element/control volume technique. Experimental work for the visualization of resin flow through fibrous preform was also conducted in order to quantitatively measure the permeabilities of the fiber mats and to evaluate the validity of the developed numerical code. The different types of fiber mats and silicon oils were selected as reinforcements and resin materials, respectively. The effects of fibrous preform structure, mold geometry, and preplaced insert on the flow front patterns during mold filling were examined by integrating the model predictions and experimental results. The flow fronts predicted by numerical simulation were in good agreement with those observed experimentally. However, according to the regions of the mold, some deviations between predicted and observed flow fronts could be found because of non-uniform fiber volume fraction. Weldline locations for the resin flow through round insert preplaced in the mold could be qualitatively deduced based on predicted flow fronts.