• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.9
• /
• pp.874-883
• /
• 2008

This study considers powered explicit guidance, one of the closed-loop guidance laws for satellite launch vehicles. The guidance algorithm employed here does not include the iterative procedure of the original algorithm. Also, the single-target algorithm to treat the general time-varying thrust profiles is described. The computer simulations for the 6-DOF launch vehicle model are performed to investigate the orbit injection accuracy of the guidance algorithm in the nominal/off-nominal flight conditions.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.353-358
• /
• 2000

To achieve the requirement for high fuel economy and low emissions, the research for GDI engines is recently very brisk in the whole world. This study was performed to measure distribution of average particle size in non-evaporating spray. The 2-D fluorescence/scattering images of fuel spray were captured simultaneously by visualization system composed of a laser sheet, a doubling prism, optical filters, and an ICCD camera. Using the ratio of the two light intensities, particle size distribution was obtained. The SMD measured by fluorescence/scattering technique was compared with it obtained by PDA. The experimental results show that the spray structure of GDI injector and temporal SMD distribution.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.829-834
• /
• 1995

최근 전세계적으로 활발히 연구가 진행되고 있는 저준위 방사성폐기물 유리화에 관한 타당성을 조사하기 위해 여러 형태의 유리용융로에 대한 기술성을 분석하고, 기술성 분석에서 선택한 용융로를 이용한 3종류의 새로운 처리개념에 대한 경제성 분석을 수행하였다. 기술성 분석 대상 용융로는 프랑스 CEA/SGN 사의 직접유도가열식 저온로, 미국 VECTRA 사의 수직전극가열식 저온로, 미국 SEG사의 용응금속로 미국 Retech 사의 플라즈마토치 용융로이다. 기술성 분석결과 직접유도가 열식 저온로와 플라즈마토치 용융로를 병행하여 적용하는 것이 바람직하다는 결론을 얻었다. 이 용융로들을 이용한 3종류의 처리개념에 대해 처분부피, 처분단가에 따른 처분비, 처리비를 산정하고 현재 적용하고 있는 처리개념과 상호 비교하였다. 비교 결과 유리화 기술을 적용하는 것이 경제적이라 것과 현재 보다 80 %이상 처분부피를 감소시킬 수 있다는 것을 알 수 있었다.

• Journal of Power System Engineering
• /
• v.11 no.4
• /
• pp.18-25
• /
• 2007

제 2세대 직접분사식 가솔린 기관에서 6공 연료분사기의 연료분무특성을 관찰하였다. 실험에 사용한 직접분사식 가솔린 기관은 2개의 흡입밸브와 2개의 배기밸브를 갖는 텀블형 Spray Guided 연소실과 Quartz로 제작된 실린더 라이너와 실린더 헤드 창으로 구성되어 있다. 선회유동을 유도하기 위하여 흡입매니폴드에 선회유동 제어밸브를 부착하였다. 2차원 Mie 스캐터링 기법을 이용하여 연료분사시기, 연료분사압력과 실린더 내 유동 및 냉각수 온도가 연료분무에 미치는 영향을 관찰하였다. 실험결과로는 흡기과정동안 흡기 선회유동은 분사된 연료의 공간적 분포에 크게 작용하였고, 압축과정동안에는 텀블 및 선회유동의 영향이 흡기과정에 비해 크지 않음을 확인하였다. 또한 성층연소를 위해서 압축과정에서 연료를 분사하는 경우 고압의 연료분사압은 분무도달거리의 성장을 촉진시키나 상승하는 피스톤과 이로 인한 실린더 압력의 상승으로 분무도달거리의 성장이 억제됨을 확인할 수 있었다.

• Korean Journal of Food Science and Technology
• /
• v.24 no.4
• /
• pp.393-395
• /
• 1992

The ${\alpha}-lactalbumin({\alpha}-la)$ concentration in raw and laboratory-heated milks by HPLC was 1.20 mg/ml (unheated), 1.17 mg/ml ($63^{\circ}C$, 30min), 1.13 mg/ml ($72^{\circ}C$, 15sec) and 0 mg/ml ($100^{\circ}C$, 10min), respectively. Whereas, ${\alpha}-lactalbumin$ concentration ranges of commercial milks were $1.00{\sim}1.02\;mg/ml$ (pasteurized), $0.23{\sim}0.68\;mg/ml$ (UHT-pasteurized) and $0.77{\sim}0.89\;mg/ml$ (UHT-sterilized), respectively. It was supposed that the ${\alpha}-lactalbumin$ content of sterilized milk will be lower than that of UHT milk, but the opposite occurred. This discrepancy would be caused by the different heating system in the milk plants, where indirect UHT-treatment had more heat intensity than direct UHT-processing. The HPLC determination of ${\alpha}-lactalbumin$ may be an indicator to evaluate correctly and rapidly heated milks.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.273-273
• /
• 2018

하천유량을 산정하는 전통적인 방법은 수위-유량관계(stage-discharge relation)를 이용하는 것이며, 최근에는 하천특성에 따라 연속적으로 유속을 직접 측정하고 지표유속법(index velocity method) 또는 유속분포법(velocity profile method)을 이용하는 방법도 적용되고 있다. 연속으로 유속을 측정하는 방법에는 전자파 또는 영상이미지를 이용하여 표면유속을 측정하는 방법과 수중에 초음파 유속계를 설치하여 수중의 유속을 측정하는 방법이 있으며, 국내에서는 초음파 유속계를 이용하는 방법이 주로 활용되고 있다. 본 연구에서는 전자파표면유속계(MU2720)로 측정된 표면유속과 지표유속법을 이용하여 하천유량 산정방법을 검토하였다. 본 연구는 홍천강의 홍천군(반곡교)와 홍천군(홍천교), 한탄강의 철원군(한탄대교) 수위관측소에서 2016년도에 전자파표면유속계로 측정된 43개의 자료(평균유속 0.61~2.56m/s)를 이용하였다. 전자파표면유속계에 의한 유속측정은 한 지점에 고정하여 측정하지 않고 여러 개의 측선을 분할하여 표면유속을 측정하였으며, 단면 평균유속(Vm)과 가장 상관성이 높은 측선(지점)의 유속을 지표유속으로 하여 지표유속(vi)과 평균유속과의 관계식을 작성하고, 이를 통해 유량을 산정하였다. 여기서 평균유속은 전자파표면유속계로 측정한 유속을 이용하여 산정한 값이다. 그 결과 지표유속과 평균유속관계식의 결정계수($R^2$)는 0.9874~0.9976이었으며, 측정 평균유속과 지표유속관계식으로 산정된 평균유속과의 평균 편차율은 2.26~3.80%로 표면유속과 지표유속법을 이용한 유량산정 방법의 적정성을 확인할 수 있었다. 따라서 현재 국내에서 자동유량측정시스템에 초음파유속계만 상용화되고 있으나 향후에는 하천특성에 따라 전자파표면유속계를 이용하는 방법도 고려해 볼 필요가 있을 것으로 판단된다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.7-13
• /
• 2003

The purpose of this study is to investigate the effect of the in-cylinder flows and different injection timings on fuel behavior in the cylinder of a GDI engine. Three different flows types induced by using masked port, unmasked port, and port deactivation were tumble, swirl&tumble, and high swirl respectively. LIEF technique was applied to investigate the mixture formation and fuel distribution at ignition time in the transparent engine with optical access through the piston top and upper part of cylinder liner. Injection timings of 180,90, and 60 degrees before TDC were examined. It was found that tumble flow was more effective on the homogeneous mixture formation than other flow and swirl flow transported more fuel vapor to the exhaust side at early injection mode, and swirl and swirl & tumble flow made fuel vapor concentrate around the cylinder center at late injection mode.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.335-342
• /
• 2012

Nowadays, automobile manufacturers are focusing on the reduction of exhaust-gas emissions because of the harmful effects on humans and the environment, such as global warming by greenhouse gases. Gasoline direct injection (GDI) combustion is a promising technology that can improve fuel economy significantly compared to conventional port fuel injection (PFI) gasoline engines. In the present study, ultra-lean combustion with an excess air ratio of over 2.0 is realized with a spray-guided-type GDI combustion system, so that the fuel consumption is improved by about 13%. The level of exhaust-gas emissions and the operation performance with the multiple injection strategy and exhaust-gas recirculation (EGR) are examined in comparison with the emission regulations and from the point of view of commercialization.

• Journal of Korea Water Resources Association
• /
• v.47 no.9
• /
• pp.743-752
• /
• 2014

Delay time for groundwater recharge means the travel time from the bottom of soil layer to groundwater through vadose zone after infiltration from rainfall. As it is difficult to measure delay time, we suggested an empirical formula which is derived by using linear regression between altitude and delay time. For the regression analysis, 4 major gauging watersheds were chosen (Hancheon, Kangjeongcheon, Oedocheon, Cheonmicheon) with 18 measured groundwater level stations. To verify this empirical formula, derived equation from linear reservoir theory was applied to compute delay time and to compare estimated amounts of groundwater recharge using both methods. The result showed good agreement. Furthermore, if derived empirical formula would be linked with SWAT model, the spatial time delay effect in the watershed could be reflected properly.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.393-401
• /
• 2021

In this paper, we proposed a numerical model based on moment-curvature, to evaluate the resistance of reinforced concrete (RC) members subjected to blast loading. To consider the direct shear failure mode, we introduced a dimensionless spring element based on the empirical direct shear stress-slip relation. Based on the dynamic increase factor equations for materials, new dynamic increase factor equations were constructed in terms of the curvature rate for the section which could be directly applied to the moment-curvature relation. Additionally, equivalent bending stiffness was introduced in the plastic hinge region to consider the effect of bond-slip. To verify the validity of the proposed model, a comparative study was conducted against the experimental results, and the superiority of this numerical model was confirmed through comparison with the analytical results of the single-degree of freedom model. Pressure-impulse (P-I) diagrams were produced to evaluate the resistance of members against bending failure and direct shear failure, and additional parametric studies were conducted.