• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.221-228
• /
• 2013

An experimental study was carried out to investigate the effects of the injection timing on the spray and combustion characteristics in a spray-guided direct-injection spark-ignition (DISI) engine under lean stratified operation. An in-cylinder pressure analysis, exhaust emissions measurement, and visualization of the spray and combustion were employed in this study. The combustion in a stratified DISI engine was found to have both lean premixed and diffusion controlled flame combustion characteristics. The injection timing condition corresponding to the stratified mixture characteristics was verified to be a dominant factor for these flame characteristics. For the early injection timing, a non-luminous blue flame and low combustion efficiency were observed as a result of the lean homogeneous mixture formation. On the other hand, a luminous sooting flame was shown at the late injection timing because of an under-mixed mixture formation. In addition, the smoke emission and incomplete combustion products were increased at the late injection timing as a result of the increased locally rich area. On the other hand, the NOx emissions decreased and IMEP increased as the injection timing retarded. The combustion phasing produced by the injection timing was verified as the reason for this observation.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.18-23
• /
• 2004

Recently many researchers have been studying the development of alternative energy due to serious environmental pollution and drying up fossil energy. Among various alternative fuels, authors investigated the physical and combustion characteristics of the bio diesel fuel(BDF) which was made from the wasted vegetable oil. In this study, PXI and LabVIEW, which is a novel measuring instrument and online analysis, was used to investigate the combustion characteristics of BDF in a DI diesel engine.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.353-358
• /
• 2000

To achieve the requirement for high fuel economy and low emissions, the research for GDI engines is recently very brisk in the whole world. This study was performed to measure distribution of average particle size in non-evaporating spray. The 2-D fluorescence/scattering images of fuel spray were captured simultaneously by visualization system composed of a laser sheet, a doubling prism, optical filters, and an ICCD camera. Using the ratio of the two light intensities, particle size distribution was obtained. The SMD measured by fluorescence/scattering technique was compared with it obtained by PDA. The experimental results show that the spray structure of GDI injector and temporal SMD distribution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.22-30
• /
• 1999

Optimization of in-cylinder flow is regarded as one of the most important factors to realize stable stratified charge combustion in a Spark-ignited Direct Injection(SDI) engine. Therefore, Computational Fluid Dynamic(CFD) simulation technique were used to clarify the characteristics of in-cylinder flow of a SDI engine with top entry intake port. Also, CFD results were compared to experimental results using Laser Doppler Velocimetry(LDV), Particle Image Velocimetry(PIV) and good validations were met. As the results reverse tumble flow generated during intake process was preserved by configuration of curved piston while base and reverse tumbles were diminished at the end of compression stroke in case of flat top piston. In addition, it will be needed to optimize the fuel mixture distribution based on these results.

• Journal of ILASS-Korea
• /
• v.7 no.3
• /
• pp.1-6
• /
• 2002

In this study numerical and experimental study on the spray atomization characteristics of a GDI injector is performed. To carry out numerical analysis, four hybrid models that are composed of conical sheet disintegration model, LISA model, DDB model, and RT model are used. The experimental results to evaluate the prediction accuracy of hybrid models are obtained by using phase Doppler particle analyzer and spray visualization system. It is shown that the prediction accuracy of hybrid model concerning spray developing process and spray tip penetration is good for all hybrid models, but the hybrid breakup models show different prediction of accuracy in the case of local radial SMD distribution.

• Journal of ILASS-Korea
• /
• v.26 no.4
• /
• pp.197-203
• /
• 2021

In gasoline direct injection injectors, cavitation can be generated inside the hole because of their high injection pressure. In this paper, the effects of cavitation development in injector were investigated depending on the various hole drilling angles were investigated by a numerical method. In order to verify the internal flow model, injection rate and injection quantity of individual holes were measured. The BOSCH long tube method was used to measure the injection rate. As a result, even if the hole diameters were the same, the discharge coefficient differed by up to 10% depending on the hole angle. Moreover, if the hole drilling angle became greater than 30°, the area coefficient and the discharge coefficient decreased as the nozzle outlet was blocked due to cavitation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.134-139
• /
• 2008

This research investigated variations of the engine performance and the exhaust emission characteristic of a direct injection diesel engine by fueling a commercial diesel fuel, which was blended with the di-ether group (butyl-ether: BE). The smoke emission reduced to 26% from the diesel engine with the blending fuel (diesel fuel 80 vol-% + BE 20 vol-%)at the full engine load of 2500 rpm compared to it with the diesel fuel only. The power, torque and brake specific energy consumption of the diesel engine showed very slight differences. The NOx emission from the diesel engine, however, with the blended fuel was higher than with the commercial diesel fuel only. By applying EGR method, as a counter plan of the NOx reduction, this research obtained reductions of the smoke and NOx emission at the same time from the diesel engine with the BE blended diesel fuel.

• Journal of ILASS-Korea
• /
• v.12 no.4
• /
• pp.211-219
• /
• 2007

The liquid film thickness inside a pressure-swirl nozzle was measured, and then the measured liquid film thickness was compared with the results from previous empirical equations. The liquid film inside the nozzle was visualized using extended transparent nozzles and a microscopic imaging system, and then the measurement error was evaluated using optical geometry analysis. The high injection pressures up to 7MPa were adopted to simulate the injection conditions of the direct-injection spark-ignition engines. The totally different two injectors with different fuels, nozzle lengths, nozzle diameters and swirlers were utilized to obtain the comprehensive equations. The results showed that the liquid film thickness very slightly decreased at high injection pressures and the empirical equations overestimated the effect of injection pressure. Most of empirical equations did not include the effect of nozzle length and swirler angle, although it caused significant change in liquid film thickness. A new empirical equation was suggested based on the experimental results with the effects of fuel properties, injection pressure, nozzle diameter, nozzle length and swirler angle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.878-883
• /
• 2008

The spray characteristics of a high pressure 6-hole injector were examined in a single cylinder optical direct injection spark ignition (DISI) engine. The effects of injection timing, in-cylinder charge motion, fuel injection pressure and coolant temperature were investigated using the 2-dimensional Mie scattering technique. It was confirmed that the in-cylinder charge motion played a major role in the fuel spray distribution during the induction stroke while the propagation of fuel spray was restrained during the compression stroke by the increasing pressure and the upward moving piston. In additions, it was confirmed that the liquid fuel droplets existing at the sprays edges were vaporized by the increase of the coolant temperature.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.80-86
• /
• 2002

A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozzle hole, diameters of an injection pipe, and injection timing in the fuel injection system. We have obtained the results that the fuel consumption ratio is reduced and NOx concentration is increased as the smaller diameter of injection nozz1e hole, the smaller diameter of injection pipe, and more advanced injection timing. They show that optimizing the factors of fuel injection system is significant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.