• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.25-33
• /
• 1998

The characteristics of evaporation heat transfer for the utilization of LNG cold energy was investigated experimentally using liquified nitrogen and a solution of ethylene-glycol and water under horizontal two-phase conditions in the small-scale equipment of a cryogenic heat exchange system. The inner tubes in the double pipe heat exchanger with 8 mm and 15 mm inner diameter and 6 m length were adopted as a smooth test tubes and enhanced tubes by means of wire-coil inserts. Heat transfer coefficients and Nusselt number for the test tube were calculated from measurements of temperatures, flowrates and pressures. The correlations in a power-law relationship of the Nusselt number, the Reynolds number and Prandtl number for heat transfer were proposed which can be available for design of cryogenic heat exchangers. The correlations showed heat transfer coefficients for the wire-coil inserts were much higher than those for the smooth tubes, increased by more than 2.5 ${\~}$ 5.5 times depending upon the equivalent Reynolds number. Form and length of cryogenic double pipe heat exchanger were proposed for applicable to the utilization of LNG cold energy.

• Microbiology and Biotechnology Letters
• /
• v.20 no.4
• /
• pp.451-458
• /
• 1992

Pervaporation which is capable of removing ethanol selectively was adopted to reduce the ethanol inhibition and in situ recovery of ethanol in ethanol fermentation, The composite membrane made of silicone and polysulfone was used to separate the ethanol selectively. The ethanol selectivity of the membrane was about 4 and the total flux was 300 g/m2 h at 301:: and 10 mmHg for 25 g/l of feed concentration. Saccharomyces cerevisiae entrapped within Ca-alginate gels was employed for ethanol fermentations in a fluidized-bed bioreactor. The pervaporation membrane unit and fluidized-bed bioreactor were combined into one system. The proposed model equations for the combined system showed good accordances with the experimental results. It was found from the simulation results that the ethanol concentration in the broth for the combined system was lower than that for the continuous fermentation system without a membrane unit. Ethanol productivity can be thus increased by employing the combined system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.370-370
• /
• 2011

I-III-IV2족의 Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 3단계(three-stage) 동시증발공정을 통하여 약 19.9%의 최고의 효율을 보유하고 있다. 3단계 공정에 있어 IV2족 Se의 증발 속도 또는 증착압력은 우선 배향성 제어 및 표면 미세구조 영향 등에 큰 영향을 미치는 것으로 알려져 있다. 본 연구에서는 CIGS 박막 합성을 위한 3단계 공정에서 각 단계별 Se 분압의 변화를 주어, 각 공정 단계에서 Se 분압의 변화가 CIGS 박막의 미세구조 및 셀 효율에 미치는 영향을 분석하였다. 3단계 공정에서 Cu, In, Ga 분압은 고정시키고, Se 분압의 크기 순서대로 1, 2, 3으로 변화시켜 CIGS 박막을 제조하였다. 이 박막의 미세구조, 특히, 우선 배향성, 표면의 기공, 결정성을 제어 하기 위하여 3단계 공정에서 1st stage 이후 Se 분압을 증가시키는 방법($3{\rightarrow}1$, $2{\rightarrow}1$)과 1st stage 이 후 Se 분압을 감소시키는 방법($1{\rightarrow}3$, $1{\rightarrow}2$)을 적용하여 비교하였다. 그 결과 3단계에서 1st stage 이후 Se 분압을 증가시킴으로써 (220)/(204)의 우선 배향성을 촉진시키며, 결정성을 개선하였고, 1st stage 이후 Se 분압을 감소시킴으로써 CIGS 박막 표면의 기공을 제거하고, 결정성을 향상시켰다. 이렇게 1st stage이 후 Se 분압을 증가시킴으로써 (220)/(204)의 우선 배향성의 촉진과 결정성 개선은 단락 전류(Jsc)를 증가시켰으며, 1st stage 이후 Se 분압을 감소시킴으로써 CIGS 박막 표면의 기공을 제거와 결정성 개선은 개방전압(Voc)의 증가효과를 가져왔다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.245-253
• /
• 2010

The present study shows some results of developing evaporative heat exchangers with mini-channels. Heat exchangers with three different water paths were manufactured and tested to compare performances of cooling and pressure drop. Among the three types of heat exchangers, Type 2 with full-etching was proved to be the best in the cooling performances for considered operating conditions, and thus it is recommended to adopt Type 2 for its simplicity of production and outstanding performance. However, Type 1 was shown to be better when it is operated at a high air inlet temperature condition. The developed evaporative heat exchanger will be installed in Environmental Control Systems(ECSs) for aerial vehicles, and it can be used effectively in case an ECS is not only limited in its weight and volume but also required to absorb heats without supplying water (or a coolant) for a certain period of time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1003-1010
• /
• 2013

In this study, a simulation program was developed, which predicts the performance of cold-air forced circulation type air cooled showcase. The showcase has an excellent display effect in addition to preserving the grocery. In the program, the compressor was analyzed using performance data supplied by the manufacturer and the capillary tube pressure drop was analyzed using a homogeneous model. The evaporator and condenser were analyzed by dividing the heat exchangers into small elements, where energy balance and appropriate heat transfer correlations were used. A showcase model with two 3/4 HP compressors, capillary tubes of 1.6 mm inner diameter, a fin-and-tube evaporator and condenser was tested, and the results are compared with the predicted values. It is shown that both evaporation and condensation temperatures are adequately predicted by the program.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.9
• /
• pp.761-772
• /
• 2015

Microfin tubes having an outside diameter (O.D.) of 7.0 mm are widely used in residential air conditioning systems and heat pumps. It is known that the mass fluxes for air conditioners and heat pumps under partial load conditions are several tens of $kg/m^2s$. However, literature surveys reveal that previous investigations were limited to mass flux over $100kg/m^2s$. In this study, we conduct R-410A evaporation heat-transfer tests at low mass fluxes ($50-250kg/m^2s$) using a 7.0 mm O.D. microfin tube. During the test, the saturation temperature was maintained at $8^{\circ}C$, and the heat flux was maintained at $4.0kW/m^2$. For comparison purposes, we also test a smooth tube with a 7.0 mm O.D. The results showed that the heat-transfer enhancement factor of the microfin tube increased as the mass flux decreased up to $150kg/m^2s$, which decreased as the mass flux further decreased. The reason for this was attributed to the change of the flow pattern from an annular flow to a stratified flow. Within the test range, the frictional pressure drops of the microfin tube were approximately the same as those of the smooth tube. We then compare experimental data obtained with the predictions obtained for the existing correlations.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.9-18
• /
• 2013

Two-phase vapor-liquid flows exist in many shell and tube heat exchangers such as condensers, evaporators, and nuclear steam generators. To understand the fluid dynamic forces acting on a structure subjected to a two-phase flow, it is essential to obtain detailed information about the characteristics of a two-phase flow. The characteristics of a two-phase flow and the flow parameters were introduced, and then, an experiment was performed to evaluate the pressure loss in the tube bundles and the fluid-dynamic force acting on the cylinder owing to the pressure distribution. A two-phase flow was pre-mixed at the entrance of the test section, and the experiments were undertaken using a normal triangular array of cylinders subjected to a two-phase cross-flow. The pressure loss along the flow direction in the tube bundles was measured to calculate the two-phase friction multiplier, and the multiplier was compared with the analytical value. Furthermore, the circular distributions of the pressure on the cylinders were measured. Based on the distribution and the fundamental theory of two-phase flow, the effects of the void fraction and mass flux per unit area on the pressure coefficient and the drag coefficient were evaluated. The drag coefficient was calculated by integrating the measured pressure on the tube by a numerical method. It was found that for low mass fluxes, the measured two-phase friction multipliers agree well with the analytical results, and good agreement for the effect of the void fraction on the drag coefficients, as calculated by the measured pressure distributions, is shown qualitatively, as compared to the existing experimental results.

• Journal of the Korean Institute of Gas
• /
• v.11 no.3
• /
• pp.1-6
• /
• 2007

The heat transfer coefficient and pressure drop during gas cooling process of $CO_2$ (R-744) in inclined helical coil copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube, which is specified as the inner diameter of 4.55 mm. The refrigerant mass fluxes were varied from 200 to $600kg/m^2s$ and the inlet pressures of gas cooler were done 7.5 to 10.0 (MPa). The heat transfer coefficients of $CO_2$ in the inclined helical coil tubes increase with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows relatively good coincidence with those predicted by Ito's correlation developed for single-phase in a helical coil tube. The local heat transfer coefficient of $CO_2$ is well coincident with the correlation by Pitla et al. However, at the region near pseudo-critical temperature, the experiments indicate higher values than the Pitla et al. correlation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.723-729
• /
• 2016

This study compared fin-tube and parallel-flow heat pipes for their sensible heat exchange rate, heat recovery amount, and air-side pressure drop. Tests were done with different refrigerant charging rates of 40-60% vol. and air flow rates of 300-1,400. The sensible heat exchange rate was highest for both types of heat pipes at a working fluid charge of 40% vol. and low flow rate. For the parallel-flow heat pipe, the 60% vol. charge is too high and results in a low sensible heat exchange rate. The reason is that the thicker liquid film of the tube wall deteriorates the heat transfer effect. Hence, the optimal charging rate is 40 to 50% vol. The evaporator heat pipe has a larger air-side pressure drop than the condenser section heat pipe. The reason is considered to be condensation water arising from the evaporator surface. Compared to the fin-tube heat pipe, the parallel-flow heat pipe showed better performance with a working fluid charging rate of 48%, volume of 41%, and an air-side pressure drop about 37%.

• Journal of the Korean Chemical Society
• /
• v.59 no.5
• /
• pp.454-465
• /
• 2015

The goal of this study is to investigate pre-service chemistry teachers’ understanding of the boiling process of a liquid mixture. We surveyed 65 students in the chemistry program of the College of Education about the boiling point of a 50%(by mole) ethanol aqueous solution and the temperature changes during heating. We then interviewed 9 of these students. According to the survey results, the percent of the pre-service teachers who thought that the boiling point of the ethanol solution would be ‘between the boiling points of ethanol and water (78-100 ℃)’ and ‘the same as that of ethanol’ were 52.3% and 35.4%, respectively. The majority of those who stated the former explained that the boiling point of the ethanol solution increased due to the effects of attraction or blocking by water molecules. Most of those who believed the latter explained that physical properties such as the boiling point would not be changed by the addition of water. With regard to the temperature change during heating, 69.2% of the teachers thought that the temperature would increase gradually while boiling, which some thought resulted from the increasing amount of water in the solution as the ethanol boiled off. Others thought that two temperature plateaus would be observed as each component of the liquid mixture underwent phase transition at its specific boiling point. When asked about the particle model of the gas phase during the boiling and evaporation process, some students drew both ethanol and water during evaporation but only ethanol when boiling. We discussed several alternative concepts of pre-service chemistry teachers about the boiling process of liquid mixtures and ways to improve their understanding.