• Journal of dental hygiene science
• /
• v.9 no.2
• /
• pp.189-195
• /
• 2009

Two diketones, 1,2-phenylpropanedione (PD) and diacetyl (DA) were investigated as new visible light photosensitizers for dental composite resin of bis-GMA in order to improve the photopolymerization effect. The photopolymerization efficiency of bis-GMA composite resin containing PD and DA was studied by IR absorption spectroscopy. And the results were compared with that of camphorquinone (CQ). Relative photopolymerization efficiency of the photosensitizers increased in the order of DA < CQ < PD. Thus. PO is a new visible light photosensitizer for dental composite resin with higher photopolymerization efficiency than that of CQ.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.4
• /
• pp.623-631
• /
• 2007

Effect of Soft-start curing on the contraction stress of composite resin restoration polymerized with LED and plasma curing unit The purpose of this study was to evaluate the influence of soft-start light curing on contraction stress and hardness of composite resin. Composite resin (Filtek $Z-250^{TM}$, 3M ESPE, USA) was cured using the one-step continuous curing method with three difference light sources ; conventional halogen light ($XL3000^{TM}$, 3M ESPE, USA) cure for 40 seconds at $400 mw/cm^2$, LED light (Elipar Freelight $2^{TM}$, 3M-ESPE, USA) cure for 20 seconds at $800\;mW/cm^2$ a and plasma arc light ($Flipo^{TM}$, LOKKI, France) cure for 12 seconds at $1300 mW/cm^2$. For the soft-start curing method ; LED light (Elipar Freelight $2^{TM}$, 3M-ESPE, USA) cure exponential increase with 5 seconds followed by 17 seconds at $800\;mW/cm^2$ and plasma arc light ($Flipo^{TM}$, LOKKI, France) cure 2 seconds light exposure at $650\;mW/cm^2$ followed by 11 seconds at $1300\;mW/cm^2$. The strain guage method was used for determination of polymerization contraction. Measurements were recorded at each 2 second for the total of 800 seconds including the periods of light application. Obtained data were analyzed statically using Repeated measures ANOVA, One way ANOVA, and Tukey test. The results of present study can be summarized as follows: 1. Composite resin restoration showed transient expansion just after irradiation of curing light. Contraction stress was increased rapidly at the early phase of polymerization and reduced slowly as time elapsed (P<0.05). 2. Contraction stress was not revealed significant difference between Halogen curing light groups and LED and Plasma Light curing with soft-start group (P>0.05). 3. LED and Plasma Light curing with soft-start showed lower contraction stress than the one-step continuous light curing (P<0.05).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.29 no.4
• /
• pp.592-599
• /
• 2002

Objective : The purpose of this study was to evaluate the effects of several light curing methods and several adhesives on the microleakage of composite resin restorations in primary teeth. Materials and methods : In 150 extracted human primary anterior teeth, O-shaped cavities were prepared in the labial surface ; the cavity diameter and depth were 1.6mm. The cavities were filled with light-activated composite resin, Compoglass. Four kinds of adhesives were used. Each filling materials were polymerized with three light cure methods. The restorations were polished using Sof-Lex discs(3M Co., USA). The samples were thermocycled 1,000 times between $5^{\circ}C$ and $55^{\circ}C$ with a 1-minute dwell time. Then, they were immersed in a 2% methylene blue solution(pH 7) for 12hours. Subsequently they were sectioned labio-lingually through the center of the restoration with a diamond saw at low speed with a water coolant, and evaluated by stereomicroscopy. Microleakage analyses were done, using scores from 0 to 4. Results : Results showed the least microleakage in Compoglass group(P<0.05). There were less microleakage in SBMP group among the adhesive groups, but no significant difference was observed(P>0.05). And there were no significant differences among the groups depending on curing methods(P>0.05).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.349-349
• /
• 2012

산화제를 이용 기상중합법을 통해 합성되는 고전도도 Poly (3,4-Ethylenedioxythiophene)(PEDOT) 박막은 OTFT, RFID tag, 또는 연성 디스플레이 같은 분야에 다양한 응용 가능성을 가지고 있으며 이로 인해 최근에 연구가 활발히 진행되고 있다. PEDOT박막의 전극소재로써 가능성은 박막의 중합 정도와 표면 형상에 크게 좌우된다. 특히, Si-웨이퍼 기판 위에 산화제의 균일한 도포 및 산화제 자체의 높은 산도 ($pH{\leq}2$)에 따른 부반응의 억제는 기상중합법을 이용한 PEDOT박막의 합성에 있어 매우 중요하다. PEDOT의 효율적인 중합과 균일한 성장을 위해 산화제에 DUDO 와 PEG-PPG-PEG를 첨가한 혼합 산화제 용액을 제조 기상중합 방법을 통해 PEDOT박막을 제작하였다. 그 결과 산화제만을 사용하여 제작된 박막에 비해 전도도가 최대 3,660 S/cm로 향상된 PEDOT 박막이 합성되었다. 이러한 결과는 PEG-PPG-PEG가 산화제 용액의 균일 도포를 향상시키고 Base Inhibitor로 작용하는 DUDO는 PEDOT 성장 시 중합속도를 조절하고 부반응을 최소화 하여 효율적인 공액 이중 결합의 생성을 촉진한데 주로 기인한다. 따라서 그로인해 조밀하며 마이크로 스케일의 기공이 최소화된 PEDOT박막의 합성이 가능하였다. PEDOT박막의 특성 평가에는 4-point probe, optical microscopy, Field Emission-Scanning Electron Microscope, 등이 사용되었으며 또한 전도도의 향상 원인을 분석하고자 ATR-IR Spectrophotometer를 이용하여 합성된 박막의 작용기를 분석하였다. 이러한 고전도도의 PEDOT 박막이 OTFT의 전극소재로 사용된다면 OTFT소자의 성능 향상에 크게 기여 할 것으로 기대된다.

• Economic and Environmental Geology
• /
• v.43 no.4
• /
• pp.349-358
• /
• 2010

For imaging complex subsurface structures such as salt dome, faults, thrust belt, and folds, seismic prestack reverse-time migration in depth domain is widely used, which is performed by the cross-correlation of shot-domain wavefield extrapolation with receiver-domain wavefield extrapolation. We apply the prestack reverse-time migration, which had been developed at KIGAM, to the seismic field data set of Block 5 in Jeju basin of Korea continental shelf in order to improve subsurface syncline stratigraphy image of the deep structures under the shot point 8km at the surface. We performed basic data processing for improving S/N ratio in the shot gathers, and constructed a velocity model from stack velocity which was calculated by the iterative velocity spectrum. The syncline structure of the stack image appears as disconnected interfaces due to the diffractions, but the result of the prestack migration shows that the syncline image is improved as seismic energy is concentrated on the geological interfaces.

• 대한치과보철학회:학술대회논문집
• /
• 2001.11a
• /
• pp.55-55
• /
• 2001

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.507-512
• /
• 2013

A graphene/waterborne polyurethane (WPU) nano composite was prepared by in-situ polymerization of PU and graphene having isocyanate (iGO) group in order to improve physicochemical/electrical characteristics. The properties of the graphene/WPU nanocomposite can effectively be enhanced as compared pristine WPU; up to 57% of tensile strength and $10^2$ fold of electrical conductivity with introduction of 2 wt% graphene. In addition, mechanical/electrical properties of the graphene/WPU nanocompsite were higher than those of graphene/WPU composite prepared by a simple physical blend method. It might attribute to homogeneous dispersion of iGO in the WPU matrix via covalent bonds and hydrogen bonds between WPU and iGO from the results of morphological analysis by scanning electron microscopy (SEM).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.1
• /
• pp.122-129
• /
• 2007

The purpose of this study was to evaluate the effects of a various light curing time on the residual monomers released from light-cured dental sealant, and to examine the effectiveness of surface treatment in reducing the oxygen-inhibited layer of light-cured dental sealant($Helioseal^{(R)}$ F, Vivadent, Liechtenstein). Specimens were cured with a halogen light curing unit(XL 3000, 3M, USA) for 20, 40, 60s. Surface treatment of a light-cured dental sealant included no treatment(control group), a 10-seconds exposure to distilled water(Group I), 10-seconds manual application using a cotton pellet wetted with 75% alcohol(Group II), and 10-seconds application of a water/pumice slurry using a rubber cup on a slow-speed handpiece The specimens were eluted in distilled water for 10 minutes. All elutes were analyzed by HPLC for identification and quantitive analysis of monomers. The results of this study can be summarized as follows. 1. None of the chromatograms of the tested sealant displayed peaks with the same retention time as that of the standard solution, except for TEGDMA. 2. The release of TEGDMA decreased with increasing curing time in conventional halogen light. 3. All surface treatment group had a decrease of monomer release in comparison with no treatment group. 4. Treatment that Group III eliminated the greatest amount of any type of residual monomers. 5. The elution of unreacted monomers from curing with halogen curing unit for 60s and Group III was less than other groups.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.2
• /
• pp.51-57
• /
• 1984

This studies have been carried out to find anticrease finishing method other than urea formaldehyde polymerization method which the author had done it with his former report. Acrylic amide polymerization method with water solubility controlling device was developed in this parer and the obtained results are as followings. 1. Poor anticrease silk textile could improve as much as 25% than original fabric. 2. Light density with high twisted silk textiles may improve a few per cent increase of anticrease, because they held good anticrease nature as well as polyester fabric. 3. There was no significant stiffness change after such finish. 4. This finish is recommended to carry after dyeing process either yarn dye or cloth dyeing. 5. The finished textile with this method is recommended to wash with dry cleanning method.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.450-453
• /
• 2010

The electrical/optical properties and surface structures of polypyrrole (PPy) thin films, which were prepared by liquid phase polymerization (LPP) and vapor phase polymerization (VPP) of pyrrole using FTS as an initiatior are compared. The PPy thin film prepared by VPP showed superior surface resistance characteristics as compared with that prepared by LPP. We investigated the relation between surface morphology of PPy film and surface resistance by surface characteristic analysis. The surface of PPy thin film prepared by VPP was smoother than that prepared by LPP. Micro-patterned PPy thin film could be prepared effectively using VPP-combined ink-jet printing and soft lithography.