• International Journal of Highway Engineering
• /
• v.8 no.1 s.27
• /
• pp.89-98
• /
• 2006

The weight-to-power ratio of the standard truck for the climbing lane design is known to be 200lb/hp. The value was known to be assumed based on constant trucks' capability and regional distributions in stead of widely varied distributions region by region. Additionally, this value was assumed after investigating registered vehicles' statistics instead of investigating real portions of truck volumes. Therefore, it may be said that the value of the current standard truck does not reflect regional or industrial diversity and proportions of truck volumes. To resolve these issues, the present paper studies diversified standard trucks which consider regionally or industrially diversified and observed-volume based weigh-to-power ratios. For this purpose, individual trucks' weigh-to-power ratios obtained at toll-gates of national expressways were used. For regionally based study, the whole nation are divided into 8 regions, then each region is characterized by a unit of a weigh-to-power ratio. The applicability of each value is provided. Results show that the single value for the nationwide standard truck may be 208 lb/hp, 8 lb/hp higher than the current value of 200 lb/hp. Results also show that regional values ranged widely from 170 lb/hp to 230 lb, 30 lb/hp higher/lower than the current value. Conclusively, regional diversity of trucks' weigh-to-power ratios was identified then three types of standardized weigh-to-power ratios which may represent regional characteristics were suggested. As the diversified standard truck are applied to the design standard, two benefits are expected such as decrease of rear-end accident rates or decrease of climb lane construction costs.

• Journal of Korean Society of Transportation
• /
• v.19 no.6
• /
• pp.119-129
• /
• 2001

본 연구는 국내의 화물차(이하 트럭) 특성, 도로 조건과 주행 저항이 고려된 트럭 성능 곡선 산출식의 매개변수를 추정하기 위하여 수행되었다. 이를 위해 국내 대표트럭을 선정하고 경사지 진입속도를 산출하였다. 국내 대표트럭의 선정은 자동차 등록현황 자료를 토대로 하여 트럭 중량/마력비에 대한 누적 분포를 작성하고 이 중에서 주요 차종(적재 중량 11톤 이상)의 총중량은 과적 검문소 자료로 보정하여 이루어졌다. 경사지 진입속도는 도별 평지부 직선 구간을 한 곳씩 선정하여 4차로도로와 2차로도로에서 수집되는 자료를 분석하여 산출하였다. 트럭 성능 곡선 산출식을 정립하기 위해 오르막 한계속도$(V_x)$ 산출식을 정리한 뒤 총중량(W), 엔진성능(P), 경사도(G)는 독려 변수로 k, $f_{rc}$, $f_{rv}$, $\Phi$는 매개변수로 설정하였다. 현장조사를 통해서 오르막 한계속도에 도달한 트럭의 총중량과 엔진성능, 속도, 경사도 등의 자료를 수집하여 매개변수 산출에 이용하였다. 마지막으로 추정된 매개변수를 이용하여 트럭 성능 곡선을 도출하였다.

• Journal of Korean Society of Transportation
• /
• v.25 no.5
• /
• pp.79-90
• /
• 2007

In determining vertical grades in highway alignment design, engineers usually consider heavy vehicle performances on the upgrade. Heavy vehicles usually experience speed reduction on the upgrade and with recent years weight/horsepower improvements for heavy vehicles the speed reduction shows some change. However, in spite of the weight to horsepower improvements for the design vehicles from 300lb/HP to 200lb/HP in the AASHTO, there was no change in the maximum vertical grades. Therefore, a review of the maximum vertical grade reflecting existing heavy vehicle performances is required. In particular, in South Korea where highways pass through lots of mountaineous terrain, the maximum vertical grades must be reviewed throughly. In this study the amount of heavy vehicle performances during past decades were investigated and their expected impacts on highway vertical alignment designs were subsequently analyzed. A worldwide terrain analysis and international design standards were compared to set South Korean vertical grade standards. Traffic flow simulation Vissim was utilized to simulate vehicular flows on the upgrade and new truck performance curves on the grades were developed. Based on the new curve, it was decided that $1{\sim}2%$ increase of the maximum vertical grades could be allowed.

• Journal of Korean Society of Transportation
• /
• v.24 no.5 s.91
• /
• pp.35-44
• /
• 2006

Acceleration and deceleration curves have been used for design purposes worldwide. The curve in design level has been regarded as an single deterministic curve to be used for design of climb lanes. It should be noted that the curve was originally made using ideal driving truck and that the curve is applied during design based on the assumption of no difference between ideal and real driving conditions. However. observations show that aged vehicles and lazy behavioring drivers nay make lower performance of vehicles than the ideal performance. The present paper provides the results of truck speeds at climbing lanes then probabilistic variation of acceleration and deceleration corves. For these purposes. a study about identification of vehicle makers, and weights for trucks at freeway toll gates and then observation of vehicle-following speed were performed. The 85%ile results obtained were compared with the deterministic performance curves of 180, 200, and 220 Ib/hp. It was identified that the performance of 85%ile results obtained from vehicle-following-speed observations were lower than one from deterministic performance curves. From these results, it may be concluded that at the beginning Point of climbing lanes additional $16.19{\sim}67.94m$ is necessary and that at the end point of climbing lanes $53.12{\sim}103.24m$ of extension is necessary.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1125-1126
• /
• 2011

고온 초전도 전력기기는 상전도 전력기기에 비해, 중량과 부피가 작고 전력손실이 거의 없어 효율이 높고 대용량기기에 많은 장점을 지니고 있으며 또한 환경 친화적이다. 대형화가 요구되는 선박추진용 모터를 초전도 모터로 사용할 경우 저속 및 고 토크의 모터를 제작할 수 있고, 계자 권선과 전기자 권선을 초전도 선재로 사용함으로써 높은 전류밀도와 고 자장이 가능하여 고효율 및 소형 경량화 등의 장점이 있다. 그러나 전초전도 모터의 경우 얇은 테이프 형태의 초전도 선재의 특성으로 인해 구리선처럼 가공이 힘들고, 선재를 초전도 상태로 만들기 위한 냉각이 필요하다. 이러한 문제점을 해결하기 위하여 본 연구에서는 동기모터와 선형모터를 혼합하여 고정자에 위치한 racetrack type의 전기자 권선뿐만아니라 회전자에 자기장을 발생시키는 계자 권선도 회전자가 아니라 고정자부분에 위치하므로 구조상 견고하고 냉각등에 장점이 있는 호모폴라 모터를 제안하였으며 자기저항의 변화가 작은 구조로 토크 리플이 작으므로 소음과 진동이 적은 모터를 설계하였다. 설계 결과로부터 호모폴라 모터를 제작하였으며 레이스트렉형과 팬케이크 권선의 임계전류등을 측정하였다. 추후 호모폴라 모터의 성능시험을 진행할 예정이다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.889-891
• /
• 2017

Usually piston or rotary engines are installed at UAV's under 100 kg payload class. Those engine are less expensive and easy to get, but they require higher operating and maintenance costs due to shorter life and unique fuel usage. They are also too noisy to operate in urban area and have too strong vibration to carry sophisticated payloads. On the contrary, a gas turbine engine has drawbacks like higher specific fuel consumption and weight to power ratio, even it has many operating and maintenance benefits. This study aims to design a small turboshaft engine with a recuperator to overcome those demerits. A tilt rotor UAV(TR-60) developed by KARI was chosen as an imaginary target aircraft, and engine power and size were derived from it. This paper describes engine requirements, design process, and initial reference point cycle design.