• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.593-604
• /
• 2007

Although composite construction has more mechanical advantages compared to noncomposite construction, the design of noncomposite construction for skew bridges with large skew angels has been often checked because composite construction may cause large stresses in the bridge deck. In this study, the analytical model considered dynamic behaviors for noncomposite skew bridges was proposed. Using the proposed analytical model, the validity of the application of noncomposite construction to skew bridges was checked. Also, the effects of interactions between the concrete deck and steel girders such as composite construction, partial composite construction, and noncomposite construction on the dynamic characteristics and dynamic behaviors of simply supported skew bridges were investigated. A series of parametric studies for the total 27 skew bridges was conducted with respect to parameters such as girder spacing, skew angle, and deck aspect ratio. Although the slip at the interfaces between the concrete deck and steel girders results in the reduction of seismic total base shear in the transverse direction due to period elongation, it causes an undesirable behavior of skew bridges by the modification in mode shapes and distributions of stiffness. Shear connectors placed by minimum requirements for partial composite action have an effect on reducing the girder stresses and deck stresses; except case of some skew bridges, the magnitude of the girder stresses and deck stresses obtained from partial composite skew bridges is similar to or slightly more than those acquired from composite skew bridges.

• Korean Journal of Veterinary Service
• /
• v.25 no.2
• /
• pp.153-174
• /
• 2002

파라믹소바이러스과 (Parnxouiridae) 바이러스는 외피당단백질의 생물학적 특성에 있어서 Orthomyxoviridae와, 분절되지 않은(nonseg-mented)게놈과 그 발현의 구성 측면에서 Rhbdoviridae와 유사성을 갖는 바이러스로서 외피로 둘러 싸여 있는 마이너스쇄(negative strand) RNA 바이러스이다. 마이너스쇄 RNA 바이러스의 게놈 RNA는 2가지 기능으로 작용한 다. 즉, 첫째는 mRNA 합성을 위한 주형(鑄型, template)으로 작용하고, 둘째는 플러스쇄 (anti-genome(+) strand)의 합성을 위한 주형으로서 작용한다. 마이너스쇄 RNA바이러스는 그들 자신의 RNA전사효소를 코드화 하여 저장하지만, mRNA는 감염세포 내에서 게놈이 노출된 후에만 합성된다. 바이러스 복제는 mRNA의 합성후 일어나며 연속된 바이러스단백질의 합성을 필요로 한다. 새로 합성된 플러스쇄(antigenome(+)strand)는 마이너스쇄 게놈 RNA의 복제를 도모하기 위한 주형(鑄型)으로서 작용한다.

• Applied Chemistry for Engineering
• /
• v.16 no.3
• /
• pp.408-412
• /
• 2005

Porous layered carbon was prepared by interlayer pyrolysis of pyrolysis fuel oil (PFO) using magadiite template and successive dissolution of template. Particle morphology was plate type with d-spacing of approximately 0.7 nm and it had constant interlayer space. Specific surface area was $147{\sim}385m^2/g$ depending upon template type, mixing ratios and pyrolysis time.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.2 s.72
• /
• pp.203-212
• /
• 2006

Although composite construction has many mechanical advantages over noncomposite construction, the design of noncomposite construction for skew bridges with large skew angels has been often checked because composite construction caused large stresses in the bridge deck. But there is somewhat difficulty to apply noncomposite construction in the field because of the structural problem such as the slip at the interface between the concrete deck and steel girders. In this study, the validity of the application of the composite construction to skew angles with large skew angles is investigated by analyzing effects of two interactions such as composite and noncomposite actions between the concrete deck and steel girders on the behavior of skew bridges. A series of parametric studies for the total 27 simply supported skew bridges was conducted with respect to parameters such as girder spacing, skew angle, and deck aspect ratio. The improvement of the behavior of composite skew bridges was examined by using the concept of the stiffness adjustment of bearings which I suggested in previous research. Results of analyses show that a more desirable behavior of skew bridges can be obtained from composite construction instead of noncomposite construction and the method of the stiffness adjustment of bearings results in a more rational and economical design of composite skew bridges and substructures.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.525-535
• /
• 1999

In this study, a new method of fabricated concrete deck bridge construction is proposed. This paper details the method in which concrete multi-girders and fabricated concrete decks are rested on the upper flange of the girder and the female to female type sheat-key is formed to connect girder and deck. The finite element analysis is performed to verify the accuracy of the structural behaviors of the fabricated concrete deck bridge by comparing with experimental results. The first task performed is the analysis of the equilibrium of the member force occurring between the deck and the girder. After verifying equilibrium of the member force determined by the finite element analysis, this process is applied to the analysis of maximum member force as the position of design load. This task is utilized to determine the safety of each member according to the same scale finite element model. The final process in this study is to compare the deflection of girders used in experiment with that of the same scale finite element model to verify the strength of fabricated cincrete deck bridge. By this comparison, it is shown that the behavior of the fabricated concrete deck bridge is almost same as the finite element analysis. The second task is to analyze the load distribution effect according to the number of diaphragms and the composite effect due to the cinnection of the deck and girder by the finite element analysis. From the results of second task, it is found that the load distribution effect is not related to the number of diaphragms in case of the central loading, but is related to the number of diaphragms for eccentric loading. Analysis of the load distribution indicates that the effective number of diaphragm is three. It is also shown that the maximum deflection is decreased to almost one half due to the composite action of the deck and girder.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.257-264
• /
• 2001

국내 고속철도 강합성 교량이 경부고속철도 8-2공구에서 처음으로 시공완료 되었다. 그동안 수년간에 걸쳐 고속철도 교량시공에도 불구하고 강합성 교량이 적용되지 못했던 것은 설계 기술적인 면과 더불어 재료 적인 면에서 국내여건이 성숙되지 못한 요인이 크다고 보여진다. 본 고에서는 기 설계된 PC BOX교량중 지형여건상 강합성교량이 적합한 교량구간을 제시하였다. 또한 강합성 교량의 설계기술적인면 중 특히 중요한 한국형 TGV차량의 동적 하중의 적용과 그에 따른 구조물 거동의 평가를 1＠50 교량에 대한 8-2공구 사례를 통하여 논의하였다. 강합성 단면은 단순 2주형 주형거더(double I beam)이며 플랜지 두께는 최대 80-100mm가 적용되어졌다. 본 단면에 대한 HL차량하중등에 대한 정적해석을 통하여 관심이 되고 있는 플랜지등의 응력 검토결과를 보여주었다. 아울러 정적해석과 동적해석의 결과치를 비교하여 국내 시방서에 제시된 고속철도 HL차량하중에 대한 평가도 이루어졌다. (중략)

• Journal of the Korean Chemical Society
• /
• v.52 no.5
• /
• pp.468-475
• /
• 2008

• Journal of the Korean Chemical Society
• /
• v.55 no.2
• /
• pp.317-322
• /
• 2011

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2702-2707
• /
• 2010

The load distribution factor (LDF) values of new composite I-beam panel bridges that were subjected to dead load were investigated using three-dimensional finite element analyses with the computer program ABAQUS(2007). This study considered some design parameters such as the slab thickness, the steel-plate thickness, and the span length for design of new composite bridges. The distribution values that were obtained from these analyses were compared with those from the AASHTO Standard, AASHTO LRFD, and the equations presented by Tarhini and Frederick, and Back and Shin. For the simple application of the design, bridge engineers can use the LDF of 0.67 for the exterior girder and of 0.340 for the interior girder.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.3A
• /
• pp.161-169
• /
• 2012

This paper presents the safety and strength of simplified composite H-beam panel bridges (SCHPBs) using 3-dimentional finite-element program, ABAQUS (2007) and experimental tests. Two finite-element models (one-steel-girder-and-composite-deck model and four-steel-girder-and-wide-composite-deck model) were reviewed to predict the strength and load distribution factor (LDF) values of the composite bridges. Based on the results of the finite-element analyses, the behaviors of the two models were investigated, and deflection and strain gauges for the experimental specimens were set up to obtain the ultimate strengths and the LDF values. The ultimate strength of the one-steel-girder-and-composite-deck specimen was estimated to be 840 kN. The yield and plastic moments of the four-steel-girder-and-wide-composite-deck specimen were obtained to be 2.4 and 4.1 times the design moment based on the live loading condition of the Korea Bridge Design Specifications (2005). The SCHPB were found to have enough strength for safety under and after construction.