• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.59-67
• /
• 2016

A novel instrumentation amplifier (IA) using fully-differential linear operational transconductance amplifier (FLOTA) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of a FLOTA, two resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into FLOTA converts into two same difference currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the FLOTA and realized the IA used commercial op-amp LF356. Simulation results show that the FLOTA has linearity error of 0.1% and offset current of 2.1uA at input dynamic range ${\pm}3.0V$. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the 60dB was 10MHz. The proposed IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 105mW at supply voltage of ${\pm}5V$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.801-807
• /
• 2022

In this paper, we propose an ultra compact S-Band PCM/FM telemetry transmitter. The equipment is compact, so it can be applied to a limited space and capable of stable data transmission was designed and manufactured even with specifications set differently for each operating environment and system. RF direct conversion structure is used for the miniaturization of equipment, an RF transmission board, Power distribution board, and a signal processing board were implemented on a single PCB, so that the function of the transmitter could be performed with a minimum device. According to the target specification, variable output of 1~10W and variable data rate of 390kbps~12.5Mbps is possible in S-Band(2,200~2,400MHz) without degradation of performance. To verify the performance of the equipment, the RF performance test and BER measurement test were performed after the equipment was manufactured. It was confirmed that the OBW, null-to-null bandwidth, 1st IMD, Spurious emission, Phase noise specification of the PCM/FM modulated signal which is presented by the IRIG standard were satisfied, and we can confirm the data received using the transmitter inspection equipment were transmitted normally without distortion.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.2
• /
• pp.61-67
• /
• 2018

Welding preheating means that the surface of the base material to which the metal is welded before the main welding is heated to a constant temperature. It prevents the cracks of the adjacent influences such as reduction of material hardening degree by controlling the cooling rate, suppression of segregation of impurities, prevention of thermal deformation, and moisture removal. For this reason, it is a necessary operation for high quality welding. Induction heating is an efficient heating method that converts electric energy into heat energy by applying electromagnetic induction phenomenon. Compared with combustion heat generated by gas and liquid, it is clean, stable, and economical as well as rapid heating. It can be heated regardless of the shape, depth and material of the heating body by modifying the shape of the frequency and the coil with a simple structure. In this paper, we implemented a low frequency welding preheating system using induction heating technique and observed the temperature changes of coil resistance, inductance and automotive transmission parts according to the height of each transmission in winding coil for three kinds of automotive transmission parts. We confirmed that the change of current is a very important factor in the low frequency heating.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.377-383
• /
• 2012

In this paper, a new design of a planar rectenna system and its application to a wake-up receiver operating for incoming signal with a specified frequency are proposed for low-power sensor system applications. The planar and integrable rectenna system is designed with DGSs(Defected Ground Structures) at 2.4 GHz. The DGSs reject harmonic components of 4.8 and 7.2 GHz and eliminate 2.4 GHz fundamental frequency for DC-path filtering. The rectenna system has been evaluated for the conversion output voltages, and applied to the switching of a power supply at the low-power sensor receivers. The proposed system has been evaluated for the wake-up performance by testing a lownoise amplifier operation. From the experimental results, the proposed receiver system presents excellent operation performances.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.5
• /
• pp.548-555
• /
• 2001

In this paper, we proposed a HVS(human visual system) model-based digital image watermarking which is not only invariant to rotation and translation but also more robust to lossy compression, cropping, and scaling as compared to the conventional method. Fourier transform and log-polar mapping is used to make the proposed algorithm invariant to rotation and translation, and in addition, watermark energy is embedded maximally based on spatial frequency sensitivity of HVS without the deterioration of the invisibility. As a result, the robustness of watermarking is improved both in general image processing operations such as cropping, low pass filtering, and lossy compression and in geometrical transforms such as rotation, translation, and scaling. And, by disjoint embedding of the watermark and the template without intersection, the deterioration of invisibility and robustness is prevented. Experimental results show that proposed watermarking is about 30~75 [%] more robust af compared to the conventional methods.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.182-188
• /
• 2018

In order to increase the robustness of the uplink for UAS(Unmanned Aerial System), we propose a jamming signal rejection algorithm. In the UAS datalink system, DSSS (direct sequence spread spectrum) is used to reduce the radio noise or jamming signal. In general, jamming signals below the spreading gain are recoverable but the signals beyond the spreading gain can not be recovered. In this paper, these jamming signals beyond spreading gain are detected using the threshold detector in the spectrum area then, generate the estimated signals from the sine wave generator. Finally, we obtain the desired signal to remove jamming signals from the received signals. The proposed scheme can eliminate jamming signals while minimizing the hardware complexity and the original signal loss.

• The Journal of the Acoustical Society of Korea
• /
• v.8 no.1
• /
• pp.5-12
• /
• 1989

This paper is concerned with the characteristics on the statistical parameters of vibration signal from bearing with changing its operating conditions as well as the spreading of faults. The rms, Kurtosis, crest factor, probability of exceedance and probability density function have been chose as the statistical parameters. To characterize of each, vibration signals have been recorded from four ball tester at different loads, operation speeds and time. The values of the statistical parameters for each frequency band have been calculated after A/D conversion and digital filtering of the recorded signals. It has been found that unlike rms values the statistical parameters such as Kurtosis etc. are almost unchanging with the change of the operating conditions such as load and speed. This suggests that the statistical parameters may be used for determining the development of faults independent of the operating conditions. In fact, the statistical parameters deviate considerably from their respective normal values when the faults developed under load conditions in the samples, conforming the suggestion.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.985-991
• /
• 2008

This paper presents a novel balanced mixer receiver front-end design based on a metamaterial structure applicable to differential-/common-mode excitation. This metamaterial structure functions as a leaky-wave antenna and provides in-trinsic common-mode suppression. Low LO leakage and high RF to LO isolation are achieved without additional filters for LO and RF paths. The metamaterial is based on a unit-cell which under a differential-mode excitation behaves like a composite right/left-handed(CRLH) metamaterial. In contrast, the metamaterial unit-cell is below cut-off under a common-mode excitation. Experimental results are used to verify the proposed metamaterial's differential-/common-mode characteristics. The metamaterial is integrated with a balanced mixer design resulting in an operation frequency range of $1.96{\sim}2.40$ GHz with an optimum mixer conversion loss of 21.1 dB at 2,4 GHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.496-503
• /
• 2009

In this paper, a new three-phase interleaved isolated high efficiency boost dc-dc converter with active clamp is proposed. The converter is capable of increased power transfer due to its three-phase power configuration, and it reduces the rms current per phase, thus reducing conduction losses. Further, interleaved operation of three-phase boost converter reduces overall ripple current, which is imposed into fuel cells and realizes smaller sized filter components, increasing effective operating frequency and leading to higher power density. Each output current of three-phase boost converter is combined by the three-phase transformer and flows in the continuous conduction mode by the proposed three-phase PWM strategy. An efficiency of above 96% is mainly achieved by reducing conduction losses and switching losses are reduced by the action of active clamp branches, as well. The proposed converter and three-phase PWM strategy are analyzed, simulated and implemented in hardware. Experimental results are obtained on a 500 W prototype unit, with all of the design verified and analyzed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.301-301
• /
• 2010

현재 전 세계는 앞으로 사용 될 대체 에너지에 많은 관심 가지고 있다. 지금 사용하고 있는 에너지 연료는 한정되어 있기 때문에 대체에너지에 대한 연구가 활발히 진행 되고 있다. 그 중 압전체를 이용한 에너지 하베스팅은 많은 주목을 받고 있다. 주변 환경에서 필요한 에너지를 끌어 쓸 수 있는 대표적인 청정에너지 시스템 중 하나이기 때문이다. 최근 전원 공급원으로써 에너지 수확 시스템은 현 사회에 사용되고 있는 배터리로 전원을 사용하는 제품들을 소용량과 저전압 분야에서의 에너지 수확의 원리를 이용하여 전기전자제품의 사용시간 연장 및 응용분야 확대를 시도하는 연구가 활발히 수행되고 있다. 압전세라믹스를 이용한 에너지 하베스팅은 진동에너지를 전기에너지로 변환하는 것으로서 압전 특성이 높아야 한다. 일반적으로 압전 세라믹스는 PbO 성분이 들어가므로 환경적 오염 뿐만 아니라 인체에도 영향이 좋지 않으므로 많은 나라에서 이러한 성분을 제한하고 점차적으로 줄어들고 있는 시점에서 PbO를 사용하지 않고 Lead-Free 세라믹를 사용한 연구가 진행되고 있다. 이 논문에서는 일반적인 소결 방법을 이용하여 (Na,K)NbO3 세라믹에 CeO2를 첨가한 압전 세라믹을 제작하였다. 제작된 압전 세라믹스로 에너지 하베스팅 소자를 제작하고, 이 소자로 수확된 에너지로 DC-DC Converter 응용 특성에 대하서 연구하였다. 압전 세라믹스의 좋은 압전 특성을 출력하기 위하여 캔틸레버의 고유 진동수가 진동원의 주파수와 일치하는 공진을 일으켜야 한다. 따라서 구동회로는 주파수원을 찾아 설계하였고, 압전 세라믹스의 진동은 가진기를 이용하여 구동실험을 하였다. 지금까지 나와있던 에너지 하베스팅 회로와 비교하여 그 특성을 분석하고, 시뮬레이션 및 실험을 통하여 검증하였다.