• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.3
• /
• pp.43-51
• /
• 1986

Triaxial compression tests were performed with control of vertical stress, confined pressure(${\sigma}_H$), and injection velocity by means of impervious soil samples with a different grain size, density and grout density. By measuring pore water pressure at the time of vertical fracturing around the bore-hole, relationships between main factors are described, and the factors are pore water pressure, confined pressure, vertical fracturing injection pressure(${\sigma}$) and the tension strength(${\sigma}_t$). The hydraulic fracturing of soft clay was occurred at the pressure which was less than the pressure obtained by the theory of elasticity. It was found that the above result was the influence of pore water pressure due to injection pressure($U_a$) and pore water pressure due to confined pressure($U_i$). Therefore, the vertical injection pressure at the time of fracturing needs to be changed as follows. $${\sigma}=2{\cdot}{{\sigma}_H}-(U_a+U_i)+{\sigma}_t$$.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.73-82
• /
• 2023

In this study, the optimal method for injection of neutralizer to restraint the leakage of acid drainage in embankment structure composed of pyrite rocks is proposed. Finite Element Analysis was performed to examine the seepage effect caused by injection of neutralizer into the embankment structure. The diameter of the neutralizer injection hole was selected as 50cm, the interval space of injection ranged from 1m to 4m and the injecting pressure ranged from 100kPa to 220 kPa were applied for the numerical analysis. According to the analysis results, the saturation time of the whole embankment structure was shown to be fast at a relatively low injecting pressure in the case of injecting interval space of 1.0m and injecting pressure of 130kPa and in the case of injecting interval space of 2.0m and injecting pressure of 160kPa. When the interval space of injection for saturation of whole embankment structure is selected as 3m, various injection pressures can be applied from 130kPa to 190kPa, and the saturation time of whole embankment is similar regardless of the injection pressure. Therefore, the optimal method for injection of neutralizer considering economic efficiency was selected as injecting interval space of 3.0m and injection pressure of 130kPa.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.471-475
• /
• 2015

Because of increasing demand, a small portable drug injector that uses osmotic pressure for its operation force is developed, and its performance is evaluated. The osmotic drug injector can be small and lightweight because it does not require heavy batteries and an actuator, unlike previous electromechanical drug injectors. Moreover, its injection pressure can be sustained longer than that of previous elastic drug injectors. The new device is composed of a drug sac, osmotic pressure chamber, semipermeable membrane, and solvent chamber. To evaluate its performance, an in-vitro experiment was designed to measure the outflow and the injection pressure with respect to time. The experimental results show that the new drug infuser can continuously deliver 20 ml drug over a period of 20 h. The maximum injecting pressure was over 400 mmHg. Which prevents backflow caused by changes in the outlet pressure resulting from changes to the position of the device and the patient's posture.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.217-225
• /
• 2003

The ground reinforcement effect of pressure grouting depends on grout penetration into ground. It is not, however, easy to predict the grout penetration in the design process because of the heterogeneity of ground conditions. This study investigates the proper grouting pressure and grouting method through laboratory model tests for pressure grouting using loose to medium dense crushed rock and sandy ground using specially designed and fabricated device. The optimum injection pressure, grout quantity and injection time are investigated through performing pressure grouting under changing conditions of injection in this test. From the test results, it was found that optimum injection pressure covers the range of 3 to 4kg/cm$^2$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.4
• /
• pp.70-77
• /
• 2010

Microcement grouting and micro pile are frequently used for ground modification during tunnel construction. The influence of grouting pressure of microcement grouting and micro pile to the existing bridge which is directly over the constructing tunnel is investigated. Three dimensional seepage flow-structure interactive analysis considering firm water pressure with full stages of construction including the construction of upper bridge, microcement grouting, micro pile and tunnel is performed. The settlement and tilting of the pier of existing bridge violate the design code and the reaction of the bridge are highly increased after grouting. The stress of tunnel bracings such as rockbolt and shotcrete also exceed the limit of the code. The pressure of microcement grouting is confined by bedrock and transmit to the surrounded soil and the upper bridge. Microcement grouting needs mid-high pressure to penetrate through weak fault plane and the pressure greatly influence the safety of the upper structure. It is important to decide and care the grouting pressure to improve weak fault plane directly under the existing structures and the pressure of microcement grouting should be considered in underground analysis.

• Tunnel and Underground Space
• /
• v.32 no.3
• /
• pp.203-218
• /
• 2022

A hydro-mechanical study was performed to analyze the relationship between the magnitude of injection-induced seismicity and shut-in. In hydraulic analysis, the suspension of fluid injection makes the pore pressure gradient smaller while the pore pressure at the pressure front can reach the critical value for several hours after shut-in, which leads to the additional slip with wider area than during injection. The hydro-mechanical numerical analysis was performed to model the simplified fault system, and simulated the largest magnitude earthquake during shut-in stage. The effect of the abrupt suspension of fluid injection on the large magnitude earthquake was investigated in comparison with the continuous injection. In addition to the pore pressure distribution, it was found that the geometry of multiple faults and the stress redistribution are also important in evaluating the magnitude of the induced seismicity.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.3
• /
• pp.151-165
• /
• 2021

Grouting, which is applied for the increase of ground strength and the decrease of permeability, is complex process because of several reasons, so the process needs to be elaborated. Injection process in consideration of ground condition and optimization of grouting sequence is essential. In this study, GIN (Grouting Intensity Number), multiple of injected grout volume and pressure, is revised to consider injection pressure reduction and joint opening during grouting process. A revised GIN process is evaluated through a field test. A revised GIN, considering ground condition, injection pressure, follows GIN envelope and produces rational grouting process. The result of a revised GIN reduces permeability of the ground in the order of 10^-1~10^-2 cm/sec.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.222-222
• /
• 1999

플라즈마 이온주입장치는 수십 kV의 음전압 펄스를 타겟에 인가하여 플라즈마 쉬스 전위에 의해 이온을 가속시켜 다차원 형태의 타겟 표면의 내마모성, 강도 및 경도를 쉽고 간단하게 증가시킬 수 있는 신기술 장비이다. 이때 인가되는 음전압 펄스는 펄스회로가 갖는 RC로 인하여 고유한 유한 오름시간의 음전압 펄스가 타겟에 인가되고 펄스 특성에 따라 타겟 주변에 시변환 쉬스가 형성되는데 시변환 쉬스에 대한 정확한 이해를 통해서 시편에 주입되는 이온의 양을 예측할 수 있다. 본 연구에서는 유도 결합형 플라즈마를 이용한 플라즈마 이온주입장치에서 평면 타겟 경우의 펄스 오름시간, 유지시간 및 내림시간 동안에 형성되는 쉬스의 거동 및 타겟의 크기가 쉬스에 미치는 영향을 실험적으로 관찰하고 이론결과와 비교하였다. 기존의 실험에서 펄스 유지시간 이후의 탐침전류 곡선에서 쉬스의 거동처럼 보였던 현상은 ion acoustic wave의 진행으로 보이며 위치에 따른 탐침 전류 곡선의 정확한 해석을 통하여 실제 플라즈마 이온주입장치내에서의 쉬스의 거동을 관찰할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.240.1-240.1
• /
• 2014

대기압 플라즈마 제트 장치에 주입되는 기체의 유량 변화에 따른 방전 특성을 유체역학적으로 해석하였다. 장치에 주입되는 기체의 유량 변화는 레이놀즈수에 의한 유체 흐름의 상태 변화와 베르누이 정리에 의한 압력 변화를 동반한다. 유리관에 주입되는 기체의 레이놀즈수가 Re<2000이면 층류이며 Re>4000이면 난류, 2000

• The Journal of Engineering Geology
• /
• v.5 no.2
• /
• pp.129-138
• /
• 1995

To elucidate the effects of flow rate on the hydraulic fracturing property of andesite, the hydraulic fracturing tests were conducted under three flow rates. As the tests are conducted with 1ml/min, 2ml/min and 3 ml/min under the constant axial load of 40 kN, the breakdown pressures of andesite seem to be constant as 163kg/cm$^2$. The hydraulic fracturing tests were carried out under the temperatures of five stages to elucidate the effects of temperature variation on hydraulic fracturing property of granite. As the tests are carried out under the constant flow rate of 1.7ml/min, with the axial load of 40kN, the breakdown pressures of granite are 168kg/cm$^2$ at room temperature, and 124kg/cm$^2$ at 20$0^{\circ}C$. The breakdown pressure decreases about 25% than that of room temperature with increasing the temperature. Under the controlled flow rates, the initiation pressures of the microcracks of granite are well coincided with the breakdown pressures and these results are also confirmed by the levels of acoustic emission.