• Journal of Korea Foundry Society
• /
• v.43 no.4
• /
• pp.194-200
• /
• 2023

The heat transfer of the mold in the casting process has been calculated by considering the mold as a uniform isotropic material. Since the mold was not a uniform isotropic material, however, the calculation was performed with approximate values, and in particular, estimated values were used when considering compaction and the amount of added binder. In this study, a calculation algorithm of the thermal properties of the sand mold was developed. An algorithm for calculating the thermal conductivity and specific heat based on a thermal resistance model in the case of mono-dispersed sand grains was also developed and applied to sand molds with various size distributions. The thermal properties of sand were calculated for artificial sand, and relatively close values compared to the experimental values were obtained.

• Korean Journal of Heritage: History & Science
• /
• v.43 no.3
• /
• pp.102-121
• /
• 2010

Three bronze bells excavated from the Hoeamsa temple site were investigated for their microstructures and chemical compositions in an effort to understand the technology applied in fabrication, which may represent the related industry established in the early Joseon period. The result shows that the bells were cast from alloys of approximately 85% copper-8% tin-7% lead. The chemical analysis for ten trace elements shows that they were all kept below 0.3 weight %, suggesting that the alloys were made of relatively well-refined copper, tin and lead. The presence of sulfur and iron indicates that chalcopyrite or chalcocite may have been used in the smelting of copper. Evidence has been found that the bells were cast by pouring the liquid metal from the top of the sand molds that were set up in an upright position. No additional treatments, thermal or mechanical, other than a little grinding were applied upon the completion of casting. After the shaping process, a balancing plate was attached to the top of the bell using a steel connection ring. The connection assembly was then fixed to the main body by using molten bronze as a solder. The surface inscription was found carved using different techniques. The differences in the order of strokes and the calligraphic style indicate that the carving was carried out by more than one master. In the absence of documentary evidence on past bronze technology, the present bronze bells with known chronology, provenance and the main agent of production, prove to be a rare and valuable archaeological material for the understanding of the related technology in use in the early Joseon period.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1085-1088
• /
• 2001

The process of styrofoam pattern that has been used for material of press die pattern depends chiefly on handwork. Laser manufacturing system developed to increase precision and efficiency of process that is also able to convert the design easily. Applying the RP(rapid prototyping) concept reversely, the unnecessary part of section is vapored away by heat source of laser beam after converting 3-D CAD model into cross-sectional shape information. Laser beam is line-scanned in plane specimens to measure the depth and width of cut, surface roughness, cross-sectional shape as converting laser power, scanning speed, cutting gas pressure. With these basic data, plane surface, inclined surface, hole, outer contour trimming process is experimented and optimum condition are obtained. In plane and inclined surface experiments, 15W laser power and 50mm/s scanning speed make superior processing property and 30W, 10mm/s make processing efficiency increase in trimming process. With these results, simple patterns were manufactured and the possibility of applying laser manufacturing system to styrofoam pattern was convinced.

• Journal of Korea Foundry Society
• /
• v.9 no.4
• /
• pp.327-335
• /
• 1989

The matrix structure and the morphology of CV graphite are affected by the addition of many kinds of elements, which are contained in the CV graphite cast iron, additives, fading time and cooling rate. The effects of cooling rate on the matrix structure, the shape of CV graphite, mechanical properties and propagation of ultrasonic wave in hypoeutectic CV graphite cast iron were studied. When the diameters of the samples are 50mm, 35mm and 20mm 1. CV graphite number showed average 17.9% increase and CV graphite length showed 10.3% decrease with decreasing diameter of the samples. 2. The amount of graphite and ferrite showed average 11.2, 4.1 % decrease and the amount of pearlite showed average 15.7% increase. 3. Hardness and tensile strength showed average 3.5%, 11.3% increase and impact strength showed average 1.5% decrease. 4. Ultrasonic wave velocity showed average 1.1% increase.

• Journal of Korea Foundry Society
• /
• v.9 no.4
• /
• pp.336-344
• /
• 1989

The matrix structure and the morphology of CV graphite are affected by the addition of many kinds of elements, which are contained in the CV graphite cast iron, additives, fading time and cooling rate. The effects of cooling rate on the matrix structure, the shape of CV graphite, mechanical properties and propagation of ultrasonic wave in eutectic CV graphite cast iron were studied. When the diameters of the samples are 50mm, 35mm and 20mm 1. CV graphite number showed average 13.8% increase and CV graphite length showed 12.3% decrease with decreasing diameter of the samples. 2. The amount of graphite and ferrite showed average 10.6, 4.3% decrease and the amount of pearlite showed average 23.4% increase. 3. Hardness and tensile strength showed average 3.2%, 9.5% increase and impact strength showed average 1.3% decrease. 4. Ultrasonic wave velocity showed average 1.1% increase.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.477-482
• /
• 1995

A computer simulation model of various smelting process for melting waste sand was developed by using energy and material balance concept. This model can predict the coal, flux and oxygen consumption and the volume and temperature of off-gas. The major critical variables for smelting process can be explained by using the analysis of energy and material balance. The major conclusions were as follows; 1. The most important variables for smelting process were high post-combustion ratio, high heat transfer efficiency and refractory protection technology. 2. For saving energy in this smelting process, selection of raw materials i.e coal, flux are very important, espacially using of low volatile coal is very profitable. 3. The treatment cost of waste sand is high and environmental restriction is severe, in this reason we must be concerned in the treatment of waste sand by smelting process.

• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.224-228
• /
• 2001

자동차용 Al Wheel의 반복 금형 주조 공정에 있어서의 적정 냉각조건 확립 및 수축공 등의 주조결함을 제어하기 위하여 3차원 응고, 유동, 응력 해석 프로그램 연동 기술과 자동 금형온도 조절장치를 실제 현장에 적용하여 생산되는 Al Wheel 제품의 최적 주조조건 및 냉각조건을 확립하였다. 주조과정 중의 금형의 온도 변화 및 주물의 응고, 유동 거동은 수치해석 결과와 잘 일치하는 경향을 나타내었다. 또한 금형온도 자동 조절 장치를 사용함으로서 금형 작업온도의 가열 및 유지가 정량적으로 제어 가능하며, 제품 품질의 유지 및 Cycle Time 최적화를 이룰 수 있으며 궁극적으로는 금형 수명 연장 및 생산성 향상 등을 이룰 수 있었다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.85-89
• /
• 2010

The uranium ingot casting process is one of the steps which consolidate uranium deposits produced by electrorefiner as an ingot form in a pryprocessing technique. This paper introduces new design concept of the ingot casting equipment and the performance test results of the lab-scale ingot casting equipment fabricated based on the design concept. Casting equipment produces the uranium ingot by pouring an uranium melt into a mold by tilting a melting crucible. Also it is equipped with a cup which is able to continuously feed uranium deposits into a melting crucible. The productivity could be significantly enhanced by introducing the continuous operation concept.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1519-1526
• /
• 2013

This study reviewed the capturing performance of a canopy hood used in some melting processes of a casting manufacturing factory through a site survey. In addition, this study compared and evaluated the flow field and pressure field for the plans to enhance the hazardous air pollutants collection capacity by using CFD model. The case-2(flange attached + double hood) can be improved in terms of collection performance, but is expected to increase in hood static pressure by about 70% more than the existing structure, so it was shown that its site applicability is not good. It is judged that the shape of case-3(flange attached + double cone attached) is most suitable to improve the suction efficiency. This is because a double cone is installed at the center of the opening to concentrate the flow rate on the edge of the hood and control the hume rising to the center of the hood without a static pressure rise via the slope of the cone.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.367-376
• /
• 2012

The ironware production technology is a measure to fathom the society's level of development in time. To understand iron-manufacure methods in the past, various investigations on the fine structures and additions of ironware remains and Iron ingot have been conducted in a way of natural science. This study metallurgically reclassifies remains excavated in iron-manufacture remains located in Beokje, Goyang, which are thought to be in time of Goryeo Dynasty, and draws an inference from the element analysis on the iron-manufacture and smelting technology. Iron ingot samples with a cast iron structure are divided into those with a white cast iron structure and those with a grey cast iron rich in P. The P content of grey cast iron appeared to be the result of adding a flux agent like lime, iron ingot and carbon steel iron ingot with a cast iron structure excavated in the area is regarded as pig iron which was made without a refining process. In this study it seems that two methods of making ironware were used in the area; one is the method of making ironware by pouring cast iron to the casting, and the other is the method of making carbon steel through the refinement of pig iron. It appears that highly even steel structure of carbon steel and a small amount of MnS inclusion are very similar with that of the modern steel to which Mn is artificially added. Nevertheless, these data alone cannot be used to determine the source of Mn in the carbon steel of the excavated from the iron-manufacture remains, which raises the need for further studies on the source and the possibility of carbon steel via the iron-manufacture process of cast iron.