• Journal of Korean Society of Steel Construction
• /
• v.18 no.5
• /
• pp.633-642
• /
• 2006

Serviceability design is required to control the cracking at the joint of precast decks with longitudinal prestress in continuous composite bridges. Details of twin-girder bridges are especially complex not only due to their main reinforcements and transverse prestresses for the design of long-span concrete slabs, but also due to the shear pockets for obtaining the composite action. This paper suggests the design guidelines for the magnitude of the effective prestress and for the selection of filling materials and their requirements that would allow for the use of precast decks for twin-girder continuous composite bridges. The necessary initial prestress was also evaluated through long-term behavior analysis. From the analysis, existing design examples were revised and their effectiveness was estimated. When a filling material with a bonding strength higher than the requirement is used in the region of a high negative moment, a uniform configuration of the longitudinal prestressing steels along thewhole span length of continuous composite bridges can be achieved, which would result in the simplification of the details and the reduction of the construction costs.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.159-165
• /
• 1998

중트럭 통행으로 인한 철근콘크리트 교량바닥판의 열화는 교량구조물을 유지보수하는데 있어 심각한 문제 중 하나이며, 프리캐스트 바닥판을 이용한 교량바닥판의 시공 및 교체 방법이 실용적이며 효과적인 방법으로 인식되고 있다. 본 연구에서는 횡방향 ddusruf부에 종방향 프리스트레싱을 도입한 프리캐스트 바닥판의 모델을 제작하여 바닥판간 횡방향 연결부의 강성 평가 및 연결부의 피로 거동을 파악하기 위해서 피로실험을 수행하여 피로하중하에서의 휨강성의 변화, 균열발생 및 파괴하중 등을 측정하였다. 실험결과를 통해서 피로하중하에서 프리스트레스 프리캐스트 부재의 프리스트레스 효과를 평가하였으며, 현장타설에 의해서 시공되는 일반 RC 부재에 비해서 우수한 구조적 거동을 보여주는 적정량의 종방향 프리스트레스 크기를 결정하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.499-509
• /
• 2006

Precast concrete deck has many advantages comparing with the in-situ concrete deck, and has been successfully applied to replacement of the deteriorated decks and to the newly constructed highway bridges in domestic region. In order to apply the precast decks into the railway bridges, however, differences of the load characteristics between the highway and the railway should be properly taken into account including the train load, longitudinal force of the continuous welded rail, acceleration or braking force, temperature change and shrinkage. Proper level of the longitudinal prestress of the tendons that can ensure integrity of the transverse joints in the deck system is of a primary importance. To this aim, the longitudinal tensile stresses induced by the design loads are derived using three-dimensional finite element analyses for the frequently adopted PSC composite girder railway bridge. The effect of the temperature change is also investigated considering the design codes and theoretical equations in an in-depth manner. The estimated proper prestress level to counteract those tensile stresses is above 2.4 MPa, which is similar to the case of the highway bridges.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.679-688
• /
• 2003

For box girders in which the longitudinal tendon is profiled in the inclined webs, longitudinal prestressing force will induce transverse effects as well as longitudinal ones. In this paper, the method to estimate transverse effects induced by longitudinal prestressing is proposed. The concept of transverse equivalent loading which is calculated through longitudinal prestressing analysis is developed. The transverse stress in slabs of box girders due to longitudinal prestressing are investigated. The comparison of numerical results of the proposed method and those of folded plate method represents that the method is reasonable. Numerical analyses are carried out depending on the parameters such as web inclination and ratio of girder length to tendon eccentricity. Analysis results show that when only prestressing are considered the magnitude of transverse stress in slabs of box girder is not so large. However, if the other stresses due to dead and live load et al. are superposed on these stresses, it may be that the longitudinal prestressing effects are significant.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.127-128
• /
• 2009

This study was conducted to develop the design methodology of longitudinal post tensioning for the prestressed concrete pavement (PSCP).

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.178-181
• /
• 2011

본 연구에서는 광섬유센서를 내장한 스마트강연선을 이용하여 초고성능콘트리트로 제작된 하이브리드 사장교 세그먼트의 횡방향 도입 긴장력을 계측하고 세그먼트 내부의 프리스트레스를 계측하여 즉시손실에 해당하는 정착장치 활동에 의한 손실과 마찰손실을 도로교설계기준(2005)의 설계 마찰손실과 비교하였다. 제작된 2개의 UHPC 사장교 세그먼트는 횡방향 길이 16.7m, 종방향 길이 1.75m, 높이 1.5m이며 각 시험체의 1/4, 1/2, 3/4지점에 긴장력을 계측하기 위해 3개의 FBG센서를 배치하였다. 긴장력은 유압잭을 이용하여 5개의 강연선에 동시에 순차적으로 도입되었으며, 단부에서 최대 도입 긴장력은 세그먼트 1은 734kN, 세그먼트 2는 639kN이었다. 도로교설계기준에 제시된 마찰계수의 중간값(파상마찰계수=0.00405, 곡률마찰계수=0.20)을 사용하여 FBG센서 위치에서 계산된 긴장력은 계측치와 5% 이내의 차이를 보였으며, 정착장치 활동에 의한 순간손실은 긴장단에서 최대 12.8%로 계측되었다. 이로부터 이 연구에서 제시하는 긴장력계측방법의 적용성을 입증할 수 있었으며, 향후 이 방법은 프리스트레스트 콘크리트 교량의 설계기준 마찰계수 개정을 위한 연구에 좋은 도구로 활용될 수 있을 것으로 기대된다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2001

Recently, prestressed concrete(PSC) bridge structures with many repetitive spans have been widely constructed using the segmental construction method in many countries. In these segmentally constructed PSC bridges, there exist many construction joints which is required coupling of tendons or overlapping of tendons to introduce continuous prestress through several spans of bridges. The purpose of this paper is to investigate in detail the complicated stress distributions around the tendon coupled joints in prestressed concrete girders. To this end, a comprehensive experimental program has been set up and a series of specimens have been tested to identify the effects of tendon coupling. The present study indicates that the longitudinal and transverse stress distributions of PSC girders with tendon couplers are quite different from those of PSC girders without tendon couplers. It is seen that the longitudinal compressive stresses introduced by prestressing are greatly reduced around coupled joints according to tendon coupling ratios. The large reduction of compressive stresses around the coupled joints may cause deleterious cracking problems in PSC girder bridges due to tensile stresses arising from live loads, shrinkage and temperature effects. The analysis results by finite element method correlate very well with test results observed complex strain distributions of tendon coupled members. It is expected that the results of this paper will provide a good basis for realistic design guideline around tendon coupled joints in PSC girder bridges.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.2 no.3 s.6
• /
• pp.101-108
• /
• 2002

There exist many construction joints in segmentally constructed bridge girders. It is required coupling of tendons or overlapping of tendons to introduce continuous prestress through several spans of bridges. Even though tendon coupling method is easier to use in practice, some cracking problems around construction joints have been reported and complicated stress states around construction joints in PSC girders is not clearly investigated. The purpose of this paper is to investigate in detail the complicated longitudinal stress distributions around the construction joints in prestressed concrete girders with tendon couplers. To this end, a comprehensive experimental program has been set up and a series of specimens have been tested to identify the effects of tendon coupling and segmental construction of bridge sections. The present study indicates that the longitudinal stress distributions of PSC girders with tendon couplers are quite different from those of PSC girders without tendon couplers. The longitudinal compressive stresses introduced by prestressing are greatly reduced around coupled joints according to tendon coupling ratios.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.257-267
• /
• 2008

This study was conducted to investigate the stress distribution in the prestressed concrete pavement (PSCP) when the transverse post tensioning was applied. By performing the structural analyses using a finite element model of PSCP, the effect of anchor spacing and the relationship between the longitudinal and transverse post tensioning were evaluated. The analysis results showed that as the anchor spacing became smaller, the stresses were more uniformly distributed and the ranges of the stress losses were reduced; however, the economy should be considered. As the anchor spacing became larger, the difference between the average transverse stress and the transverse stresses at various locations such as shoulder, wheel pass, and center of the slab, increased. The transverse post tensioning induced the additional tensile forces in the longitudinal tendons, but the magnitude was negligibly small, and the longitudinal and transverse post tensioning could be designed independently. The use of the transverse stress distribution for the design of the post tensioning was also discussed in this paper.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.341-344
• /
• 2008

In this paper, the effect of flame cutting order of tendons on the concrete stress was investigated experimentally. For this, the three slab specimens with 14 tendons were cast and tested. During the detensioning, the longitudinal and transversal strain were measured. Test results showed that the measured strains of transversal stirrups were varied by the cutting order.