• Journal of the Korean Society of Hazard Mitigation
• /
• v.3 no.4 s.11
• /
• pp.103-109
• /
• 2003

A numerical analysis of cable-stayed bridge is conducted to determine optimum longitudinal modulus of elasticity which represents the boundary condition between the tower and main girder. The effect of longitudinal modulus of elasticity is investigated for different loading condition (live load, wind load, seismic load), respectively. There are significant changes in the member forces as variations of longitudinal modulus of elasticity, such as, $k_h$=e=100tonf/m/bearing (live load), $k_h$=e=1000tonf/m/bearing (seismic load), However, the wind loads do not affect member forces. The optimum longitudinal modulus of elasticity is determined from considering minimum member forces in the numerical analysis results.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.60-70
• /
• 1999

The longitudinal stability characteristics of a Wing-In-Ground Effect Craft are quite different from that of the conventional airplane due to the existence of force and moment derivatives with regard to height. This stability characteristics plays a great role in designing a safe and efficient WIG due to its potential danger in sea surface proximity. The static and dynamic stability criteria are derived from the motion equations of WIG in the framework of small disturbance theory and discussed in the paper. The static and dynamic stability analyses of a 20-passenger WIG are conducted based on the wind tunnel test data and the dynamic motion behaviors are investigated for the change of the design parameters. Finally, the flying quality of the 20-passenger WIG is analysed at the cruising condition according to the military regulations.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.5
• /
• pp.675-687
• /
• 2019

In recent years, the needs for double deck-tunnels have increased in large cities due to the increase in traffic volume and high land compensation costs. In Korea, a network type tunnel which is smaller than general road tunnels and crosses another tunnel underground is planned. In the shield tunnel joints between the existing shield tunnel and the box-type enlargement section, a partial steel-concrete joint is proposed where the bending moment is large instead of the existing full-section steel joint. In order to analysis the enlargement section of the shield tunnel diverged section to reflect the three-dimensional effect, the two-dimensional analysis model is considered to consider the column effect and the stiffness effect of the longitudinal member. A two-dimensional analysis method is proposed to reflect the stiffness of the longitudinal member and the column effect of the longitudinal point by considering the rigidity of the longitudinal member as the elastic spring point of the connecting part in the lateral model. As a result of the analysis of the model using the longitudinal member, it was considered that the structural safety of the partial steel-concrete joint can be secured by reducing the bending moment of the joint and the box member by introducing the longitudinal member having the stiffness equal to or greater than a certain value.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.149-160
• /
• 1999

This paper is a part of a research aimed at the verification of basic design rules of high-strength concrete columns. A total of 32 column specimens were tested to investigate structural behavior and strength of eccentrically loaded reinforced concrete tied columns. Main variables included in this test program were concrete compressive strength. steel amount, eccentricity, and slenderness ratio. The concrete compressive strength varied from 356 kg/$cm^2$ to 951 kg/$cm^2$ and the longitudinal steel ratios were between 1.13 % and 5.51 %. Test results of column sectional strength are compared with the results of analyses by ACI rectangular stress block, trapezoidal stress block, and modified rectangular stress block. Axial force-moment-curvature analysis is also performed for predicting axial load-moment strength and compared with the test results. The ACI rectangular stress block provides over-estimated column strengths for the lightly reinforced high strength column specimens. The calculated strengths by moment-curvature analyses are highly affected by $k_3$ values of the concrete stress-strain curve. Observed failure mode. concrete ultimate strain, and stress block parameters are discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.2
• /
• pp.95-106
• /
• 2021

Side-jets enable the immediate maneuver of a missile compared to control surfaces; however, they may cause adverse effects on aerodynamic coefficients, for they interfere with freestream. To find out the impact of side-jets on aerodynamic coefficients, we simulate side-jets as air gas and utilize multi-fidelity models to evaluate differences between aerodynamic coefficients obtained with and without side-jets. We computed differences in aerodynamic coefficients to investigate side-jet effects for the changes of a Mach number, a bank angle, and an angle of attack. As a result, asymmetrically developed side-jets affect the longitudinal force and moment coefficients, and the lateral force and moment coefficients drastically change in-between -30 and 30 degrees of bank angles. In contrast, side-jets hardly influence the axial force coefficients. As for the axial moment coefficient, we could not determine the side-jet effect due to a lack of aerodynamic coefficient samples in the Mach number. All in all, we confirm that side-jets lead to the change of a missile attitude as they considerably vary the longitudinal and lateral aerodynamic coefficients.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.3
• /
• pp.234-240
• /
• 2002

The static stability of the otter board in relation to the angle of attack ($\alpha$) was studied analytically and experimentally from the moments of tensions and hydrodynamic force acting on it. Three flat plates of 0.5, 1.0, and 1.5 aspect ratios (λ) and four cambered plates of 5, 10, 15, and 20% camber ratios (CR) with the same aspect ratio (λ=1.5) were tested in a circulating water tank for measuring the hydrodynamic forces and moments relevant to the position of hydrodynamic center. And, center-of-pressure coefficients ($C_p$) and moment coefficients ($C_M$) of each plate as a function of the angle of attack were calculated for estimating the static stability from hydrodynamic forces. The obtained results are summarized as follows ； 1． When the angle of attack for otter board is changed from equilibrium for some reason, moments depending upon tensions of warp and sweep line always act in order to have the static stability, respectively. 2. Position of center-of-pressure of each flat plate moves from leading edge to center of plate with the increase of the angle of attack. It means that the moment of hydrodynamic force acting on flat plates also increases the static stability of plate. 3. With the increase of the angle of attack for cambered plates, the positions of center of-pressure move from trailing to leading edge, and then turn toward center of plate. As the camber ratios increase, the ranges of the angle of attack of the static un stability depending on moment of hydrodynamic force become wide.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1261-1270
• /
• 2013

The current domestic design criteria of live load employs DL-24 load and DB-24 load. Particularly for long span bridges above 45meters, DL-24 load is forced to apply and design them, since the shearing force and the moment of DL-24 load appears more dominate than those of DB-24. But it appeared that this DL-24 load didn't meet the vehicles traveling load, which affected bridges in real use. Hence this paper defined ML-24 load similar to the load applied to real bridges and also defined a new live load model, RL-24 load, after adjusting the existing DL-24 load, which doesn't meet the moment and the shearing force of ML-24. As the result of applying and reviewing RL-24 load to simple bridges of span of 45~60m, the results satisfying both the moment and the shearing force applied to bridges in real use by traveling load were attained. Besides, the applicability of it was examined in comparison with live load models of home and abroad.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.103-103
• /
• 2015

유류유출사고와 같이 하천 수표면의 흐름에 따라 이동 확산하는 부유성 오염물질의 혼합해석을 위해 많은 연구자들은 입자추적모형을 사용한 혼합모의를 수행해왔다. 입자추적모형에서 오염물질의 혼합은 평균 유속 분포에 의한 결정론적인 이동과 난류유동에 의한 무작위적인 혼합으로 나타내며, 난류혼합에 의한 수평확산은 난류확산계수로 조절한다. 따라서 표면흐름에 의한 난류확산계수의 산정을 위해 많은 연구자들은 부유성 입자를 이용한 실내실험을 수행하여 수평확산계수를 산정했고(Engelund, 1969; Cederwall, 1971), 최근에는 GPS의 발전으로 인해 해양영역에서 GPS를 장착한 표면부자를 활용한 확산실험을 통해 수평확산계수를 산정한 바 있다(Kjellson and $D{\ddot{o}}{\ddot{o}}s$, 2012; Alpers 등, 2013). 하천수질오염사고의 약 43.5%가 유류유출에 의한 것이며(환경부, 2013), 이에 따라 표면흐름에 의한 오염물질 혼합해석이 필요하나, 하천에서 수평확산계수 산정을 위한 현장실험연구는 부족한 상황이다. 따라서 본 연구에서는 낙동강 본류에서 GPS부자를 이용한 입자추적실험을 수행하여 표면흐름에 의한 확산계수를 산정했다. GPS부자를 이용한 입자추적실험은 낙동강의 강정고령보 하류와 구미보 하류의 각각 세 지점에서 수행되었다. GPS부자는 바람에 의한 교란을 최소화하기 위해 지름 10 cm의 구형으로 제작하였으며 시범테스트를 통해 입자의 주 궤적 변화가 크지 않은 지점에 GPS부자를 투입했다. GPS부자는 오염물질의 사고유출을 가정하여 한 지점에 투입했고 GPS부자 사이의 간섭을 최소화하기 위해 25 ~ 35개의 GPS부자를 이용했다. 표면흐름에 의해 이동하는 부자의 위치는 GPS에 시계열로 저장됐고 ADCP를 이용하여 실험당시의 수리량을 측정했다. 입자위치의 시계열자료로부터 GPS부자의 확산범위의 시간변화를 계산했고 단순 모멘트법을 이용하여 종, 횡 방향 확산계수를 계산했다. 그 결과, 종 방향 확산계수는 $0.003{\sim}0.041m^2/s$로 계산되었고 횡 방향 확산 계수는 $0.001{\sim}0.012m^2/s$로 계산되어, 흐름방향의 유속성분에 의한 확산이 지배적인 것으로 나타났다. 지류 합류부에서는 이송이 지배적인 혼합이 발생되었고(Pe>1) Pe의 증가에 따라 수평확산계수가 감소되었다. 25~35개 GPS부자 궤적의 앙상블 평균으로부터 계산한 Integral time scale은 모멘트법으로부터 계산한 종, 횡 방향 확산계수와 비례하는 것으로 나타나, Taylor(1921)의 이론과 일치했다. 또한 실험수로에서 수행된 기존연구결과와 비교한 결과, 하폭 대 수심비, 마찰항의 증가에 따라 수평확산계수가 증가하는 경향을 나타내었다.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.3
• /
• pp.289-299
• /
• 2006

Orthotropic steel decks are manufactured by welding thin plates therefore it is inevitable that there are abundant works of welding process. On connection of transverse rib web, crossing point of longitudinal rib, transverse rib and deck plate and cut-out parts of transverse rib are the significant position of stress concentration phenomenon because of out of plane and oil-caning deformation caused by longitudinal rib distortion with shear force and distortion. In order to reduce the stress concentration phenomenon and improving fatigue performance at the crosing point and cut-out, structural analysis was performed considering the existence of scalop at conection and diaphragm which have same plane with transverse rib placed inside of longitudinal rib. Result o f the analysis show that there are the largest efect of stres concentration reduction when diaphragms are installed without scallop at connection, therefore these detail can improve the fatigue performance of orthotropic steel decks.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.12-17
• /
• 2006

Longitudinal static stability and steady aerodynamic characteristics of wings flying over nonplanar ground surfaces (rail and channel) are investigated using the boundary-element method. For a channel with it's fence higher than the wing height, the lift and the nose-down pitching moment increase as the gap between the wingtip and the fence decreases. For a rail with it's width wider than the wing span, the lift and the nose-down pitching moment increase as the rail height decreases. Longitudinal static stability of a single wing flying over nonplanar surfaces is worse than the case of the flat ground. In case of tandem wings, longitudinal static stability of the wings flying over the channel is better than the case of the flat ground. It is believed that the present results can be applied to the conceptual design of high-speed ground transporters.