• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.4
• /
• pp.172-179
• /
• 1988

A cartridge type hydraulic logic valve consists of simple two port valve whose poppet is closed or opened by means of pressure signal of a pilot line. Accordingly, the logic valve can be used not only for direction, flow and pressure control purpose but also for versatile function valve which enables all above mentioned functions. In addition, the valve has little internal leakage and pressure loss, superior response characteristics and easiness in making small block type valve. The above mentioned good performances being recognized recently, the logic valve has been used widely in the large scale hydraulic system such as a hydraulic press system, for the performance requirements of high speed operation and precise control characteristics. However, there are scarce reports until now, except for a few ones from Aachen Institute of Technology in West Germany, so it is necessary to be studied on development and investigation for practical application. This paper showed that the static and dynamic characteristics of a logic valve when the logic valve is used for directional control, to investigate the relations between the valve operating characteristics and the valve design conditions. From the above mentioned procedure, it was ascertained that the valve operation characteristics obtained by numerical analysis showed good agreements with experimental results. The representative results obtained are as follows; 1. During the valve is closing, the poppet velocity is almost constant in the logic valve. 2. The pilot pressure P sub(3) and the resistance R in the pilot line have much influences on the valve operation time. 3. Spring strength have not such a severe influence on the valve operating time. 4. The operation characteristics of the logic valve can be estimated with good accuracy comparatively by numerical analysis with the equations describing poppet motion.

• Fire Science and Engineering
• /
• v.32 no.5
• /
• pp.57-66
• /
• 2018

A sports center fire in Jecheon that caused 29 deaths and 40 injuries was analyzed based on initial response and management in order to investigate the causes of the casualties. The aspects of initial response included delay of reporting 119, not being guided to the exit for the body scrubber on the $2^{nd}$ floor for escape, opening the fire doors of the exits on the $1^{st}$ floor and $3^{rd}$ floor, not closing the fire door of the main stairs on the $3^{rd}$ floor, and not doing an emergency broadcast. The management aspects included closing the alarm valve of the sprinkler system on the $1^{st}$ floor, starting-stop of the fire pump controller, neglecting leakage of water and electricity between the false ceiling and ceiling in the parking lot, hiding the exit light in the ladies bathroom lounge on the $2^{nd}$ floor and piling up things in the exit, neglecting the button of an automatic door on the $2^{nd}$ floor, conventional fire safety management, insufficient inspection of fire equipment, and not working fire shutters and smoke exhaust windows.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.322-325
• /
• 2007

This paper shows the development procedure of the low pressure LOX feed system which is used in the liquid rocket with a turbopump. Korean Air has cooperated with KARI in developing the LOX feed system to turbopump. The LOX feed system is characterized with cryogenic temperature and the thin-thickness tube for weight saving. The system in this project is composed with a main feed line and a recirculation line for the LOX temperature conditioning. Each piping system has many components, namely, bellows, filter, orifice, valves, flange and support. In this paper, system design & manufacturing, structural & thermal analyses, and component tests are explained. Finally, the system was assembled to the KARI's PTF test facility and functioned well to meet its required performance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.833-837
• /
• 2010

This study aims at finding an optimal exhaust diffuser design of a high altitude testing chamber for a low bypass turbofan engine (F404-402) with thrust pound force of 17,700 and air mass flow rate of 66kg/s ejecting at a speed of Mach 1.66. The final proposed ejector size has better pressure recovery characteristics and targets to reduce operational cost at engine performance testing. Conventional high altitude test chamber layout was adopted and first drawn in two dimensions using Autocad software so as to determine the gas path, the ejector frontal size was then determined from gas dynamics equations considering traditional gas ejection method where both the engine exhaust and cell cooling air are exhausted via the ejector. Modification to a smaller ejector with an alternative secondary cell cooling exhaust port was then performed and modelled in 3D using Solid Works software.

• Nuclear Engineering and Technology
• /
• v.25 no.1
• /
• pp.37-50
• /
• 1993

To evaluate the sequence of event and the Thermohydraulic behavior during total loss of feedwater accident and recovery procedure, a RELAP5/MOD3 calculation is performed and compared with the LOFT L9-l/L3-3 experiment. Also, the predictability of the code for the major Thermohydraulic phenomena following the accident is assessed. As a result, it is found that a pressure control using the spray until the time the water level reaches the top of the pressurizer, an overpressure protection by pressurizer PORV, a recovery of the secondary heat removal capability by refilling steam generator, and an effective cooldown by the continued natural circulation can be performed without core uncovery. It is also found that the plant-specific evaluation is necessary to confirm the effectiveness of the current symptom-oriented emergency operating procedure, especially in an overpressure protection performance and steam generator recovery performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.9
• /
• pp.774-781
• /
• 2018

In this investigation, a gas gun is proposed driven by carbon dioxide gas and installed on a quadcopter-type small unmanned drone for the purpose of cattle vaccination, and we developed a launcher and its connection unit. The system consists of a commercial drone, a gas gun, a solenoid valve, and the remote communication controller, etc. The velocity of launched projectile is measured, and the full system is finally validated through ground test and flight examination loaded for the real aircraft. The feasibility is checked if this technology is applicable to various disease abatement and hazard mitigation in the fields of agriculture and fire-fighting with the present research and development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2189-2194
• /
• 2009

The automatic hot gas by-pass technique is applied to control the capacity of refrigeration and air-conditioning system when operating at part load. In the scheme, the hot gas from the compressor is extracted and injected into the outlet of an evaporator through a hot gas by-pass valve. Thus, In this paper, the hot gas by-pass scheme for CO2 is discussed and analyzed on the basis of mass and energy conservation law. A comparative study of the schemes is performed in terms of the coefficiency of performance (COP) and cooling capacity. The operating parameters considered in this study include compressor efficiency, superheating degree, outlet temperature of gas cooler and evaporating temperature in the R744 vapor compression cycle. The main results were summarized as follows : the superheating degree, outlet temperature and evaporating temperature of R744 vapor compression refrigeration system have an effect on the cooling capacity and COP of this system. With a thorough grasp of these effect, it is necessary to design the compression refrigeration cycle using R744.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.80-88
• /
• 2018

The function of a vehicle holding device (VHD) is to securely hold a launch vehicle on the launch pad and release the launch vehicle at maximum thrust after engine ignition to allow lift-off of the launch vehicle. During the release of the launch vehicle, to prevent the Ka doing a doing a doing mode, which is the vertical oscillation of the entire liquid propellant, the release of the launch vehicle should be gradual. In this study, for the gradual release of a launch vehicle, a hydraulic system comprising an accumulator and pyro valve to operate a hydraulic cylinder and control the speed of the cylinder with an orifice is introduced. Through a test, the influence of design variables on the cylinder speed is analyzed. Based on this, the design values of the hydraulic cylinder are determined. Through this study, the engineering basis for developing a VHD releasing a launch vehicle at maximum thrust is provided.

• Journal of the Korea Society for Simulation
• /
• v.25 no.4
• /
• pp.31-42
• /
• 2016

This study aims to identify the core technology for the automatic impact of the auto-sensing breaker that is one of the construction machinery which do not have a notable development success case yet in Korea. The study has been carried out as follows. Firstly, an analysis model was developed after determining the interconnection of pressure receiving area, opening area and port. And then, a simulation of situation that hard rock and soft rock are mixed was carried out to verify if it is possible to switch between long impact mode and short impact mode continuously. Lastly, the dynamic behavior of automatic control valve induced by the change of impact mode was analyzed based on the analysis result to decipher the core principle of automatic impact control.

• Plant Journal
• /
• v.11 no.3
• /
• pp.53-63
• /
• 2015

구매자는 일반 제조업에서 자재를 피터 크랄직 매트릭스 기법에 의해 경쟁품목, 일반품목, 전략품목, 위험품목으로 분류한 후 각 품목 특성에 맞추어 구매 전략을 수립한다. 피터 클라직 매트릭스란 구매 리스크와 비즈니스 영향도 즉 특정 품목의 구매 금액 비중에 따라 자재를 분류하는 기법이다. 본 논문은 플랜트 엔지니어링산업에서 플랜트 기자재를 대상으로 피터 클라직 매트릭스 기법에 의해 기자재를 분류한 후 각 품목 특성에 맞는 구매 전략을 제안하고 사례 기업인 A사가 사우디아라비아에서 수행하는 발전 플랜트 기자재에 제안한 구매 전략을 적용하여 그 효과를 검증한 것이다. 플랜트 엔지니어링산업은 수주산업인데 총 수주금액 중 구매가 차지하는 비중은 약 50~60%이다. 따라서 프로젝트를 수행할 때 원가를 절감하여 이익을 극대화하기 위해 구매는 매우 중요한 역할을 한다. 플랜트 기자재는 크게 회전기계류, 고정장치류, 전기자재류, 제어자재류, 배관자재류로 구분된다. 각 공종별 플랜트 기자재에 대해 구매 지출 분석을 한 후 피터 클라직 매트릭스 기법에 의해 플랜트 기자재를 분류한 결과 경쟁품목에는 열교환기, 저장탱크 등이 포함되었고 일반품목에는 전선관, 조명기자재, 밸브 등이 포함되었다. 또한 전략품목에는 가스터빈, 가스터빈 흡입공기 냉각장치 등이 포함되었고, 위험품목에는 가스터빈 고정 볼트 등이 포함되었다. 경쟁품목 중 다관형 열교환기는 공급자와 공동으로 원가 모델을 구축하는 전략을 수립했고 저장탱크의 경우에는 공급자에게 원자재를 사급하는 전략을 수립하였다. 그 전략을 A사가 수행하는 프로젝트에 적용한 결과 각각 20%와 6%의 원가 절감 효과를 얻었다. 일반품목 중 전선관은 구매 대행사를 활용하는 전략을 수립했고 조명기자재는 기술 사양 검토 과정을 생략한 구매 프로세스 간소화 전략을 수립하였다. 그 결과 약 10%의 원가 절감과 평균 5일의 발주기간을 단축할 수 있었다. 전략품목 중 가스터빈 흡입공기 냉각장치는 공급자와 포괄적 양해각서를 체결하여 공동으로 사업주에 대응하는 전략을 수립했고 그 결과 프로젝트 수행 안정성 확보와 공급자 조기 참여를 통한 발주 스케줄 단축을 이룰 수 있었다. 위험품목 중 가스터빈 고정볼트는 재고 확보 전략을 수립하여 자재의 부족이나 파손으로 인해 프로젝트 공기에 영향을 주지 않도록 리스크를 감소시키는 효과를 얻었다.