• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.08a
• /
• pp.101-104
• /
• 2000

본 논문은 FLC를 이용한 원격제어 이동로봇이 다수 목적지를 보다 효율적으로 주행하도록 제어하는 것이다. 원격 제어 이동로봇이 전진, 후진, 좌회전, 우회전의 이동 명령을 한 가지씩 수행한 후 멈추는데 발생되는 단점을 보완하기 위해 본 논문은 초음파 센서를 이용하여 얻어진 지형정보를 바탕으로 목적지에 대한 경유점 수를 줄이면서 경유점 간의 이동을 최적한 경로로 주행을 할 수 있도록, 퍼지 논리 제어기를 이용하여 보다 효율적인 제어를 할 수 있는 알고리즘을 연구하였다. 그리고, 이러한 주행 알고리즘을 시뮬레이션을 통해 확인하였다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.99-104
• /
• 2010

We introduce Internet TCP/IP control system to monitor the traffic volume on the traffic network system. To check the traffic volume on traffic road, we use the traffic detector system shppe of circle or diamond or rectangular. Nevertheless we use traffic detector, we will use internet addressin TCP/IP system. If we use TCP/IP control system, we acquire many good point, we achive high sircurity and low costness traffic monitoring system coming difficulty and high level position. But internet system is very easy and low cost direction. Traffic control system is very more depending on the high techinquesion and very complexity. Therefore we introducing TCP/IP internet addressing control system schemetic point.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.3
• /
• pp.27-36
• /
• 2000

A higher order panel method based on B-spline representation for both the geometry and the velocity potential is developed for the solution of the flow around two-dimensional lifting bodies. Unlike Lee/Kerwin, who placed multiple control points on each panel and solved the overdetermined system of equation by the least square approach, the present method places only as many number of control points as required by the unknowns of the problem. Especially, a null pressure jump Kutta condition at the trailing edge is found to be effective in stabilizing the solution process and in predicting the correct solution. The new approach, is validated to be accurate through comparison with the analytic solution for a 2-D airfoil and to be less time-consuming due to fewer number of panels required than that used in Lee/Kerwin.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.1 s.307
• /
• pp.13-20
• /
• 2006

In this paper, we propose a motion control scheme of robot manipulators based on visual feedback under camera-in-hand configuration. The desired joint velocity and acceleration for motion control is made by the feature-based visual data in the outer loop. The control input for tracking feature points on the image plane uses robot kinematics dynamic. The proposed control input consists of the image feature and the joint velocity error to achieve robustness to the parametric uncertainty. The stability of the closed-loop system is proved by Lyapunov approach. Computer simulations and experiments on a two degree of freedom manipulator with 5 links are presented to illustrate the performance of proposed control system.

• ICROS
• /
• v.3 no.5
• /
• pp.12-16
• /
• 1997

조립 작업시 사람이 이용하는 방법을 수학적으로 구현한 미세외란/상관관계에 기초하여, 이의 기본 원리와 응용에 대하여 살펴보았다. 이 방법의 가장 큰 특징은 기존의 이치 제어기에 외부 궤환 제어기를 첨가함으로써 힘에 의하여 안내되는 제어기로 구조를 개선할 수 있다는 점이다. 이러한 제어기를 갖는 로봇을 열 교환기 조립작업에 응용한 예를 들었으며, 로봇을 이용한 다른 조립 작업에도 매우 유용하게 사용될 수 있으리라 생각된다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.5
• /
• pp.525-532
• /
• 2004

Telemanipulator is distingushed from industrial robot by iterating same specified work. Manipulator operator is included in control loop for controlling the telemanipulator because he decide directly during the work and order controllabily. We implement fuzzy controller for reducing the modelling error of telemanipulator which depend on the PID controller. But position-force control method of bidirectional control impose unsafety of vibiration and Analytic Hierchy method can stabilize for reducing nonlinear modelling error by expert operator because of transformation empirical control rule to linear model.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.25 no.3
• /
• pp.117-123
• /
• 2019

The general Impulse Sealer has a problem of sealing quality because continuously sealing process results in an undesirable temperature rise, which may accumulate the heat during the operation. In order to address such a drawback, the controlled sealing temperature method can be effectively utilized compared with the general controlled time method. As such, a temperature sensor with capability of detecting the sealing temperature was installed, and a separate PCB was manufactured to control the sealing temperature by measuring and calculating the detected temperature. The temperature changes during the temperature rise and maximum temperature after continuously operation were investigated using an Impulse Sealer system. Next, the results obtained from experiment were compared with each other. As such, the maximum temperature was 70.3℃, whereas 8.9℃ was recorded as control temperature. It implies that this controlled temperature system prevented the undesirable temperature rise, thereby causing a consistent sealing quality.

• Journal of Korean Society of Forest Science
• /
• v.111 no.2
• /
• pp.287-301
• /
• 2022

This study aims to propose a crane-tip control method to intuitively control the end-effector vertically or horizontally for improving the crane work efficiency and to confirm the control performance. To verify the control performance based on experimental variables, a laboratory-scale crane was manufactured using an electric cylinder. Through a forward and reverse kinematics analysis, the crane was configured to output the position coordinates of the current crane-tip and the joint angle at each target point. Furthermore, a method of generating waypoints was used, and a dead band using lateral boundary offset (LBO) was set. Appropriate parameters were selected using bang-bang control, which confirmed that the number of waypoints and LBO radius were associated with positioning error, and the cylinder speed was related to the lead time. With increased number of waypoints and decreased LBO radius, the positioning error and the lead time also decreased as the cylinder speed decreased. Using the proportional control, when the cylinder velocity was changed at every control cycle, the lead time was greatly reduced; however, the actual control pattern was controlled by repeating over and undershoot in a large range. Therefore, proportional control was performed by additionally applying velocity gain that can relatively change the speed of each cylinder. Since the control performed with in a range of 10 mm, it was verified th at th e crane-tip control can be ach ieved with only th e proportional control to which the velocity gain was applied in a control cycle of 20 ms.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.4
• /
• pp.323-332
• /
• 2004

Sound localization can be controlled by simulating the transfer functions from sound source to listener's ears. Even by using this method. a good performance cannot be expected when a listener slightly moves from the position where the transfer functions were measured. We have already been proposed the multi-point control method to overcome the problem of the listener's small movement. In this method, the transfer functions are simulated at multiple points around the listner's ears so that the points forms an area which covers the small movement of the listener. In this paper. we investigated the effect of applying multi-point control method for the control of sound localization. Results show that multi-point control is effective to keep the perceptual error of the localized direction small when the listener moves up to 6 cm from the original position.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.4
• /
• pp.324-324
• /
• 2004

Sound localization can be controlled by simulating the transfer functions from sound source to listener's ears. Even by using this method. a good performance cannot be expected when a listener slightly moves from the position where the transfer functions were measured. We have already been proposed the multi-point control method to overcome the problem of the listener's small movement. In this method, the transfer functions are simulated at multiple points around the listner's ears so that the points forms an area which covers the small movement of the listener. In this paper. we investigated the effect of applying multi-point control method for the control of sound localization. Results show that multi-point control is effective to keep the perceptual error of the localized direction small when the listener moves up to 6 cm from the original position.