• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.30-34
• /
• 1996

자동차용 마찰재의 원료로 사용되는 고체 윤활제($Sb_{2}S_{3}$)와 연마재(ZrSiO$){4}$)의 상대량이 다른 3가지의 마찰재를 제조하여 그들의 마찰특성을 자동차용 Brake Dynamometer를 사용하여 연구하였다. 각각의 마찰재에 관하여 자동차 제동시에 나타나는 마찰계수의 변화와 Torque 변화 그리고 시험후의 마찰재와 rotor의 마모량을 측정하였다. 제동특성과 직접 관련 있는 것으로 알려져있는 마찰계수의 안정성은 $Sb_{2}S_{3}$이 상대량이 높을 때 좋은 특성을 나타내었으며, 반면에 ZrSiO$_{4}$의 상대량이 많은 경우에는 마찰계수의 안정성이 저하되었을 뿐 아니라 제동시의 torque 변화량도 증가하여, 자동차의 Judder현상을 해결하는데 좋지않은 경향을 나타내었다. 이는 마찰시에 계면에 형성되는 윤활막의 거동에 의한 현상이며 이때 마찰재 및 상대재의 마모량은 연마재의 양이 증가함에 따라 마모량이 증가 하였다.

• Journal of the Korean Society for Railway
• /
• v.20 no.1
• /
• pp.1-10
• /
• 2017

Brake squeal noise has been a challenging problems for a long time. It is very annoying to passengers and residents near tracks. Two methods have been applied to reduce or eliminate brake squeal noise. One is to improve frictional materials; the other is to optimize the topology and structures of brake pads. In this study, we developed two kinds of brake pads; one is a pad whose frictional material is different from the KTX brake pad friction material; the other is a flexible pad that has the same frictional material as that of the KTX brake pad, but a different structure. Squeal noise and friction coefficients were measured and analyzed using a full-scale brake dynamometer. It was found that the dynamometer test can simulate the squeal noise of KTX trains at stations. The squeal frequency of the KTX at 4500Hz was exactly reproduced; this value of 4500Hz was one of the natural frequencies of the KTX brake disc. It was also found that the squeal noise depended on the caliper pressure, initial disc temperature and braking speed. The average friction coefficient was 0.35~0.45. The new pad lowered the squeal noise by 17.3~21.6dB(A).

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2080-2093
• /
• 2008

Disk brake system take charge of maximum braking energy among the mechanical brake systems for high speed train. For this reason, Metallic friction materials and heat resistant steel disk is adopted at disk brake system for high speed train. It was investigated tribological characteristics(friction coefficient, friction stability, wear rate and braking temperature) between some kinds of metallic friction materials and heat resistant steel disk. Cu-based friction material for high speed train have suitable tribological characteristics.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.253-261
• /
• 2013

According to the measured results of KTX brake squeal noise in this study, high level brake noise occurred in a wide frequency range, 100~18,000Hz. To identify the sources of the brake squeal noise, unstable vibration modes due to brake disc/pad interaction were analyzed under various conditions by the finite element method. Complex eigenvalues for a brake unit with a disc and four pads were obtained. It was found that the real parts of the complex eigenvalues, that is, unstable vibration modes, were closely related to friction coefficients, pressure on the brake cylinders, elastic moduli of the components, and other conditions.

• Journal of the Korean Society for Railway
• /
• v.11 no.2
• /
• pp.188-194
• /
• 2008

Brake disks for rolling stock are exposed to thermal fatigue during braking, and thermal cracks occur on surface of disks. Thermal cracks can cause serious accidents, deterioration of braking performance and increase of maintenance cost due to frequent exchange of friction materials. In this study, candidate materials with high-heat resistance were selected by searching the literature. By using cast specimens made of the candidate materials, chemical composition, crystal structure and graphite type were analyzed. In addition, friction coefficient and wear were measured and compared with values for the disk material in service. As a result, it was shown that the NiCrMo has highest tensile strength and lowest friction coefficient and the disk material in service has the most stable friction characteristics.

• Journal of the korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.41-46
• /
• 1994

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.41-47
• /
• 1994

An optimal brake pad must have stable friction, low wear and least amount of squeal. In this study, the friction, wear and squeal behavior of some non-asbestos Kevlar materials have been evaluated experimentally. Four specimens with different formulations and a pin-on-disk machine were used for this study. To determine the role of each component in friction and squeal of a brake pad, statistical correlations have been obtained and discussed. The components tested were : Kevlar, Steel Powder, Barium Sulfate and fillers combined by Resin.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.10-19
• /
• 1997

Frictional characteristics of two different types of automotive friction materials were studied. They were non-asbestos organic and semi-metallic friction materials. The two friction materials were tested using an inertial brake dynamometer to investigate friction stability, rooster tailing phenomena, temperature change during drags and stops. Results show that the level of the friction force is strong functions of time, temperature, and speed regardless of the type of friction materials. In particular, rooster tailing effects are pronounced in the case of semi-metallic friction materials compared to non-asbestos organic friction materials. The phenomena appear strongly dependent on raw materials contained in the friction materials.

• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.72-80
• /
• 2009

The tribiological characteristics such as friction coefficient, friction stability, wear rate and braking temperature between various types of metallic friction materials and heat resistant steel disk, were investigated by using lab-scale dynamometer. Friction materials for high speed train have higher friction coefficient and friction stability as compared to aircraft friction materials even though friction materials for high speed train have lower wear rate. In addition. Cu-matrix friction materials have higher temperature increase rate than Fe-matrix friction materials. All friction surfaces have Fe-base oxide layer after completing test.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.786-791
• /
• 2007

Korean high speed train(HSR-350x) has adopted a combined electrical and mechanical(friction) braking system. Brake blending control unit(BBCU) controls each brake system to fulfill the required brake performances such as braking distance, deceleration and jerk. Also the braking system should be designed considering the economical management, such as effective use of generated braking energy and the minimum wear of friction materials(a pad and a brake shoe). In this paper, we establish the disc braking force pattern that reduces the wear of pad in the disc braking system by minimizing the variance of the instantaneous disk baking energy during braking time, and compare the wear mass of pad between the conventional disc braking force pattern and the established results.