• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.238-238
• /
• 2003

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.219-225
• /
• 2000

This study is to develop a Fe-based disc brake lining with sponge structure for rolling stock of 150km/h train and to concept design with 3 groove type for brake disc reducing hot hair-crack and certainly friction coefficient. The developing brake lining would be to presumption of saving 300 million won during one year

• Tribology and Lubricants
• /
• v.27 no.2
• /
• pp.95-100
• /
• 2011

The brake disc materials for railway vehicle have been mainly used cast-iron. The brake disc and pad should be light, resist to a thermal crack and absorb enough friction energy. In order to satisfy this requirement, aluminum alloy brake disc for railway vehicle has been newly developed. The aluminum itself has not been considered the friction material for railway vehicle. However, in the case of aluminum composite with dispersed ceramic particles, friction characteristics, resistance to wear and heat are much improved. In the present study, aluminum composite brake disc of 20% ceramic particle and three kinds of organic pads have been tested in dynamometer. The results show that Al MMC brake disc and pad have good friction coefficient and wear rate, and thermal cracks in brake disc have not been initiated. Also, the Al MMC brake disc can be applied to railway vehicle of 150 km/h.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.2
• /
• pp.87-94
• /
• 2012

Mechanical break system used in train, that mixed air break & electronic break system. this system suggest lots of ways for modify efficiency and solution of environmental problems due to recently intend to green growth. The mechanical break system has environmental & economical problem. Environmental sides(problem) are dust and noise etc and economical sides(problem) are replaced the spare parts that are breaking shoe and lining ect. For compensate those kind of weak points, we needs a wide territories of electronic break which is from high speed range to stop. This research is estimated the load torque due to an incline and stop the train method also check the characteristic of stop the train to estimate a torque follow the sharp drop.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.43-48
• /
• 2005

In order to facilitate technical exchange among nations and/or institutes through the establishment of mutual recognition and the reliability guarantee of testing results by testing standards standardization, the interlaboratory comparison tests on brake discs and linings between KRRI and CARS were conducted. So far, two ways of comparison tests were performed for a better understanding of mutual recognition and standardization in railroad brake linings between Korea and China. In this paper, the first and second comparison testing results have been summarized, and the suggestions for the future research work are also presented to encourage extensive research on comparison study of railroad brake discs and linings between KRRI and CARS. Eventually, the final goal of the current research will be the establishment of standardization of railroad testing standards.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.665-669
• /
• 2007

This study investigates the temperature change and thermal conductivity for the braking disc of the railway vehicle due to the types of train and service conditions. The temperature change was measured by non-contact Infrared thermometers. Average temperature was measured between $79.32^{\circ}C$ and $104.46^{\circ}C$ due to types of train and service section. In the same service section, the surface temperatures of Saemaul train were higher than Mugungwha train; the reason might have been the average service speed of Saemaul train (83km/h) was higher than Mugungwha train (107km/h), and the weight was similar 39t (Mugungwha) and 39.3t (Saemaul). But the maximum surface temperature was measured on the Mugungwha train; however the difference was not too big with the maximum temperature of Saemaul train. Also, the disc surface temperatures were changed due to the material of lining; metal and non-asbestos, on the same train and the same service section. In addition. the thermal conductivity was tested the thermal conductivities were increased by the increasing of the temperature. The change is too big between $100^{\circ}C$ and $200^{\circ}C$. But each average value is small. and the mechanical property change is very low. As a result, we conclude that this disc is suitable for usage between $100^{\circ}C$ and $300^{\circ}C$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.55-58
• /
• 2005

During braking at a train, thermal energy is generated due to the frictions between disk and lining and wheel and shoe. In general, the braking transfers the kinetic energy into thermal energy. Therefore, the frictional characteristics are varied according to the braking force, the thermal resistance, and the thermostable, etc. Using a Dynamo testing we have studied the frictional characteristics and the thermal distribution to investigate a stable speed and to improve the testing method through comparing and analysing in the measurement of the thermocouple temperature and infrared camera.

• The tire
• /
• s.69
• /
• pp.12-16
• /
• 1977

타이어의 실노면상에서의 트랙션성능을 측정, 평가하는것은 자동차의 발진, 가속, 제동 및 시회성능의 점으로브터 중요하면 이것을 측정하기 위해서 타이어 트랙션시험차를 개발했다. 이시험차는 타이어의트랙션성능을 미끄럼율과제동, 구동계수의 관계, 횡화각과 사이드포오스계수, 어라이닝토루크의 관계로 측정되는 특장을 갖는다. 이시험차를 이용해서, 건조및 습윤아스팔트노상과 설노상에서의 트랙션성능에 대한 타이어트랫드의 기본적 페턴의영향을 측정한 결과, 다음과 같은 지견을 얻었다. (1)도로의 상태의 상위에 의한 타이어트랙션 성능은 건조상태에선 습윤상태보다 크며 노설상에선 전양자보다 훨씬 작다. (2)트랫드의 종방향의 구본수의 영향에 대해선 여하한 노면상태에서든 구본수가 증가한만큼 트랙션성능은 증가하나 어느구본수에선 포화하는 경향이 있다. (3)설노상에서의 트랫드의 구각도에 대해서는 구의각도가 타이어의 진행방향에 대해서 직각의 페턴이 좋다고 할 수 있다.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.586-591
• /
• 2003

This paper describes the result of proficiency testing by inter-laboratory comparisons for braking lining. Proficiency testing provides an objective means of assessing and demonstrating the validity and reliability of test results produced by laboratories. To more accuracy comparison test for braking lining test, they will be made the same test procedure and environment conditions.

• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.269-274
• /
• 2011

The purpose of this paper is to study and analyze the improvement method for the failure examples including the vehicle brake system in actual field. It was verified that the indicator plate of pad wear scratched the brake disk because of wearing after displacement of non- identification parts pad. The caliper of other vehicle was installed with brake system verified the phenomenon produced groove in center point because of one side wear when the pad was not fully contacted with the rub disk by other action surface pressure and pad action condition. It verified that the crack phenomenon fatigue was produced by brake thermal deformation because of decreasing the thickness by grinding to modify the non-uniformed wear of brake disk. It verified that the friction sound was produced by the friction phenomenon because of non-uniformed contact of lining and an alien substance with inner of the drum and lining braking by crack phenomenon with brake drum surface.