• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.480-493
• /
• 2007

Many railway-advanced countries are using the various types of track to reduce the track maintenance and repair cost according to the improvement of velocity. It spends on much maintenance and repair cost for ballast track due to abrasion of ballast, track irregularity and unisotropical ballast-support stiffness. The ballast track on railway bridge is accelerating the deterioration of ballast according to interaction of railway bridge and track. As continuing the deterioration, it is caused dynamic loads. Due to these effects, it increases negative loads of track and bridge. However, when designing the railway bridge, the effect of ballast track was applicate only dead load, so elastic behavior effect of ballast track is not influenced. Therefore, this paper presumes the stiffness of ballast track on railway bridge considering dynamic behavior of railway bridge, it was evaluated that effect on dynamic behaviors of railway bridge according to ballast track stiffness.

• The Journal of the Petrological Society of Korea
• /
• v.10 no.3
• /
• pp.179-189
• /
• 2001

The determination of trace concentration of U, Th and Pb was carried out for chemical dating of zircon and monazite by electron microprobe. Detection limit and error range should be considered to measure characteristic X-rays of M-line from those minerals, which are low in the ionization of atom and low peak intensity in the spectrum. The element of U, Th and Pb were simultaneously measured with 3 spectrometers equipped with PET crystal to reduce a total counting time and error due to drift of instrumental operating condition. Detection limit could be improved from increase of the peak/background ratio through adjusting pulse height analyzer about 1000 mv baseline. Under permissible maximum analytical conditions, theoretical detection limit of U, Th and Pb is down to 30 ppm (99% confidence level). The analytical result was maintained at a relative error $\pm$10% ($2{\sigma}$) in 800 ppm Pb, $\pm$5% ($2{\sigma}$) in 2330 ppm U and $\pm$10% ($2{\sigma}$) in dating from a single measurement of zircon at 15 keV and 100 nA. However, for the precise dating of zircon and monazite, if it is considered a 3 $\mu\textrm{m}$ spatial resolution, <100 ppm ($3{\sigma}$) detection limit and <$\pm$10% ($2{\sigma}$) relative error, optimum analytical conditions are given as 15~20 keV accelerating voltage, 100~200 nA beam current and 300~1200 sec total counting time. To reduce material damage by high current, there is need to be up to 3~5 $\mu\textrm{m}$ of electron beam diameter, or to use arithmetic average of multiple measuring at a shorter counting time. A younger or relatively low concentration rocks can be dated chemically by lower detection limit and improved precision resulted from increase of current and measuring time.

• Korean Security Journal
• /
• no.14
• /
• pp.367-388
• /
• 2007

Some of individuals working at various fields of security guard are given the legal right to use a gun to cope with expected risks and crimes. Not only in Korea but also throughout the world, a pistol is being used as a device for the workers of security guard such as the army, the police and intelligence agencies to keep the law and social order. A pistol, which is regarded as the last safety measure of security guard, is easy to carry but, because of its short barrel for high portability, its hit ratio and long-range shooting performance are much lower than ordinary guns. Despite such weak points, a pistol can be a great tool because of its high portability and if the users make steady efforts to improve their skills and, for this reason, it has been being used widely until now. National agency workers' pistol shooting skills depend on several important factors, but for the fast and accurate shooting, the mot important factor is how to aim at the target. Because it takes a relatively longer time to align the sight on the target, the change of the sight alignment method is expected to improve pistol shooting skills a lot. In Korea, however, most of national agency training centers teach the basic aiming method that crosses the foresight and the backsight and aligns the crossing to the target. That is, they teach the sight alignment method for fixed targets. Some agencies in Korea and foreign countries that have used guns more frequently and longer than us are teaching different sight alignment methods as well. Representative ones of them are aiming only with the foresight and pointing shooting. These aiming methods are expected to produce good results against moving targets. While the basic sight alignment method has to cross the foresight and the backsight and then to align the crossing to the target, so takes a longer time than other aiming methods, the other two aiming methods are expected to be effective in fields where both swiftness and accuracy are require. Because domestic agencies are teaching mainly the basic sight alignment method, the present study purposed to examine the effects of different aiming methods on shooting records and ultimately to contribute to national agency workers' operation. For this purpose, we selected 20 policemen from local police commandos under the National Police Agency who were accustomed to pistol shooting and measured their pistol shooting. According to the results, the pointed shooting method showed the best record in 5m short.range shooting. As to hit ratio in 15m shooting, which is relatively long.range for pistol shooting, the basic aiming method showed the best record, but the results of statistical analysis showed that pointed shooting is most superior. Of course, the results were obtained from a group who were used to and skillful in pistol shooting, but they are considered meaningful in that all the police and national agency workers should have such high shooting skills.

• Food Science of Animal Resources
• /
• v.27 no.2
• /
• pp.179-184
• /
• 2007

The objective of this study was to investigate the contents of meat and non-meat ingredients, calorie, fatty acid composition, and cholesterol contents of processed meat products of which informations are being provided for consumer and partly required for the current labeling system in Korea. A total of sixty-one domestic processed meat products produced from 6 domestic meat companies were collected at the large supermarkets in Suwon city; 1) 31 ham products(3 loin hams, 6 press hams, 20 mixed press hams and 2 fish hams), 26 sausage products(15 pork sausages, 7 mixed sausages and 4 fish sausages) and 4 ground processed meat products. Soy protein and com starch were widely used as non-meat ingredients for the most of processed meat products. The contents of meat, protein, fat, cholesterol contents, and calories were 75-98, 12-23, 1-16%, 7-50 mg/100g, and 1,620-3,127 cal/g for ham products and 60-96, 5-17, 3-27%, 5-73 mg/100g, and 1,271-3,546 cal/g for sausage products, respectively. The saturated(SFA), monounsaturated(MUFA) and polyunsaturated fatty acids(PUFA) contents of ham products were 31-40, 44-53 and 60-72%, and those of sausage products were 17-38, 34-61, and 13-37%, respectively. The ranges of meat contents and nutritional compositions were considerably broad even in the same type of the meat products. Therefore, the labeling system of the nutritional facts for ham as well as sausage products is necessary to categorize the quality level and thus to give the nutritional information to consumer for better choice of products in market.

• Tuberculosis and Respiratory Diseases
• /
• v.66 no.4
• /
• pp.288-294
• /
• 2009

Background: A lung hyperinflation, or air trapping, caused by expiratory flow-limitation contributes to dyspnea in patients with chronic obstructive pulmonary disease (COPD). Forced expiratory volume in 1 second ($FEV_1$) has served as an important diagnostic measurement of COPD, but does not correlate with patient-centered outcomes such as dyspnea. Therefore, this study was performed to investigate the role of radiologic quantity in evaluating the dyspnea in patients with COPD by measuring lung hyperinflation in chest x-ray and high resolution chest tomography (HRCT). Methods: Fifty patients with COPD were enrolled in this study. Their subjective dyspnea score (modified Borg scale dyspnea index), spirometry, and lung volume were measured. Simultaneous hyperinflations of chest x-ray score ("chest score") and degree of emphysema of HRCT ("HRCT score") were measured. The "chest score" were composed of lung length, retrosternal space width, and height of the arc of the diaphragm and "HRCT score" were composed of severity and extent of emphysema. Results: The mean age of patients was 69 years old and their mean $FEV_1$ was 51.7%. The Borg score significantly correlated with parameters of spirometry and lung volume, including FVC, $FEV_1$, $FEV_1$/FVC, RV, RV/TLC, and DLCO. The Borg score correlated well with "HRCT score", but did not correlate with "chest score". Also, the Borg scale correlates inversely with body mass index. Conclusion: The quantity of emphysema on chest HRCT may serve as an objective marker of dyspnea in patients with COPD.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.87-97
• /
• 2016

This work proposes a time-shared 10b DAC based on a two-step resistor string to minimize the effective area of a DAC channel for driving each AMOLED display column. The proposed DAC shows a lower effective DAC area per unit column driver and a faster conversion speed than the conventional DACs by employing a time-shared DEMUX and a ROM-based two-step decoder of 6b and 4b in the first and second resistor string. In the second-stage 4b floating resistor string, a simple current source rather than a unity-gain buffer decreases the loading effect and chip area of a DAC channel and eliminates offset mismatch between channels caused by buffer amplifiers. The proposed 1-to-24 DEMUX enables a single DAC channel to drive 24 columns sequentially with a single-phase clock and a 5b binary counter. A 0.9pF sampling capacitor and a small-sized source follower in the input stage of each column-driving buffer amplifier decrease the effect due to channel charge injection and improve the output settling accuracy of the buffer amplifier while using the top-plate sampling scheme in the proposed DAC. The proposed DAC in a $0.18{\mu}m$ CMOS shows a signal settling time of 62.5ns during code transitions from '$000_{16}$' to '$3FF_{16}$'. The prototype DAC occupies a unit channel area of $0.058mm^2$ and an effective unit channel area of $0.002mm^2$ while consuming 6.08mW with analog and digital power supplies of 3.3V and 1.8V, respectively.

• Journal of Korean Home Economics Education Association
• /
• v.32 no.3
• /
• pp.97-110
• /
• 2020

The purpose of this study is to develop milk education materials for adults based on the scientific basis of right milk consumption in the format of card news that can be easily accessed on a mobile phone or the internet and has high impact. The topics to be included in the card news were selected based on the findings from literature analysis and focus group interviews with 10 adults(32.0±6.4 years). For the eight selected topics, effective communication was made by suggesting some information that users want to know while reflecting adult eating habits, lifestyle habits, and nutrition and health interests. The card news draft was reviewed by researcher and consulting experts, and then questionnaire survey was conducted using Likert 5-point scales by 50 adults(42.7±10.2 years). Based on the results of the review, consultation and questionnaire survey, a final draft of the card news consisting of 11 cuts was completed. Card news proposal is expected to produce educational effects, since the respondents showed high satisfaction with the card news (higher than 4 on the 5-point scales) according to the questionnaire survey. Adults can easily access and use the card news developed in this study, and thus this card news is expected to increase milk consumption in adulthood and improve nutrition and health through friendly and systematic milk education.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.6
• /
• pp.657-665
• /
• 2019

In this study, we conducted a study on the transcranial magnetic electrode, a method for the study of dementia and muscle pain, a neurodegenerative disease caused by an aging society, which is becoming a problem worldwide. In particular, transcranial magnetic electrodes have been studied to improve their ability to be deteriorated by dementia symptoms such as speech, cognitive ability, and memory by outputting magnetism deep into the brain using coils on the head epidermis. In this study, simulation was performed using Maxwell 3D program for the design of coil, the core of transcranial magnetic electrode. As a result of the simulation comparison between the coil designed by the previous research and the coil through the research and development, the output was found to be superior to the conventional designed coil. The graphs of the coil outputs of B-Field and H-Field are found to be symmetrical, but the symmetry between each coil is pseudo-symmetrical and not accurate. Based on these results, an experiment was conducted to confirm whether the output of the head epidermis through both coils is possible. In the magnitude field of the reverse-coil 2-coil analysis, the maximum output was 3.3920e + 004 H [A_per_meter], and the vector field showed the strongest magnetic field around 35 to 165 degrees. It was confirmed that the magnetic output canceled due to the magnetic output. In the case of the forward 2-coil, a maximum of 3.2348e + 004H [A_per_meter] similar to the reverse coil was observed, but in the case of the vector field, the magnetic output regarding the forward output and the head skin output was confirmed. However, when the height change in the output coil, the magnetic output was reduced.

• Journal of Yeungnam Medical Science
• /
• v.17 no.1
• /
• pp.55-65
• /
• 2000

Purpose: To compare the efficacy, predictability, stability and safety of excimer laser photorefracive keratectomy(PRK) for myopia and photoastigmatic refractive keratectomy(PARK) for compound myopic astigmatism. Methods: Two-hundred and three eyes(l18 eyes < -7D spherical equivalent, 85 eyes ${\geq}$ -7D spherical equivalent) received excimer laser correction for compound myopic astigmatism and 152 eyes(116 eyes < -7D, 36 eyes ${\geq}$ -7D) for simple myopia. A VISX 20/20B $VisionKey^{TM}$ excimer laser was used to perform either PARK or PRK. Visual acuity with and without correction, refraction, IOP, corneal haze, and topography were evaluated at 1, 3, 6, and 12 months postoperatively. All patients were followed up for more than 12 months. Results: Postoperative refraction were generally stable after 3 months without significant early overcorrection. At 12 months, 110(94.8%) eyes that underwent PRK and 104(88.1%) eyes that underwent PARK achieved UCVA of 20/30 or better in the group who had lower than -7D correction. For eyes treated with -7D or more, these figures were 31(86.1%) eyes after PRK and 57(67.1%) eyes after PARK. The incidences of within 1D of plano refraction at 1 year follow-up were 97.4% after PRK and 93.2% after PARK in the group who had lower than -7D correction. For eyes treated with -7D or more, these figures were 80.6% after PRK and 70.6% after PARK. Conclusions Myopia with or without astigmatism was successfully treated in most of the eyes using PRK or PARK with VISX 20/20B $VisionKey^{TM}$ excimer laser. The predictability and stability of the postoperative refraction during the first 12 months seem to be quite reliable. Further improvement of excimer laser system and software should increase the clinical outcomes and safety of refractive procedures.

• Journal of the Korean Arthroscopy Society
• /
• v.7 no.2
• /
• pp.169-175
• /
• 2003

Purpose : The purpose was to evaluate the early result of revision of failed anterior cruciate ligament (ACL) reconstruction. Materials and Methods : From August 1997 to February 2002, this report presents the findings of 18 patients who had revision surgery for failed ACL reconstruction. There was an average of 39 $(7\~120)$months from index procedure to the time of revision. Allografts were used in 14 $(78\%)$cases and autografts were used in 4 $(22\%)$cases and the revision procedures were assisted by arthroscopic technique. The majority of chief complaints were instability in 16 $(89\%)$cases. Sixteen $(89\%)$ cases had 1 previous reconstruction, 2 $(11\%)$ cases had 2. Before and after revision, patients were evaluated by Lachman test, pivot shift test, KT 2000, radiographs, Lysholm score and HSS score and subjective satisfaction. Results : Average length of followup was 27 $(12\~60)$months. Preoperatively, all cases were positive in Lachman test and pivot shift test. After revision the majority of cases were negative. Objectively improving stability was confirmed by KT 2000 and all average KT 2000 was 7.75 $(3.5\~12.5)$mm preoperatively and 2.36 $(1.0\~6.0)$mm at final followup. Lysholm score and HSS score were also improved from 72.6 $(66\~77)$ and 72.5 $(68\~78)$ preoperatively to 89.2 $(80\~92)$ and 88.2 $(81\~92)$ at final followup. Most $(89\%)$ of patients were satisfied with their results. The most common causes of failed ACL reconstruction were malposition of femoral tunnel in 11 $(61\%)$cases. Conclusion : Arthroscopic revision ACL surgery with adequate graft for failed ACL reconstruction was successful in objectively and subjectively improving stability. However, considering the most common causes of failure after ACL reconstruction were errors in surgical technique, it is important that the primary ACL reconstruction should be performed with correct surgical technique.