• Journal of ILASS-Korea
• /
• v.11 no.1
• /
• pp.7-16
• /
• 2006

Performance of thin films fabricated with the electrostatic spray deposition (ESD) technique is strongly governed by surface morphology, which depends on deposition parameters such as deposition time and temperature, solution properties, and surface characteristics of substrates. In this article, the state of the art on the relationships between the surface morphology and the deposition parameters is presented. Also studies on the electro-hydrodynamic atomization process and the motion of drops relevant to the ESD technique are briefly reviewed, and the future research works are suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.133-138
• /
• 2000

MgO thin films were deposited using $Mg(tmhd)_2$ as a precursor dissolved in a solvent by electrostatic spray pyrolysis. When a pure tetra hydro furan was used as a solvent, a large number of particles appeared on the MgO thin film surface due to homogeneous nucleation. However, by adding 1-butyl alcohol or 1-octyl alcohol to THF, homogeneous nucleation was restricted and the number density of the large particles was also drastically reduced. X-ray diffraction analysis showed that the MgO films had a (100) preferred orientation regardless of the type of solvents used. Characterization using Fourier Transformed-Infrared and spectroscopic photometer revealed that the crystallized MgO thin films on the glass substrate had a high optical transmittance (> 85 %) in the visible range. Discharge characteristics of MgO thin films deposited by ESP method on an alternating-current plasma display panel were compared with a MgO thin film prepared by reactive radio-frequency planar magnetron sputtering.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1111-1120
• /
• 1998

Spray Drying Absorber(SDA) system, where the combustion product gas is mixed with atomized limestone-slurry droplets and then the chemical reaction of $SO_2$ with alkaline components of the liquid droplets forms sulfates, has been widely used to eliminate $SO_2$ gas from coal fired power plants and waste incinerators. Liquid atomization is necessary because it can maximize the reaction efficiency by increasing the total surface area and dispersion angle of the alkaline components. First, numerical calculations using FLUENT are carried out to investigate $SO_2$ concentration distribution and thus to calculate $SO_2$ removal efficiency. So to attain the optimized spray conditions, then an electrostatic spraying system is set up and spray visualization is performed to show the effect of an electric field on overall droplet size. Next, the effect of an electric field on the concentrations of $SO_2$ is experimentally examined. Field strength is varied from -10 kV to 10 kV and configurations of conduction charging and induction charging are utilized. Consequently, the electrostatic removal efficiency of 501 increases about 30% with the applied voltage of ${\pm}10kV$ but is independent of polarity of the applied voltage. It Is also found that the conduction charging configuration results in higher efficiency of $SO_2$ removal that the induction charging configuration. Finally, the effect of slurry temperature on $SO_2$ removal is studied. The temperature influences on the electrostatic removal efficiency of $SO_2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.41.1-41.1
• /
• 2010

전기수력학적 분무를 이용한 액적 미립화 기술은 나노사이즈의 액적 형성, 쿨롱 반발력에 의한 균일한 액적 형성, 그리고 향상된 액적 타겟팅을 가능하게 한다. 따라서 이를 이용하여 매우 균일한 박막 코팅이 가능하다. 이러한 점에 힘입어 현재 진공 공정으로 제작되고 있는 CIGS태양전지의 광흡수층을 비진공 공정중 하나인 전기수력학적 미립화를 이용하여 실험하였다. Ethanol-based 의 CIGS나노 입자를 포함하는 콜로이드 상태의 전구체를 이용하여 적절히 가열된 몰리브덴 배면 전극위에 적용하였다. 미립화한 액적은 접지된 몰리브덴 층에 부착되는 즉시 증발하여 CIGS입자를 남긴다. 여기서 가장 중요하게 다루어야 할 조건은 기판의 온도, 인가 전압, 전구체의 유량이다. 분사 모드는 Cone-jet을 적용하였으며 5~15kV의 인가 전압에서 1ml/hr내외의 유량을 공급하여 3분 이내에 적절한 광흡수층 두께인 1마이크론 내외에 도달할 수 있다. 이와같은 조건으로 형성된 박막층에 관한 SEM image를 통해 다른 비진공 코팅 방식과 비교하였다.

• Journal of ILASS-Korea
• /
• v.5 no.3
• /
• pp.45-54
• /
• 2000

A novel electrostatic splaying method for solidifying a galvanized coating layer was studied. Our experimental results and computer simulations showed that electric field could assist the fine droplets to attach on the steel surface and change the sprayed droplets trajectory especially in the space near the steel surface. It was necessary to apply the electric voltage higher than - 20 kV to obtain the enough electrostatic attraction force between droplets and the steel sheet.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1068-1076
• /
• 1997

Emission control of acid exhaust gases from coal-fired power plants and waste incinerators has become an increasing concern of both industries and regulators. Among those gaseous emissions, SO$_{2}$ has been eliminated by a Spray Drying Absorber (SDA) system, where the exhaust gas is mixed with atomized limestone-water slurry droplets and then the chemical reaction of SO$_{2}$ with alkaline components of the liquid feed forms sulfates. Liquid atomization is necessary because it maximizes the reaction efficiency by increasing the total surface area of the alkaline components. An experimental study was performed with a laboratory scale SDA to investigate whether the scrubbing efficiency for SO$_{2}$ reduction increased or not with the application of a DC electric field to the limestone-water slurry. For a selected experimental condition SO$_{2}$ concentrations exited from the reactor were measured with various applied voltages and liquid flow rates. The applied voltage varied from -10 to 10 kV by 1 kV, and the volume flow rate of slurry was set to 15, 25, 35 ml/min which were within the range of emission mode. Consequently, the SO$_{2}$ scrubbing efficiency increased with increasing the applied voltage but was independent of the polarity of the applied voltage. For the electrical and flow conditions considered a theoretical study of estimating average size and charge of the atomized droplets was carried out based on the measured current-voltage characteristics. The droplet charge to mass ratio increased and the droplet diameter decreased as the strength of the applied voltage increased.