• Computational Structural Engineering
• /
• v.10 no.3
• /
• pp.145-155
• /
• 1997

In this study, static and dynamic transient analysis of tracked vehicle structure with recoil impact load is performed for transient impact and traveling load using ANSYS and ABAQUS FEM codes. When transient impact loads are applied at tracked vehicle, the maximum dynamic Von Mises stress occurs between beam stiffener of upper plate and race ring and stress level is about 390-450 MPa. The results of transient analysis shows similar level and tendency with static stress with dynamic force effect of 1.6. The excessive stresses occur around the race ring for the both cases. When the traveling loads are applied on the tracked vehicle, the maximum Tresca stress occurs around suspension #1 and is about 450 MPa and results of static and nonlinear transient analysis are quite similar.

• Journal of the Korean Society for Railway
• /
• v.14 no.1
• /
• pp.49-56
• /
• 2011

In this paper, it was compared the characteristics of the stress and settlement that occur from a track on the ground using a model test and has quantitatively analyzed the difference based on stress path and effect of the rotation of principal stress. Under identical roadbed conditions, the settlement generated by moving wheel loads were found to be 6 times and 3 times larger than that from static loads and cyclic loads, respectively. The deviator stress affecting shear deformation and the length of stress path generated by moving loads were twofold or greater increase than those by static loads. Furthermore, the stress path generated by moving loads was approached more closely to Mohr-Coulomb failure criteria compared to that by static loads. Also, it was found that ballasted track was occurred about 60% of maximum stress at $40^{\circ}$ of the rotation angle of principal stress and was affected with rotation of principal stress with moving wheel loading condition.

• Journal of Satellite, Information and Communications
• /
• v.5 no.1
• /
• pp.80-84
• /
• 2010

Satellite structure should be designed to accommodate and support safely the payload and equipments necessary for its own missions and to secure satellite and payloads from severe laucnch enviroments. The lauch environments imposed on satellites are quasi-static accelerations, aerodynamic loads, acoustic loads and shock loads. To qualify the structure design against low-frequency dyanmic enviromnent, sine vibration test should be performed. During sine vibration test, the notchings are implemented in order to keep the payloads and equipments from excessive loading at their own main modes. This paper deals with sine test prediction, sine vibration test results, comparison of predicted values and tested values, and verification of Finite Element Model.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.1
• /
• pp.33-40
• /
• 2014

Reliability analysis of jacket type offshore wind turbine (OWT) support structure under extreme ocean environmental loads was performed. Limit state function (LSF) of OWF support structure is defined by using structural dynamic response at mud-line. Then, the dynamic response is expressed as the static response multiplied by dynamic response factor (DRF). Probabilistic distribution of DRF is found from response time history under design significant wave load. Band limited beta distribution is used for internal friction angle of ground soil. Wind load is obtained in the form of thrust force from commercial code called GH_Bladed and then, applied to tower hub as random load. In a numerical example, the response surface method (RSM) is used to express LSF of jacket type support structure for 5MW OWF. Reliability index is found using first order reliability method (FORM).

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.433-439
• /
• 2007

The main objective of the paper is to investigate the static behavior of a prestressed concrete (PSC) girder that has been spliced with precast box segments. A 20 m long full-scale spliced PSC girder is fabricated and tested to compare its static performance against a monolithic girder. The monolithic girder has the same geometric and material properties with respect to the spliced girder. This includes infernal strain, deflections, neutral axis position, and crack patterns for both girders. The test also consists of monitoring relative displacements occurring across the joints. Both the horizontal displacement (gap) and vertical displacement (sliding) are measured throughout the loading procedure. All results have been compared to those obtained from the monolithic girder. It has been demonstrated that the spliced girder offers close behavior with respect to the monolithic girder up to the crack load. Both girders exhibits ductile flexural failure rather than abrupt shear failure at joints.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.657-665
• /
• 2011

LB-DECK, a precast concrete panel type, is a permanent concrete deck form used as a formwork for cast-in-place concrete pouring at bridge construction site. LB-DECK consists of 60 mm thick concrete slab and 125 mm height Lattice-girders partly embedded in the concrete slab. These decks have been applied to the bridges, which girder spacings are short enough to resist longitudinal cracking caused by construction loads. This paper presents experimental research work conducted to evaluate the cracking load of LB-DECKs designed for long span bridge decks. Twenty four non-composite beams and four composite beams are fabricated considering three design variables of thickness of concrete slab, height of lattice-girder, and diameter of top-bar. Static loads controlled by displacements are applied to test beams to obtain cracking and ultimate loads. Vertical displacements at the center of beams, strains of top-bar, crack propagation in concrete slab, and final failure modes are carefully monitored. The obtained cracking loads are compared to the analytical results obtained by elastic analyses. Long-term analyses using age-adjusted effective modulus method (AEMM) are also conducted to investigate the effects of concrete shrinkage on the cracking loads. Based on the test results, the tensile strength and the design details of LB-DECKs are discussed to prevent longitudinal cracking of long span bridge decks.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.1-201.1
• /
• 2016

전주된 Invar (Fe-35%Ni) 박판 위에 증착된 Cu 박막은 스퍼터 전력량이 증가할수록 증착속도가 증가하였다. Cu/Invar 박판이 Invar 박판보다 면저항 값이 34%로 작았다. Invar 박판 위에 Cu가 증착되면 최대자화와 투자율은 각각 40.3, 65.0 [%] 감소하였다. Cu 박막의 탄성하강강성도, 마찰계수, 피로한계는 각각 45, 0.130, 0.093 이었다. 동적 나노 압침법으로 얻은 Invaar/Cu 박막의 하중-시간-변위 곡선의 가장 큰 차이는 탄성하강강성도(elastic stiffness) 이었다. 미세경도와 나노경도의 실험적 관계식은 $Y[GPa]=9.18{\times}10^{-3}X[Hv]$ 이었다. 나노압침선단의 하중분포를 이차원 선형 및 비선형 유한요소해석을 통하여 1.0 [mN] 의 정적하중을 가한 Cu 박막은 486 [mN] 으로 예측되었다. 이는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.2
• /
• pp.23-29
• /
• 1989

The strain rate-sensitive constitutive models of steel and concrete were incorporated into a refined analytical procedure for loading rate-dependent axial/flexural analysis of reinforced concrete beam-columns. The predictions of the analytical technique compared well with both quasi-static and dynamic test results on reinforced concrete elements.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.44-57
• /
• 1992

본 보에서는 용접 구조물의 파괴 방지를 위한 제반 용접 구조 설계에 대하여 전반적으로 기술 하였다. 현대 용접 구조물의 각 선급이나 spec.에서 규정한 식들에 의해 산정된 정적하중으로 구조 설계되는 종래의 방법과는 달리, 유한 요소 구조 해석에 의한 강도 평가, 외부하중의 직접 계산에 의한 보다 정확한 설계 하중의 설정 및 통계적 처리를 통한 합리적인 구조해석(피로강도 포함)등으로 설계되고 있다. 더우기 구조설계시 구조물의 취성파괴를 고려한 파괴강도 및 인성 개념을 도입하였을 뿐 아니라 균열의 존재와 성장을 파괴 역학적으로 해석하여 구조물의 조업 중에서의 파괴관리 및 제어도 실시할 수 있는 총합적인 설계에 의하여 용접 구조물은 제작되고 있다. 비록 구조물의 총합적인 구조 설계로 제작되었을지라도, 구조물의 사용 성능은 용접부의 특성에 의하여 크게 변하게 되므로 용접 설계의 역할을 매우 중요하다. 용접 설계란 용접시공법, 구조부재 및 용접재료의 선정, 용접 이음부의 구조적 형상과 세부 형상 및 그외 용접에 관련된 제 인자들을 상호 유기적으로 조합함으로써 보다 경제적이고 신뢰성 있는 용접부를 얻고자 함에 그 목적이 있다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.124-124
• /
• 2017

Fe-Ni-Co 합금 박막(<$100{\mu}m$)을 황화물계 용액에서 전주공정으로 제조하였다. XRF로 측정한 박판의 평균 조성은 Fe-34 wt.% Ni-3 wt.% Co 이다. AFM으로 측정한 표면 조도는 35.2 nm 이다. 표면의 나노 경도는 평균 5.4 GPa 이었다. Oliver 모델을 적용한 구리 박막의 탄성하강강성도는 약 75 이었다. Alekhin 모델을 적용한 구리 박막의 마찰계수, 피로한계는 각각 0.134, 0.027 이었다. 유한요소법으로 평가한 Berkovich 형 나노압침선단의 하중분포를 이차원 선형 및 비선형 해석하면 1 [mN]의 정적하중을 가한 Fe-Ni-Co 박막은 약 576 [mN]로 예측되었다. 압침선단의 하중집중정도는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.